ASTM D7082-2004 Standard Specification for Polyethylene Stay In Place Form System for End Walls for Drainage Pipe《排水管端壁的聚乙烯固定型系统标准规范》.pdf

1、Designation: D 7082 04Standard Specification forPolyethylene Stay In Place Form System for End Walls forDrainage Pipe1This standard is issued under the fixed designation D 7082; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the y

2、ear of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification addresses the requirements for poly-ethylene stay in place forms for end walls or head wall

3、s for usewith standard storm drainage systems.1.2 The wall form system consists of a base wall form, acap, an optional riser to adjust the height of the wall above thepipe, and an optional adaptor to adjust the pipe opening toaccommodate smaller pipe sizes.1.3 The form system is manufactured using t

4、he rotationalmolding process and is available in different colors.1.4 The values stated in SI units are to be regarded as thestandard, the inch-pounds in brackets are given for informationonly.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. I

5、t is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory requirements prior to use.NOTE 1There is no similar or equivalent ISO standard.2. Referenced Documents2.1 ASTM Standards:2D 638 Test Method for Ten

6、sile Properties of PlasticsD 648 Test Method for Deflection Temperature of PlasticsUnder Flexural Load in the Edgewise PositionD 790 Test Methods for Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating MaterialsD 883 Terminology Relating to PlasticsD 1238 Test Method

7、 for Melt Flow Rates of Thermoplasticsby Extrusion PlastometerD 1505 Test Method for Density of Plastics by the Density-Gradient TechniqueD 1600 Terminology for Abbreviated Terms Relating toPlasticsD 1693 Test Method for Environmental Stress-Cracking ofEthylene PlasticsD 4883 Test Method for Density

8、 of Polyethylene by theUltrasound TechniqueD 5033 Guide for Development of ASTM Standards Relat-ing to Recycling and Use of Recycled Plastics3. Terminology3.1 DefinitionsDefinitions used in this specification are inaccordance with definitions in Terminology D 883and abbre-viations in accordance with

9、 Terminology D 1600 unless other-wise indicated.3.1.1 end walla wall installed at the outlet of a stormdrainage pipe.3.1.2 head walla wall installed at the inlet of a stormdrainage pipe.4. Ordering Information4.1 Number and color of base wall forms,4.2 Number and color of riser forms,4.3 Number and

10、color of caps, and4.4 Number, color and size of adaptors.5. Materials and Manufacture5.1 The material used shall be a polyethylene meeting thecriteria in Table 1.5.2 Only virgin materials (Guide D 5033) shall be used.5.3 This product shall be manufactured using a rotationalmolding process.6. Require

11、ments6.1 Wall System Description:6.1.1 Base wall form is hollow with opening at the top toaccept fill material and designed to accept either cap or risersection. Base wall has opening in the center for pipe andadaptors as needed. Pipe is secured to base wall form withgalvanized screws. (See Fig. 1.)

12、6.1.2 Riser form is hollow with opening at top to accept fillmaterial and cap section. Multiple risers can be installed onbase wall. (See Fig. 2.)6.1.3 Cap fits on top of base wall or riser and is secured withgalvanized screws. (See Fig. 1.)1This specification is under the jurisdiction of ASTM Commi

13、ttee D20 onPlastics and is the direct responsibility of Subcommittee D20.20 on Plastic Products.Current edition approved November 1, 2004. Published November 2004.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book

14、 of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6.1.4 Adaptor section is used to adjust the size of the pipeopening as needed. Adap

15、tor is secured to base wall form withgalvanized screws and pipe is secured to adaptor with galva-nized screws. (See Fig. 2.)6.2 Workmanship, Finish, and Appearance:6.2.1 Workmanship of the form system components shall besuch that the quality is agreeable between the producer and theend user.6.2.2 Th

16、e surface of the form system components shall befinished to mimic a split stone face, with the appearance ofmortar joints and with the vertical joints offset on alternatingcourses.6.2.3 Physical properties of finished form system compo-nents.6.2.3.1 DimensionsSee Figs. 1 and 2.7. Test Methods7.1 Phy

17、sical Properties:7.1.1 Dimensions shall be measured to the nearest 2 mmwith the exception of the material thickness, which is measuredas noted on Fig. 2, Note E.TABLE 1 Material SpecificationsResin Properties ASTM Method Value UnitsDensity (Range) D 1505 / D 4883 0.9335 0.9395 g/ccMelt Index (Range)

18、 D 1238 Cond. 190C, 2.16 kg 3.5 7.5 g/10 minEnvironmental Stress Crack Resistance (ESCR), F50D 1693, Cond. A100 % lgepal10 % lgepal27555HrHrFlexural Modulus (Minimum) D 790 at 1 % secant Procedure B 600 87 Mpa kpsiTensile Strength at Yield (Minimum) D 638, Type IV specimen 17.2 2500 Mpa psiTensile B

19、reak Elongation (Minimum) 50.8 mm/min 3.12 mm thick2 in./min 18 in. thick420 %Deflection Temperature (Minimum) D 648 0.455 MPa 66 psi 1.82 MPa 264 psi5035CCFIG. 1 Base Wall and LidD70820428. Sampling, Inspection, and Retest8.1 SamplingThe selection of samples shall be as agreedupon by the purchaser

20、and the seller. Unless otherwise speci-fied, a minimum of five randomly selected samples shall betested.8.2 Inspection:8.2.1 Inspection and TestingInspection and testing shallbe made as agreed upon between the purchaser and themanufacturer as part of the purchase contract.8.3 Retest and RejectionIf

21、the results of any test(s) do notmeet the requirements of this specification, the test(s) shall beconducted again only if agreed to by the purchaser and theseller.9. Certification9.1 When specified in the purchase order or contract, amanufacturers certification that the material was designed,manufac

22、tured, sampled, tested, and inspected in accordancewith this specification, and has been found to meet therequirements shall be furnished to the purchaser. When speci-fied in the purchase order or contract, a report of the test resultsshall be furnished. Each certification so furnished shall besigne

23、d by an authorized agent of the manufacturer.10. Product Marking10.1 Marking on the product shall include the following:10.1.1 The letters “ASTM” followed by the designationnumber of this specification,10.1.2 The letters “PE,”10.1.3 The product name, and10.1.4 The name or trademark of the manufactur

24、er.11. Packaging and Package Marking11.1 Unless otherwise specified in the contract, materialsshall be packaged in accordance with the suppliers standardpractice.12. Quality Assurance12.1 When the product is marked with this designation,D 7082, the manufacturer affirms that the product was manu-fact

25、ured, inspected, sampled, and tested in accordance with thisspecification and has been found to meet the requirements ofthis specification.13. Keywords13.1 drainage; endwall; headwall; stay in place formFIG. 2 Optional Riser Section and AdaptorD7082043ASTM International takes no position respecting

26、the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard

27、 is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International

28、Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This

29、 standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D7082044