ASTM D7547-2017 red 7500 Standard Specification for Hydrocarbon Unleaded Aviation Gasoline《烃类无铅航空汽油的标准规格》.pdf

1、Designation: D7547 151D7547 17 An American National StandardStandard Specification forHydrocarbon Unleaded Aviation Gasoline1This standard is issued under the fixed designation D7547; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision,

2、 the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1 NOTETitle of Table 1 was corrected editorially in December 2016.1. Scope*1.1 This specification covers formulating

3、specifications for purchases of aviation gasoline under contract and is intendedprimarily for use by purchasing agencies.1.2 Unleaded aviation gasoline defined by this specification is for use in engines and associated aircraft that are specificallyapproved by the engine and aircraft manufacturers.

4、This fuel is not considered suitable for use in other engines and associatedaircraft that are certified to use only leaded aviation gasolines of the same octane grade.1.3 This specification, unless otherwise provided, prescribes the required properties of unleaded aviation gasoline at the timeand pl

5、ace of delivery.1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standar

6、d to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardizationestablished in the Decision on Principles for the Deve

7、lopment of International Standards, Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D86 Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric PressureD130 Test Method

8、for Corrosiveness to Copper from Petroleum Products by Copper Strip TestD323 Test Method for Vapor Pressure of Petroleum Products (Reid Method)D873 Test Method for Oxidation Stability of Aviation Fuels (Potential Residue Method)D1094 Test Method for Water Reaction of Aviation FuelsD1298 Test Method

9、for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products byHydrometer MethodD2386 Test Method for Freezing Point of Aviation FuelsD2622 Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence SpectrometryD2624 Test Methods for El

10、ectrical Conductivity of Aviation and Distillate FuelsD2700 Test Method for Motor Octane Number of Spark-Ignition Engine FuelD3237 Test Method for Lead in Gasoline by Atomic Absorption SpectroscopyD3338 Test Method for Estimation of Net Heat of Combustion of Aviation FuelsD4052 Test Method for Densi

11、ty, Relative Density, and API Gravity of Liquids by Digital Density MeterD4057 Practice for Manual Sampling of Petroleum and Petroleum ProductsD4171 Specification for Fuel System Icing InhibitorsD4177 Practice for Automatic Sampling of Petroleum and Petroleum ProductsD4306 Practice for Aviation Fuel

12、 Sample Containers for Tests Affected by Trace Contamination1 This specification is under the jurisdiction ofASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of SubcommitteeD02.J0.02 on Spark and Compression Ignition Aviation Engine Fuels.Curren

13、t edition approved Nov. 1, 2015May 1, 2017. Published November 2015July 2017. Originally approved in 2009. Last previous edition approved in 20142015 asD7547 14b.D7547 151. DOI: 10.1520/D7547-15E01.10.1520/D7547-17.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM C

14、ustomer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to

15、 the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summa

16、ry of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1D4529 Test Method for Estimation of Net Heat of Combustion of Aviation FuelsD4809 Test Method for Heat of Combustion of Liquid Hy

17、drocarbon Fuels by Bomb Calorimeter (Precision Method)D4865 Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel SystemsD5006 Test Method for Measurement of Fuel System Icing Inhibitors (Ether Type) in Aviation FuelsD5059 Test Methods for Lead in Gasoline by X-Ray Spectroscop

18、yD5191 Test Method for Vapor Pressure of Petroleum Products (Mini Method)D6469 Guide for Microbial Contamination in Fuels and Fuel SystemsD7547 172E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications3. Terminology3.1 Definitions:3.1.1 unleaded aviation

19、gasoline, ngasoline possessing specific properties suitable for fueling aircraft powered byreciprocating spark ignition engines, where lead is not intentionally added for the purpose of enhancing octane performance.3.1.1.1 DiscussionPrincipal properties include volatility limits, stability, detonati

20、on-free performance in the engine for which it is intended, andsuitability for low temperature performance.4. Classification4.1 Two grades of unleaded aviation gasoline are provided, known as: Grades UL91 and UL94.3NOTE 1Grades UL91 and UL94 are based on their octane number as measured by Test Metho

21、d D2700 motor method.5. Materials and Manufacture5.1 Unleaded aviation gasoline, except as otherwise specified in this specification, shall consist of blends of refinedhydrocarbons derived from crude petroleum, natural gasoline, or blends, thereof, with synthetic hydrocarbons or aromatichydrocarbons

22、, or both.5.2 AdditivesThese may be added to each grade of unleaded aviation gasoline in the amount and of the composition specifiedin the following list of approved materials. The quantities and types shall be declared by the manufacturer. Additives added afterthe point of manufacture shall also be

23、 declared.5.2.1 AntioxidantsThe following oxidation inhibitors may be added to the gasoline separately, or in combination, in totalconcentration not to exceed 12 mg of inhibitor (not including weight of solvent) per litre of fuel.5.2.1.1 2,6-ditertiary butyl-4-methylphenol.5.2.1.2 2,4-dimethyl-6-ter

24、tiary butylphenol.5.2.1.3 2,6-ditertiary butylphenol.5.2.1.4 75 % minimum 2,6-ditertiary butylphenol plus 25 % maximum mixed tertiary and tritertiary butylphenols.5.2.1.5 75 % minimum di- and tri-isopropyl phenols plus 25 % maximum di- and tri-tertiary butylphenols.5.2.1.6 72 % minimum 2,4-dimethyl-

25、6-tertiary butylphenol plus 28 % maximum monomethyl and dimethyl tertiarybutylphenols.5.2.1.7 N,N-di-isopropyl-para-phenylenediamine.5.2.1.8 N,N-di-secondary-butyl-para-phenylenediamine.5.2.2 Fuel System Icing Inhibitor (FSII)One of the following may be used:5.2.2.1 Isopropyl Alcohol (IPA, propan-2-

26、ol), in accordance with the requirements of Specification D4171 (Type II). May beused in concentrations recommended by the aircraft manufacturer when required by the aircraft owner/operator.3 Supporting data have been filed at ASTM International Headquarters and may be obtained by requesting Researc

27、h Report RR:D02-1526RR:D02-1859. Contact ASTMCustomer Service at serviceastm.org.D7547 173NOTE 2Addition of isopropyl alcohol (IPA) can reduce knock ratings below minimum specification values (see X1.2.3).45.2.2.2 Di-Ethylene Glycol Monomethyl Ether (Di-EGME), conforming to the requirements of Speci

28、fication D4171 (Type III)may be used in concentrations of 0.10 % volume to 0.15 % volume when required by the aircraft owner/operator.5.2.2.3 Test Method D5006 may be used to determine the concentration of Di-EGME in aviation fuels.5.2.3 Electrical Conductivity AdditiveStadis 4505 in concentrations

29、up to 3 mgL is permitted. When loss of fuel conductivitynecessitates retreatment with electrical conductivity additive, further addition is permissible up to a maximum cumulative level of5 mgL of Stadis 450.55.2.4 Corrosion Inhibitor AdditiveThe following corrosion inhibitors may be added to the gas

30、oline in concentrations not toexceed the maximum allowable concentration (MAC) listed for each additive.DCI-4A MAC = 24 g/m3DCI-6A MAC = 15 g/m3HITEC 580 MAC = 22.5 g/m3NALCO 5403 MAC = 22.5 g/m3NALCO 5405 MAC = 11.0 g/m3UNICOR J MAC = 22.5 g/m3SPEC-AID 8Q22 MAC = 24.0 g/m3TOLAD 351 MAC = 24.0 g/m3T

31、OLAD 4410 MAC = 22.5 g/m36. Detailed Requirements6.1 The unleaded aviation gasoline shall conform to the requirements prescribed in Table 1.6.2 Test results shall not exceed the maximum or be less than the minimum values specified in Table 1. No allowance shall bemade for the precision of the test m

32、ethods. To determine the conformance to the specification requirement, a test result may berounded to the same number of significant figures as in Table 1 using Practice E29. Where multiple determinations are made, theaverage result, rounded according to Practice E29, shall be used.7. Workmanship, F

33、inish, and Appearance7.1 The unleaded aviation gasoline specified in this specification shall be free from undissolved water, sediment, and suspendedmatter. The odor of the fuel shall not be nauseating or irritating. No substances of known dangerous toxicity under usual conditionsof handling and use

34、 shall be present.8. Sampling8.1 Because of the importance of proper sampling procedures in establishing fuel quality, use the appropriate procedures inPractice D4057 or Practice D4177.8.1.1 Although automatic sampling following Practice D4177 may be useful in certain situations, initial refinery sp

35、ecificationcompliance testing shall be performed on a sample taken following procedures in Practice D4057.8.2 A number of unleaded aviation gasoline properties, including copper corrosion, electrical conductivity, and others are verysensitive to trace contamination which can originate from sample co

36、ntainers. For recommended sample containers, refer to PracticeD4306.9. Report9.1 The type and number of reports to ensure conformance with the requirements of this specification shall be mutually agreedto by the purchaser and the supplier of the unleaded aviation gasoline.10. Test Methods10.1 The re

37、quirements enumerated in this specification shall be determined in accordance with the following ASTM testmethods:10.1.1 Knock Value (MON)Test Method D2700.10.1.2 DensityTest Methods D1298 or D4052.10.1.3 DistillationTest Method D86.10.1.4 Vapor PressureTest Methods D323 or D5191.10.1.5 Freezing Poi

38、ntTest Method D2386.10.1.6 SulfurTest Method D2622.10.1.7 Net Heat of CombustionTest Methods D4529, D3338, or D4809.10.1.8 Corrosion (Copper Strip)Test Method D130, 2 h test at 100 C in bomb.4 Supporting data have been filed at ASTM International Headquarters and may be obtained by requesting Resear

39、ch Report RR:D02-1526.5 Stadis is a registered trademark marketed by Innospec, Inc., Innospec Manufacturing Park, Oil Sites Road, Ellesmere Port, Cheshire, CH65 4EY, UK.D7547 17410.1.9 Potential GumTest Method D873 except that wherever the letter X occurs (referring to oxidation time) insert thenumb

40、er 5, designating the number of hours prescribed in this specification.10.1.10 Water ReactionTest Method D1094.10.1.11 Electrical ConductivityTest Method D2624.10.1.12 Lead ContentTest Method D3237 and D5059.11. Keywords11.1 Avgas; aviation gasoline; gasoline; unleaded Avgas; unleaded aviation gasol

41、ineTABLE 1 Detailed Requirements for Unleaded Aviation GasolinesAGradeUL91GradeUL94 ASTM Test MethodBPropertyCOMBUSTIONOctane RatingKnock value, Motor Octane NumberC min 91.0 94.0 D2700Net heat of combustion, MJ/kgD min 43.5 43.5 D4529 or D3338Net heat of combustion, MJ/kgC min 43.5 43.5 D4529 or D3

42、338Octane RatingKnock value, Motor Octane NumberD min 91.0 94.0 D2700COMPOSITIONSulfur, mass percent max 0.05 0.05 D2622Tetraethyl lead, g Pb/L max 0.0130 0.0130 D3237 or D5059Requirements for All GradesVOLATILITYVapor pressure, 38 C, kPa minmax38.049.0D323 or D5191EDensity at 15 C, kg/m3 Report D12

43、98 or D4052Distillation, C D86Initial boiling point ReportFuel Evaporated10 volume percent at C max 7540 volume percent at C min 7550 volume percent at C max 10590 volume percent at C max 135Final boiling point max 170Sum of 10 % + 50 % evaporated tem-peraturesmin 135Recovery volume percent min 97Re

44、sidue volume percent max 1.5Loss volume percent max 1.5FLUIDITYFreezing point, C max 58F D2386CORROSIONCopper strip, 2 h at 100 C max No. 1 D130CONTAMINANTSOxidation stability, mg/100 mL(5 h aging)GD873Potential gum max 6Lead precipitate max 3Water reaction D1094Volume change, mL max 2OTHERElectrica

45、l conductivity, pS/m max 450H D2624A For compliance of test results against the requirements of Table 1, see 6.2.B The test methods indicated in this table are referred to in Section 10.C Knock ratings shall be reported to the nearest 0.1 octane/performance number.C For all grades use either Eq 1 or

46、 Table 1 in Test Method D4529 or Eq 2 in Test Method D3338. Test Method D4809 may be used as an alternative. In case of dispute,Test Method D4809 shall be used.D Knock ratings shall be reported to the nearest 0.1 octane/performance number.E Test Method D5191 shall be the referee vapor pressure metho

47、d.F If no crystals have appeared on cooling to 58 C, the freezing point may be reported as less than 58 C.G If mutually agreed upon between the purchaser and the supplier, a 16 h aging gum requirement may be specified instead of the 5 h aging gum test; in such case thegum content shall not exceed 10

48、 mg/100 mL and the visible lead precipitate shall not exceed 4 mg/100 mL. In such fuel the permissible antioxidant shall not exceed 24mg/L.H Applies only when an electrical conductivity additive is used; when a customer specifies fuel containing conductivity additive, the following conductivity limi

49、ts shall applyunder the condition at point of use:Minimum 50 pS/mMaximum 450 pS/m.The supplier shall report the amount of additive added.D7547 175APPENDIX(Nonmandatory Information)X1. PERFORMANCE CHARACTERISTICS OF UNLEADED AVIATION GASOLINEX1.1 IntroductionX1.1.1 Unleaded aviation gasoline is a complex mixture of relatively volatile hydrocarbons that vary widely in their physical andchemical properties. The engines and aircraft impose a variety of mechanical, physical, and chemical environments. The propertiesof unleaded avia