ASTM D7106-2005 Standard Guide for Selection of Test Methods for Ethylene Propylene Diene Terpolymer (EPDM) Geomembranes《乙烯-丙烯-二烯三元共聚物土工薄膜的试验方法选择的标准指南》.pdf

1、Designation: D 7106 05Standard Guide forSelection of Test Methods for Ethylene Propylene DieneTerpolymer (EPDM) Geomembranes1This standard is issued under the fixed designation D 7106; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision

2、, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This standard guide provides recommendations for theselection of appropriate test methods for Ethylene

3、PropyleneDiene Terpolymer (EPDM) geomembranes used in geotechni-cal and geoenvironmental applications.1.2 This guide includes test methods for three differenttypes of EPDM geomembranes including; scrim-reinforcedmembranes, composite membranes and smooth, non-reinforced membranes.1.3 The test methods

4、 are divided into three categoriesincluding manufacturing quality control, optional performancetests and seam testing.1.4 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are provided forinformation purposes only.1.5 This standard does not purport to a

5、ddress all of thesafety problems, if any associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 297 Test M

6、ethod for Rubber Products-Chemical AnalysisD 413 Test Method for Rubber Property-Adhesion to Flex-ible SubstrateD 471 Test Method for Rubber Property- Effect of LiquidsD 618 Practice for Conditioning Plastics and ElectricalInsulating Materials for TestingD 882 Test Method for Tensile Properties of T

7、hin PlasticSheetingD 1004 Test Method for Initial Tear Resistance of PlasticFilm and SheetingD 1149 Test Method for Rubber Deterioration-SurfaceOzone Cracking in a ChamberD 1204 Test Method for Linear Dimension Changes ofNonrigid Thermoplastic Sheeting or Film at ElevatedTemperatureD 1418 Practice f

8、or Rubber and Rubber Latices - Nomen-clatureD 1434 Test Method for Determining Gas PermeabilityCharacteristics of Plastic Film and SheetingD 2137 Test Method for Rubber Property BrittlenessPoint of Flexible Polymers and Coated FabricsD 2240 Test Method for Rubber Property by DurometerHardnessD 4355

9、Test Method for Deterioration of Geotextiles byExposure to Light, Moisture and Heat in a XenonArc TypeApparatusD 4437 Practice for Determining the Integrity of FieldSeams Used in Joining Flexible Polymeric SheetGeomembranesD 4439 Terminology for GeosyntheticsD 4637 Specification for EPDM Sheet Used

10、in Single-PlyRoof MembraneD 4833 Test Method for Index Puncture Resistance ofGeotextiles, Geomembranes, and Related ProductsD 5199 Test Method for Measuring Norminal Thickness ofGeotextiles and GeomembranesD 5321 Standard Test Method for Determining the Coeffi-cient of Soil and Geosysthethics or Geo

11、synthetic Frictionby the Direct Shear MethodD 5514 Test Method for Large Scale Hydrostatic PunctureTesting of GeosynthethicsD 5617 Test Method for Multi-Axial Tension Test for Geo-systheticsD 5721 Standard Practice for Air-Oven Aging of PolyolefinGeomembranesD 5884 Test Method for Determining Tearin

12、g Strength ofInternally Reinforced GeomembranesD 7004 Test Method for Grab Tensile Properties of Rein-forced GeomembranesE96 Test Method for Water Vapor Transmission of Mate-rials1This guide is under the jurisdiction ofASTM Committee D35 on Geosyntheticsand is the direct responsibility of Subcommitt

13、ee D35.10 on Geomembranes.Current edition approved June 1, 2005. Published July 2005.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary

14、page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3. Terminology3.1 Definitions:3.1.1 EPDM,n-terpolymer of ethylene, propylene, and dienewith the residual unsaturated portion of the diene in the sidechain. (ASTM

15、 D 1418)3.1.2 For definitions of other geosynthetic terms used in thisguide, refer to ASTM D 4439 Standard Terminology forGeosynthetics.3.1.3 Composite membrane, nfactory laminated non-woven geotextile and EPDM4. Significance and Use4.1 This standard provides guidance to obtain data that isthe most

16、representative of the materials characteristics andperformance. To properly evaluate EPDM, tests should beperformed in accordance with specific test methods and pro-cedures.5. Test Methods5.1 The recommended test methods for EPDM sheet arelisted in tables under the following categories:Table 1: Test

17、 Methods for Manufacturing Quality Control ofEPDM SheetTable 2: Performance Test Methods for EPDM SheetTable 3: Test Methods for Seams of EPDM Sheet6. Keywords6.1 geomembrane; EPDM; sheetTABLE 1 Test Methods for Manufacturing Quality Control of EPDM SheetTestTitleSheet TypeConditions:Reinforced Comp

18、osite SmoothNon-reinforcedGeneral:Terminology D 4439 D 4439 D 4439Conditioning D 618 D 618 D 618Physical Properties:Thickness D 5199 D 5199 D 5199Thickness of Coatingover ScrimD 4637 D 4637 Optical Method, AnnexA1Density D 297 D 297 D 297DurometerHardnessD 2240AD 2240AD 2240 Shore AMechanical Proper

19、ties:Ultimate TensileStrength andElongationD 882 Strip width =25mm(1.0in); Strainrate500mm(20in)/minBreaking Strength D 7004 D 7004 Grab Test MethodTear Resistance D 1004Tear Strength D 5884 D 5884Puncture Strength D 4833 D 4833 D 4833Ply Adhesion D 413Fabric Adhesion D 413ATest specimens should be

20、prepared from the coating compound, vulcanized in a similar manner to the scrim-reinforced and composite productsD7106052ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expres

21、sly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised,

22、 either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may at

23、tend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States.

24、 Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 2 Performance Test Methods for EPDM SheetTestTitleShee

25、t Type Test ParametersReinforced Composite SmoothNonreinforcedPhysical Properties:Water VaporTransmissionE96AE96AE96 23C (73F) / 50 %RHGasTransmissionD 1434AD 1434AD 1434 70C (158F) / 160 hWater Absorption D 471AD 471AD 471 70C (158F) / 160hMechanical Properties:HydrostaticResistanceD 5514 D 5514 D

26、5514Multi-Axial Tensile D 5617 D 5617 D 5617Direct Shear D 5321 D 5321 D 5321Thermal Properties:DimensionalStabilityD 1204 D 1204 D 1204 115C (239F) / 670hBrittleness Point D 2137 D 2137 D 2137Endurance Properties:Resistance toArtificial WeatheringD 4355 D 4355 D 4355 As per this test StandardOzone

27、Resistance D 1149 D 1149 D 1149Oven Aging D 5721 D 5721 D 5721 115C (239F) / 670hChemical Resistance D 5747 D 5747 D 5747 As agreed to bymanufacturer and end userATest specimens should be prepared from the coating compound, vulcanized in a similar manner to the scrim-reinforced and composite product

28、s.TABLE 3 Test Methods for Seam Testing of EPDM SheetSeam Properties: Test Method: Comments:Peel Adhesion Seam Testing D 4437 Strip width: 25mm (1.0in)Grip Separation: 50mm (2.0in) + Seam WidthStrain rate =500mm(20in)/min Maximum teststrain: 200 %Shear Strength Seam Testing D 4437 Strip width: 25mm (1.0in)Grip Separation: 50mm (2.0in) + Seam WidthStrain rate =500mm(20in)/min Maximum teststrain: 200 %Non-destructive Test of Seam Testing using Air Lance D 4437D7106053