ASTM D7655 D7655M-2012(2017) 6875 Standard Classification for Size of Aggregate Used as Ballast for Membrane Roof Systems《用作膜屋面系统镇流器的集料尺寸的标准分类》.pdf

1、Designation: D7655/D7655M 12 (Reapproved 2017)Standard Classification forSize of Aggregate Used as Ballast for Membrane RoofSystems1This standard is issued under the fixed designation D7655/D7655M; the number immediately following the designation indicates theyear of original adoption or, in the cas

2、e of revision, the year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This classification defines the aggregate size designa-tions and ranges in mechanical analy

3、ses for standard sizes ofaggregate used as ballast for membrane roof systems.1.2 The text of this classification references notes andfootnotes which provide explanatory material. These notes andfootnotes (excluding those in tables and figures) shall not beconsidered as requirements of the standard.1

4、.3 With regard to sieve sizes and the size of aggregate asdetermined by the use of testing sieves, the values in inch-pound units are shown for the convenience of the user;however, the standard sieve designations shown in parenthesesis the standard value as stated in Specification E11.1.4 The values

5、 stated in either SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.1

6、.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.

7、1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to

8、 Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2C136/C136M Test Method for Sieve Analysis of Fine andCoarse AggregatesD75/D75M Practice for Sampling AggregatesD1079 Terminology Relating to Roofing and WaterproofingE11 Specification for Woven Wire Test Sieve Cloth and TestSieves2.2

9、ANSI/SPRI Standard:3RP-4 Wind Design Standard for Ballasted Single-ply Roof-ing Systems3. Terminology3.1 DefinitionsFor definitions of terms used in thisspecification, refer to Terminology D1079.4. Significance and Use4.1 The wind resistance of ballasted membrane roof systemsis determined largely by

10、 the size and weight of the ballastedused. ANSI/SPRI RP-4 provides a method for the wind designof ballasted single-ply membrane roof systems and includesspecific guidelines for the size and weight of aggregate used asballast. The aggregate size classifications provided in thisstandard are intended f

11、or use with the guidelines providedANSI/SPRI RP-4 in designing the wind resistance of aggregateballasted single-ply membrane roof systems.4.2 The aggregate size classifications provided in this clas-sification are intended to provide a basis of compliance forcontract documentsthat specify certain ag

12、gregate sizes for useon ballasted membrane systems.1This classification is under the jurisdiction of ASTM Committee D08 onRoofing and Waterproofing and is the direct responsibility of Subcommittee D08.20on Roofing Membrane Systems.Current edition approved Nov. 1, 2017. Published December 2017. Origi

13、nallyapproved in 2012. Last previous edition approved in 2012 as D7655/D7655M 12.DOI:10.1520/D7655_D7655M-12R17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the

14、standards Document Summary page onthe ASTM website.3Available from SPRI, 411 Waverley Oaks Road, Suite 331B, Waltham, MA02452.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with

15、internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.15. Manufacture5.1 The standard sizes of agg

16、regate described in this clas-sification are manufactured by means of any suitable processused to separate raw material into the desired size ranges.Production of standard sizes by blending two or more differentcomponents is permitted.6. Standard Sizes6.1 Standard sizes of aggregate shall comply wit

17、h the sizesgiven in Table 1. All sizes shall be determined by means oflaboratory sieves having square openings and conforming toSpecification E11.TABLE 1 Standard Sizes of Processed AggregateSizeNumberNominal Size,Square OpeningsAmounts Finer than Each Laboratory Sieve (Square Openings), mass percen

18、t100-mm4-in.90-mm312-in.75-mm3-in.63-mm212-in.50-mm2-in.37.5-mm112-in.25.0-mm1-in.19.0-mm34-in.12.5-mm12-in.9.5-mm38-in.1 90 to 37.5-mm312 to 112-in.100 90 to 100 . 25 to 60 . 0 to 15 . 0 to 5 . .2 63 to 37.5-mm212 to 112-in. . 100 90 to 100 35 to 70 0 to 15 . 0 to 5 . .3 50 to 25-mm2 to 1-in. . . 1

19、00 90 to 100 0 to 15 . . 0 to 5 .4 37.5 to 19-mm112 to34-in. . 100 90 to 100 20 to 55 0 to 15 . 0 to 57. Basis of Classification7.1 Classification is based upon the size number and sizeranges shown in Table 1 with the aggregate sampled inaccordance with Practice D75/D75M and tested for grading byTes

20、t Method C136/C136M.8. Keywords8.1 aggregate; aggregate standard size; screeningsASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the va

21、lidity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your co

22、mments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments hav

23、e not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple

24、 copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 12 (2017)2