ASTM D7802-2012(2016) 9998 Standard Terminology for Paint Roller Application Tools《油漆辊使用工具的标准术语》.pdf

1、Designation: D7802 12 (Reapproved 2016)Standard Terminology forPaint Roller Application Tools1This standard is issued under the fixed designation D7802; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A n

2、umber in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This standard establishes the definitions or terminologyused in the manufacturing and testing of paint rollers.1.2 This standard does no

3、t purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standard

4、s:2D5069 Practice for Preparation of Paint-Roller Covers forEvaluation of Architectural CoatingsD6337 Practice for Physical Characterization of WovenPaint Applicator FabricsD7073 Guide for Application and Evaluation of Brush andRoller Applied Paint Films3. Terminology3.1 Definitions:fabric, nfor pai

5、nt applicators, a paint carrying medium madeby knitting or weaving; fabrics may consist of synthetic ornatural materials, or a combination of both.formulation, na specification that gives ingredients andamounts, or process.matting, nfor fabric fibers, a condition where they tend to lieflat during ap

6、plication.nap, nfor fabric fibers, the length of fibers essentiallyperpendicular to the surface.pick-up, nfor paint applicators, after break-in, the amount ofpaint, or other coating material, an applicator can hold.release, nfor paint applicators, after break-in, the amount ofpaint, or other coating

7、 materials, that the applicator candispense after pick up.sliver knitting, na process for producing an array of fiberslocked essentially perpendicular to a knit backing.wet edge time, nthe length of time a wet, coated region canstand before showing lap marks when an overlapped regionis coated; this

8、is also known as wet edge retention.4. Keywords4.1 definitions; fabric; terminologyASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the

9、validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your

10、comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments h

11、ave not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multip

12、le copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Cent

13、er, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ terminology is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.61 on Paint Application Tools.Current edition approved Dec.

14、1, 2016. Published December 2016. Originallyapproved in 2012. Last previous edition approved in 2012 as D7802 12. DOI:10.1520/D7802-12R16.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume

15、information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1