ASTM E1119-2009(2015) Standard Specification for Industrial Grade Ethylene Glycol《工业级乙二醇的标准规格》.pdf

1、Designation: E1119 09 (Reapproved 2015)Standard Specification forIndustrial Grade Ethylene Glycol1This standard is issued under the fixed designation E1119; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision.

2、 A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This specification covers industrial grade et

3、hylene gly-col.1.2 Review the current Materials Safety Data Sheets(MSDS) for detailed information concerning toxicity, first aidprocedures, handling and safety precautions.1.3 The following applies to all specified limits in thisstandard; for purposes of determining conformance with thisstandard, an

4、 observed value or a calculated value shall berounded off “to the nearest unit” in the last right-hand digitused in expressing the specification limit, in accordance withthe rounding-off method of Practice E29.1.4 The values stated in SI units are to be regarded asstandard. No other units of measure

5、ment are included in thisstandard.1.5 The following safety hazards caveat pertains only to thetest methods portion, Section 5, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this stand

6、ard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2D482 Test Method for Ash from Petroleum ProductsD1078 Test Method for Distillation Range of Volatile Or-ganic LiquidsD1209 Test M

7、ethod for Color of Clear Liquids (Platinum-Cobalt Scale)D1722 Test Method for Water Miscibility of Water-SolubleSolventsD4052 Test Method for Density, Relative Density, and APIGravity of Liquids by Digital Density MeterE29 Practice for Using Significant Digits in Test Data toDetermine Conformance wi

8、th SpecificationsE202 Test Methods for Analysis of Ethylene Glycols andPropylene GlycolsE300 Practice for Sampling Industrial ChemicalsE1064 Test Method for Water in Organic Liquids by Coulo-metric Karl Fischer TitrationE2409 Test Method for Glycol Impurities in Mono-, Di-, Tri-and Tetraethylene Gly

9、col and in Mono- and DipropyleneGlycol(Gas Chromatographic Method)E2679 Test Method for Acidity in Mono-, Di-, Tri- andTetraethylene Glycol byNon-Aqueous PotentiometricTitrationE2680 Test Method for Appearance of Clear, TransparentLiquids (Visual Inspection Procedure)3. Requirements3.1 Industrial gr

10、ade ethylene glycol shall conform to thespecification chemical and physical requirements (see Table 1).4. Sampling4.1 Sample ethylene glycol in accordance with the appro-priate sections of Practice E300 for liquid samples.5. Test Methods5.1 Test each composite sample for chemical and physicalrequire

11、ments using the test methods specified in 3.1. Many ofthese methods, along with alternative test methods andtechnologies, can be found in Test Methods E202. In case of adispute, test methods identified in 3.1 of this specification shallbe the preferred test method.6. Packaging, Package Markings, and

12、 Transportation6.1 The packaging, labeling, and transportation of commer-cial quantities shall conform to applicable federal, state, andlocal regulation. Conformance is the responsibility of themanufacturer and the shipper.7. Keywords7.1 ethylene glycol; industrial grade1This specification is under

13、the jurisdiction of ASTM Committee E15 onIndustrial and Specialty Chemicals and is the direct responsibility of SubcommitteeE15.02 on Product Standards.Current edition approved June 1, 2015 Published June 2015. Originally approvedin 1986. Last previous edition approved in 2009 as E1119 09. DOI: 10.1

14、520/E1119-09R15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the

15、end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1SUMMARY OF CHANGESCommittee E15 has identified the location of selected changes to this standard since the last issue (E1119-07)that may impact the use of this standa

16、rd.(1) Replaced two Standard Test Methods within the specifica-tion with test methods that have been recently adopted by E15and reflect newer technologies used in the industry.(2) Section 2, Referenced Documents, was updated.(3) Table 1, Chemical and Physical SpecificationRequirements, was updated.A

17、STM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are

18、entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standard

19、sand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committe

20、e on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress o

21、r at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 1 Chemical and

22、 Physical Specification RequirementsSpecification Requirements min max ASTM Test MethodAcidity as Acetic Acid, % mass (m/m) 0.005 E2679Appearance, Clear & Free from Suspended Matter pass E2680Color, platinum cobalt 10 D1209GlycolsEthylene glycol, % mass (m/m)Diethylene glycol, % mass (m/m)Other glyc

23、ols, % mass (m/m)99.00.60.1E2409Water, % mass (m/m) 0.3 E1064Typical Properties min max ASTM Test MethodAsh, % mass (m/m) 0.005 D482Distillation RangeInitial Boiling Point, CDry Point, C193204D1078Relative Density at20/20 Cor25/25 C1.1151or1.11291.1156or1.1134D4052Water Miscibility miscible D1722E1119 09 (2015)2