ImageVerifierCode 换一换
格式:PDF , 页数:6 ,大小:193.23KB ,
资源ID:524512      下载积分:5000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-524512.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM D7107-2004 Standard Test Method for Creep Measurement of Self-Lubricating Bushings《自润滑套管的蠕变测量的标准试验方法》.pdf)为本站会员(outsidejudge265)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ASTM D7107-2004 Standard Test Method for Creep Measurement of Self-Lubricating Bushings《自润滑套管的蠕变测量的标准试验方法》.pdf

1、Designation: D 7107 04Standard Test Method forCreep Measurement of Self-Lubricating Bushings1This standard is issued under the fixed designation D 7107; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A n

2、umber in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method determines the amount of creep exhib-ited by self-lubricating bushings exposed to a high load for anextended period of

3、 time.1.2 This test method is designed to reproduce conditionstypical of those encountered by trunnion bushings in hydro-power applications and any other bushings subjected to highcontinuous loading and low-speed oscillating applications.1.3 This test method is conducted on cut segments of thebushin

4、gs.1.4 The values given in SI units are to be regarded as thestandard in all property and dimensional tables.NOTE 1There is no equivalent ISO standard.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this

5、 standard to establish appro-priate safety and health practices and to determine theapplicability of regulatory limitations prior to use.2. Terminology2.1 Definitions:2.1.1 creep strain, ntotal strain, at any given time, pro-duced by the applied stress during a creep test.3. Summary of Test Method3.

6、1 Segments of the bushing are mounted in-line on the testapparatus such that when load is applied at one end of theapparatus, by means of a hydraulic cylinder, all specimens aresimultaneously loaded exactly the same.3.2 Bearing test pressure is maintained at 55 160 kPa 8000psi on the projected area

7、of the bushing specimen.3.3 Pressure is held constant by means of an automaticpumping system and an accumulator.3.4 The actual amount of creep is measured over an ex-tended period of time.4. Significance and Use4.1 Self-lubricating bushings with low creep rates are usedin hydropower turbines and oth

8、er applications in which bush-ing distortion could cause misalignment of shafts and linkages.4.2 An assumption is made that if the creep is satisfactory at55 160 kPa 8000 psi, it will also be satisfactory at lowerpressures.5. Apparatus5.1 The loading frame shall be capable of applying andmaintaining

9、 the required load on the specimens, despite anychange in the dimensions of the specimens.5.2 Bushing specimens are mounted in-line on the testapparatus such that when load is applied at one end of theapparatus (by means of a hydraulic cylinder) all specimensreceive the same load.5.3 Bearing test pr

10、essure is maintained at 55 160 kPa 8000psi on the projected area of the bushing specimen.5.4 Pressure is held (nearly) constant by means of anautomatic pumping system and an accumulator.5.5 A suitable test frame configuration is shown in AnnexA1.5.6 The creep-measuring device consists of an eddy-cur

11、rentsensor anchored to one end of a specimen group (four testsamples) directed at a target attached to the other end of thegroup.5.7 The overall change in lengths of the four specimens ismonitored to an accuracy of 2.54 m 0.0001 in.6. Test Specimens and Test Units6.1 Paragraph 6.2 and Fig. 1 define

12、the test sample configu-ration. The samples are clamped into sample supports asdescribed in Section 7.6.2 Each test shall use four identical bushing materialspecimens meeting the following requirements (reference Fig.1):6.2.1 Inside Radius of Tubular Form6.350 6 0.013 cm2.500 6 0.005 in.,6.2.2 Thick

13、ness0.952 6 0.005 cm 0.375 6 0.002 in.,6.2.3 Length6.98 + 0.000/-0.013 cm 2.75 + 0.000/-0.005in.,6.2.4 Angle of Arc (Each Finished Specimen)120 6 1.0,and6.2.5 Surface FinishRa3.2 m 125 in. minimum.7. Preparation of Apparatus7.1 Sample Spacer:7.1.1 Material and TemperAL 6061 T6 or T6511,7.1.2 Diamete

14、r2.700 6 0.005 cm 5.000 6 0.002 in.,1This test method is under the jurisdiction of ASTM Committee D20 on Plasticsand is the direct responsibility of Subcommittee D20.20 on Plastic Products.Current edition approved December 1, 2004. Published December 2004.1Copyright ASTM International, 100 Barr Harb

15、or Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.7.1.3 Length6.985 + 0.000/-0.025 cm 2.75 + 0.000/-0.010 in.,7.1.4 PerpendicularityEnds perpendicular with cylinderaxis within 50 m 0.002 in., and7.1.5 Surface FinishRa0.4 m 16 in. minimum.7.2 Sample Supports:7.2.1 Material and Te

16、mperAL 6061 T6 or T6511,7.2.2 Radii7.302 6 0.025 cm 2.875 6 0.010 in.,7.2.3 Length6.985 + 0.000/-0.025 cm 2.75 + 0.000/-0.010 in., and7.2.4 Radii Surface FinishesRa0.8 m 32 in. mini-mum.7.3 Other Machined Parts and Sample Clamps:7.3.1 Material and TemperAL 6061 T6 or T6511 and7.3.2 FinishRa3.2 m 125

17、 in.7.4 AssemblyFIG. 1 Test Sample ConfigurationD71070427.4.1 The test specimens and the inside surface of thespecimen supports shall be cleaned with dishwashing detergentand water followed by a thorough rinse with water and dried.(Air dry thoroughly before assembly.)7.4.2 The specimen shall be plac

18、ed in the supports andclamped in place.7.4.3 The complete frame shall be assembled with speci-mens, spacers, and instrumentation.8. Calibration and Standardization8.1 Eddy-current probes are calibrated in accordance withmanufacturers recommendations.8.2 Thermocouples are calibrated in accorrdance wi

19、thmanufacturers recommendations.9. Conditioning9.1 All storage and testing of specimens shall be conductedat room temperature (18 to 25C).10. Procedure10.1 The test frames shall be set up in an area in whichtemperature changes are limited to 20 6 1C 68 6 2F.10.2 Each specimen shall be premounted in

20、the test blockand clamped in place.10.3 The four specimens for each material shall be preas-sembled as a group.10.4 Two groups of specimens shall be placed in the framebetween the tension rods.10.5 The hydraulic ram and loading block shall also be laidin the frame in alignment with the specimens.10.

21、6 The frame shall be inserted into a tank sufficiently largeto contain the entire frame.10.7 The tank shall be filled with distilled water completelycovering the test specimens.10.8 The eddy-current displacement probes shall bemounted on each group of specimens.10.9 A load of 4082 6 90 kg 9000 6 200

22、 lb is applied for24 h.NOTE 2This load is sufficient to provide pressure of 5171 kPa 750psi on the projected area of the bearing specimen.10.10 Start the recording device to log temperature anddisplacement once an hour every hour for 24 h.10.11 Apply a load of 43 200 6 227 kg 95 250 6 500 lb(that is

23、, 60.5 %) and maintain the load for 360 days.NOTE 3This load is sufficient to provide pressure of 55 160 kPa 8000psi on the projected area of the bearing specimen.10.12 Continue recording once every 4 h after the first 24h. After one month, record once a day.10.13 Monitor pressure on a weekly basis

24、and increase ifand when necessary.11. Calculation11.1 Plot displacement data (creep strain) versus elapsedtime.11.2 Determine elapsed time at which creep strain ceases.11.3 Calculate amount of creep per unit thickness of theproduct.12. Report12.1 Name of the product tested and the name and addressof

25、 the manufacturer.12.2 Displacement data (see 11.1).12.3 Observations made during test providing details of anyvariations of temperature, times when pressure (load) requiredadjustment, and details of unusual events that occurred.13. Precision and Bias13.1 Insufficient data are available at the prese

26、nt time todevelop repeatability data. The test is expensive and time-consuming (360 days). Data will be developed and addedwithin the earliest convenient timeframe.14. Keywords14.1 bushings; material creepD7107043ANNEX(Mandatory Information)A1. COMPRESSION FRAMEA1.1 The general configuration of a te

27、st frame capable ofholding two groups of four specimens is shown in Figs.A1.1-A1.3FIG. A1.1 Overview of Creep Test ApparatusD7107044FIG. A1.2 Parts Description of Creep ApparatusD7107045ASTM International takes no position respecting the validity of any patent rights asserted in connection with any

28、item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical c

29、ommittee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at

30、a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Dr

31、ive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).FIG. A1.3 Exploded View of Creep ApparatusD7107046

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1