ASTM D7574-2016 9568 Standard Test Method for Determination of Bisphenol A in Environmental Waters by Liquid Chromatography Tandem Mass Spectrometry《采用液相色谱法 串联质谱法测定环境水体中双酚A的标准试验方法》.pdf

1、Designation: D7574 16Standard Test Method forDetermination of Bisphenol A in Environmental Waters byLiquid Chromatography/Tandem Mass Spectrometry1This standard is issued under the fixed designation D7574; the number immediately following the designation indicates the year oforiginal adoption or, in

2、 the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This procedure covers the determination of bisphenol A(BPA) extracted from water ut

3、ilizing solid phase extraction(SPE), separated using liquid chromatography (LC) and de-tected with tandem mass spectrometry (MS/MS). BPA isqualitatively and quantitatively determined by this method.This method adheres to multiple reaction monitoring (MRM)mass spectrometry.1.2 The values stated in SI

4、 units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 The method detection limit (MDL) and reporting limit(RL) for BPA are listed in Table 1.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is

5、theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D1129 Terminology Relating to WaterD1193 Specification for Reagent WaterD2777 Practi

6、ce for Determination of Precision and Bias ofApplicable Test Methods of Committee D19 on WaterD3694 Practices for Preparation of Sample Containers andfor Preservation of Organic ConstituentsD3856 Guide for Management Systems in LaboratoriesEngaged in Analysis of WaterD5847 Practice for Writing Quali

7、ty Control Specificationsfor Standard Test Methods for Water AnalysisD5905 Practice for the Preparation of Substitute Wastewater2.2 Other Documents:3The Code of Federal Regulations 40 CFR Part 136, Appen-dix B3. Terminology3.1 Definitions:3.1.1 For definitions of terms used in this standard, refer t

8、oTerminology D1129.3.2 Definitions of Terms Specific to This Standard:3.2.1 environmental water, nshall refer to water testedusing this method. See Section 5.3.2.2 independent reference material, IRM, na material ofknown purity and concentration obtained either from theNational Institute of Standard

9、s andTechnology (NIST) or otherreputable supplier. The IRM shall be obtained from a differentlot of material than is used for calibration.3.3 Acronyms:3.3.1 CCC, nContinuing Calibration Check3.3.2 IC, nInitial Calibration3.3.3 LC, nLiquid Chromatography3.3.4 LCS/LCSD, nLaboratory Control Sample/Labo

10、ratory Control Sample Duplicate3.3.5 MDL, nMethod Detection Limit3.3.6 MeOH, nMethanol3.3.7 mM, nmillimolar,110-3moles/L3.3.8 MRM, nMultiple Reaction Monitoring3.3.9 MS/MSD, nMatrix Spike/Matrix Spike Duplicate3.3.10 NA, adjNot Available3.3.11 ND, nnon-detect3.3.12 P liquid chromatography; solid pha

11、se ex-traction; tandem mass spectrometry; waterASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights,

12、and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revi

13、sion of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you

14、shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be o

15、btained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 1610