ASTM D7802-2012 7500 Standard Terminology for Paint Roller Application Tools《油漆辊使用工具的标准术语》.pdf

1、Designation: D7802 12Standard Terminology forPaint Roller Application Tools1This standard is issued under the fixed designation D7802; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parenthes

2、es indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This standard establishes the definitions or terminologyused in the manufacturing and testing of paint rollers.1.2 This standard does not purport to addre

3、ss all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D5069 Practice

4、for Preparation of Paint-Roller Covers forEvaluation of Architectural CoatingsD6337 Practice for Physical Characterization of WovenPaint Applicator FabricsD7073 Guide for Application and Evaluation of Brush andRoller Applied Paint Films3. Terminology3.1 Definitions:fabric, nfor paint applicators, a

5、paint carrying medium madeby knitting or weaving; fabrics may consist of synthetic ornatural materials, or a combination of both.formulation, na specification that gives ingredients andamounts, or process.matting, nfor fabric fibers, a condition where they tend to lieflat during application.nap, nfo

6、r fabric fibers, the length of fibers essentiallyperpendicular to the surface.pick-up, nfor paint applicators, after break-in, the amount ofpaint, or other coating material, an applicator can hold.release, nfor paint applicators, after break-in, the amount ofpaint, or other coating materials, that t

7、he applicator candispense after pick up.sliver knitting, na process for producing an array of fiberslocked essentially perpendicular to a knit backing.wet edge time, nthe length of time a wet, coated region canstand before showing lap marks when an overlapped regionis coated; this is also known as w

8、et edge retention.4. Keywords4.1 definitions; fabric; terminologyASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any su

9、ch patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invit

10、ed either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a

11、 fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this

12、 standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).1Th

13、is terminology is under the jurisdiction of ASTM Committee on Paint andRelated Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.61 on Paint Application Tools.Current edition approved June 1, 2012. Published June 2012. DOI: 10.1520/D7802-12.2For referenced AST

14、M standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1