ASTM D7223-2011 4375 Standard Specification for Aviation Certification Turbine Fuel《航空认证涡轮机燃料的标准规范》.pdf

1、Designation: D7223 11An American National StandardStandard Specification forAviation Certification Turbine Fuel1This standard is issued under the fixed designation D7223; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of

2、last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers the use of purchasing agenciesin formulating specifications for purchases of aviation turbi

3、nefuel under contract.1.2 This specification defines one specific type of aviationturbine fuel for civil use in the certification of aircraft. Thespecification can be used as a standard in describing the qualityof this aviation fuel from the refinery to the aircraft.1.3 This specification does not i

4、nclude the fuels that arecommonly used in aviation turbine engines. Those are listed inSpecification D1655.1.4 The aviation turbine fuel defined by this specificationmay be used in other than turbine engines that are specificallydesigned and certified for this fuel.1.5 The values stated in SI units

5、are to be regarded asstandard. No other units of measurement are included in thisstandard.2. Referenced Documents2.1 ASTM Standards:2D56 Test Method for Flash Point by Tag Closed Cup TesterD86 Test Method for Distillation of Petroleum Products atAtmospheric PressureD130 Test Method for Corrosiveness

6、 to Copper from Pe-troleum Products by Copper Strip TestD381 Test Method for Gum Content in Fuels by Jet Evapo-rationD445 Test Method for Kinematic Viscosity of Transparentand Opaque Liquids (and Calculation of Dynamic Viscos-ity)D1266 Test Method for Sulfur in Petroleum Products(Lamp Method)D1298 T

7、est Method for Density, Relative Density (SpecificGravity), or API Gravity of Crude Petroleum and LiquidPetroleum Products by Hydrometer MethodD1319 Test Method for Hydrocarbon Types in LiquidPetroleum Products by Fluorescent Indicator AdsorptionD1322 Test Method for Smoke Point of Kerosine andAviat

8、ion Turbine FuelD1655 Specification for Aviation Turbine FuelsD1840 Test Method for Naphthalene Hydrocarbons inAvia-tion Turbine Fuels by Ultraviolet SpectrophotometryD2386 Test Method for Freezing Point of Aviation FuelsD2622 Test Method for Sulfur in Petroleum Products byWavelength Dispersive X-ra

9、y Fluorescence SpectrometryD2624 Test Methods for Electrical Conductivity ofAviationand Distillate FuelsD2887 Test Method for Boiling Range Distribution ofPetroleum Fractions by Gas ChromatographyD3227 Test Method for (Thiol Mercaptan) Sulfur in Gaso-line, Kerosine, Aviation Turbine, and Distillate

10、Fuels(Potentiometric Method)D3241 Test Method for Thermal Oxidation Stability ofAviation Turbine FuelsD3242 Test Method for Acidity in Aviation Turbine FuelD3338 Test Method for Estimation of Net Heat of Combus-tion of Aviation FuelsD3828 Test Methods for Flash Point by Small Scale ClosedCup TesterD

11、3948 Test Method for Determining Water SeparationCharacteristics of Aviation Turbine Fuels by PortableSeparometerD4052 Test Method for Density, Relative Density, and APIGravity of Liquids by Digital Density MeterD4057 Practice for Manual Sampling of Petroleum andPetroleum ProductsD4171 Specification

12、 for Fuel System Icing InhibitorsD4294 Test Method for Sulfur in Petroleum and PetroleumProducts by Energy Dispersive X-ray Fluorescence Spec-trometryD4306 Practice for Aviation Fuel Sample Containers forTests Affected by Trace ContaminationD4529 Test Method for Estimation of Net Heat of Combus-tion

13、 of Aviation Fuels1This specification is under the jurisdiction of ASTM Committee D02 onPetroleum Products and Lubricants and is the direct responsibility of SubcommitteeD02.J0 on Aviation Fuels.Current edition approved July 15, 2011. Published August 2011. Originallyapproved in 2005. Last previous

14、edition approved in 2010 as D722310. DOI:10.1520/D7223-11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A

15、 Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.D4809 Test Method for Heat of Combustion of LiquidHydrocarbon Fuels by Bomb Calorimeter (PrecisionMethod)D4952 Test Method

16、 for Qualitative Analysis for ActiveSulfur Species in Fuels and Solvents (Doctor Test)D5001 Test Method for Measurement of Lubricity of Avia-tion Turbine Fuels by the Ball-on-Cylinder LubricityEvaluator (BOCLE)D5006 Test Method for Measurement of Fuel System IcingInhibitors (Ether Type) in Aviation

17、FuelsD5453 Test Method for Determination of Total Sulfur inLight Hydrocarbons, Spark Ignition Engine Fuel, DieselEngine Fuel, and Engine Oil by Ultraviolet FluorescenceD5972 Test Method for Freezing Point of Aviation Fuels(Automatic Phase Transition Method)D6378 Test Method for Determination of Vapo

18、r Pressure(VPX) of Petroleum Products, Hydrocarbons, andHydrocarbon-Oxygenate Mixtures (Triple ExpansionMethod)D6469 Guide for Microbial Contamination in Fuels andFuel SystemsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with Specifications3. General3.1 This specific

19、ation, unless otherwise provided, prescribesthe required properties of aviation certification turbine fuel atthe time and place of delivery.4. Classification4.1 One type of aviation turbine fuel is provided, as follows:4.1.1 Jet C-1A relatively wide boiling range volatiledistillate.5. Materials and

20、Manufacture5.1 Aviation turbine fuel, except as otherwise specified inthis specification, shall consist of blends of refined hydrocar-bons (see Note 1) derived from conventional sources includingcrude oil, natural gas liquid condensates, heavy oil, shale oil,and oil sands. The use of jet fuel blends

21、, containing compo-nents from other sources, is permitted only on a specific,individual basis (seeAnnexA1 on fuels from non-conventionalsources in Specification D1655).NOTE 1Conventionally refined jet fuel contains trace levels of mate-rials which are not hydrocarbons, including oxygenates, organosu

22、lfur, andnitrogeneous compounds.5.1.1 Fuels used in engines and aircraft are ultimatelyapproved by the certifying authority subsequent to formalsubmission of evidence to the authority as part of the typecertification program for that aircraft and engine model.Additives to be used as supplements to a

23、n approved fuel mustalso be similarly approved on an individual basis (see Speci-fication D1655).5.2 AdditivesMay be added to this aviation turbine fuel inthe amount and of the composition specified in the followinglist of approved material:35.2.1 AntioxidantsIn amounts not to exceed 24.0 mg/Lactive

24、 ingredients (not including weight of solvent):5.2.1.1 2,6-ditertiary-butyl phenol.5.2.1.2 2,6-ditertiary-butyl-4-methyl phenol.5.2.1.3 2,4-dimethyl-6-tertiary-butyl phenol.5.2.1.4 75 % minimum 2,6-ditertiary-butyl phenol, plus25 % maximum mixed tertiary and tritertiary-butyl phenols.5.2.1.5 55 % mi

25、nimum 2,4-dimethyl-6-tertiary-butyl phe-nol, plus 15 % minimum 2,6-ditertiary-butyl-4-methyl phenol,remainder as monomethyl and dimethyl tertiary-butyl phenols.5.2.1.6 72 % minimum 2,4-dimethyl-6-tertiary-butyl phe-nol, 28 % maximum monomethyl and dimethyl-tertiary-butylphenols.5.2.2 Metal Deactivat

26、or Additive (MDA), in amount not toexceed 2.0 mg/L (not including weight of solvent) on initialfuel manufacture at the refinery. Higher initial concentrationsare permitted in circumstances where copper contamination issuspected to occur during distribution. Cumulative concentra-tion of MDA when retr

27、eating the fuel shall not exceed5.7 mg/L:5.2.2.1 N,N-disalicylidene-1,2-propane diamine.5.2.3 Electrical Conductivity AdditiveStadis 4504not toexceed 3 mg/L.5.2.3.1 When loss of fuel conductivity necessitates retreat-ment with electrical conductivity additive, the following con-centration limits app

28、ly:At Manufacture:Stadis 450 3 mg/L, maxRetreatment:Stadis 450 cumulative total 5 mg/L, max5.2.4 Leak Detection AdditiveTracer A (LDTA-A)5maybe added to the fuel in amounts not to exceed 1 mg/kg.5.2.5 Other additives are permitted. These include fuelsystem icing inhibitor and special purpose additiv

29、es such asbiocides. The quantities and types must be declared by the fuelsupplier and agreed to by the purchaser. Only additivesapproved by the aircraft certifying authority are permitted inthe fuel on which an aircraft is operated.5.2.5.1 Biocidal additives are available for controlled usage.Where

30、such an additive is used in the fuel, the approval statusof the additive and associated conditions must be checked forthe specific aircraft and engines to be operated.5.2.5.2 Fuel System Icing Inhibitor:(1) Diethylene Glycol Monomethyl Ether (DIEGME), con-forming to the requirements of Specification

31、 D4171, Type III,may be used in concentrations of 0.10 to 0.15 volume %.(2) Test Method D5006 may be used to determine theconcentration of DIEGME in aviation fuels.3Supporting data (Guidelines for Approval or Disapproval of Additives) havebeen filed at ASTM International Headquarters and may be obta

32、ined by requestingResearch Report RR:D02-1125.4Stadis 450 is a registered trademark marketed by Innospec Inc., InnospecManufacturing Park, Oil Sites Road, Ellesmere Port, Cheshire, CH65 4EY, UK.5Tracer A (LDTA-A) is a registered trademark of Tracer Research Corp., 3755N. Business Center Dr., Tucson,

33、 AZ 85705.D7223 1125.3 Guidance material is presented in Appendix X3 ofSpecification D1655 concerning the need to control processingadditives in jet fuel production.6. Detailed Requirements6.1 The aviation turbine fuel shall conform to the require-ments prescribed in Table 1.6.2 Test results shall n

34、ot exceed the maximum or be lessthan the minimum values specified in Table 1. No allowanceshall be made for the precision of the test methods. Todetermine conformance to the specification requirement, a testresult may be rounded to the same number of significant figuresas in Table 1 using Practice E

35、29. Where multiple determina-tions are made, the average result, rounded according toPractice E29, shall be used.6.3 If any additives are used, the aviation turbine fuel shallconform to the Table 2 listed requirements.7. Workmanship, Finish and Appearance7.1 The aviation turbine fuel herein specifie

36、d shall bevisually free of undissolved water, sediment, and suspendedmatter. The odor of the fuel shall not be nauseating or irritating.TABLE 1 Detailed Requirements of Aviation Certification Turbine FuelAProperty Jet C-1 ASTM Test MethodBAcidity, total mg KOH/g max 0.10 D3242Aromatics, vol % min/ma

37、x 8 to 25 D1319Sulfur, mercaptanC, weight % max 0.003 D3227Sulfur, total weight % max 0.30 D1266, D2622, D4294 or D5453Distillation temperature, C (F):Initial boiling point, temperature min/max 70/100 (158/212) D2887, D86D5 % recovered, temperature min/max 80/110 (176/230) D2887, D86D10 % recovered,

38、 temperature min/max 90/120 (194/248) D2887, D86D20 % recovered, temperature min/max 105/140 (221/284) D2887, D86D50 % recovered, temperature min/max 150/195 (302/383) D2887, D86D90 % recovered, temperature min/max 215/255 (419/491) D2887, D86DFinal boiling point, temperature min/max 240/290 (464/55

39、4) D2887, D86DFlash Point, C (F) report D56, D3828Density at 15C, kg/m3750 to 840 D1298, D4052Vapor pressureEat 25C, kPa (psi) report 3.0 (0.44) to 5.5 (0.80) D6378Fat 38C, kPa (psi) report 5.6 (0.8) to 8.2 (1.2) D6378Fat 50C, kPa (psi) min/max 10.0 (1.45) to 12.5 (1.82) D6378Fat 100C, kPa (psi) rep

40、ort 56 (8.1) to 60 (8.7) D6378FFreezing point, C max -35 D2386, D5972GViscosity at -20C, mm2/sHmax 8.0 D445Net heat of combustion, MJ/kg min 42.8ID4529, D3338,orD4809One of the following requirements shall be met:(1) Smoke point, mm, or min 25 D1322(2) Smoke point, mm, and min 18 D1322Naphthalenes,

41、vol, % max 3.0 D1840Copper strip, 2 h at 100C max No. 1 D130Thermal stability:(2.5 h at control temperature of 260C min):Filter pressure drop, mm Hg max 25 D3241JTube deposit less than 3 D3241No Peacock or Abnormal Color DepositsExistent gum, mg/100 mL max 7 D381Microseparometer,KRating max 1b D3948

42、Without electrical conductivity additive min 85With electrical conductivity additive min 70LubricityL BOCLE WSD, mm max 0.85 D5001LAdditives: see 5.2Electrical conductivity, pS/m required 50 to 600 D2624Other optionalAFor compliance of test results against the requirements of Table 1, see 6.2.BThe t

43、est methods indicated in this table are referred to in Section 10.CThe mercaptan sulfur determination may be waived if the fuel is considered sweet by the doctor test described in Test Method D4952.DIf Test Method D2887 is used, use correlation procedure (Appendix X5) in Test Method D2887 to convert

44、 D2887 temperatures to D86 equivalent temperatures. Bothminimums and maximums shall be met.EAbsolute vapor pressure (VPx) is the primary property to be controlled; 2,2 dimethylbutane and toluene, as cited in Section 11 and Note 14 of Test Method D637808,shall be used as verification fluids. 1.0 kPa

45、= 0.145 psi.FLatest version. Record absolute vapor pressure (VPx).GTest Method D5972 may produce a higher (warmer) result than that from Test Method D2386. In case of dispute, Test Method D2386 shall be the referee method.H1mm2/s=1cSt.IUse either Eq 1 or Table 1 in Test Method D4529 or Eq 2 in Test

46、Method D3338. Test Method D4809 may be used as an alternative. In case of dispute, Test MethodD4809 shall be used.JTube deposits shall always be reported by the Visual Method.KAt point of manufacture.LLubricity test can be waved with purchasers agreement.D7223 113No substance of known dangerous toxi

47、city under usual condi-tions of handling and use shall be present, except as permittedin this specification.8. Sampling8.1 Because of the importance of proper sampling proce-dures in establishing fuel quality, use the appropriate proce-dures in Practice D4057 to obtain a representative sample fromth

48、e batch of fuel for specification compliance testing. Thisrequirement is met by producing fuel as a discrete batch thentesting it for specification compliance. This requirement is notsatisfied by averaging online analysis results.8.2 A number of jet fuel properties including thermalstability, water

49、separation, electrical conductivity, and othersare very sensitive to trace contamination that can originatefrom sample containers. For recommended sample containersrefer to Practice D4306.9. Report9.1 The type and number of reports to ensure conformancewith the requirements of this specification shall be mutuallyagreed upon by the seller and the purchaser of the aviationturbine fuel.9.2 A suggested form for reporting inspection data onaviation turbine fuel is given in Specification D1655.10. Test Methods10.1 Determine the requirements enumerated in this speci-