ASTM E1403-1997(2013) Standard Specification for Laboratory Glass Boiling Flasks《实验室玻璃烧瓶的标准规范》.pdf

1、Designation: E1403 97 (Reapproved 2013)Standard Specification forLaboratory Glass Boiling Flasks1This standard is issued under the fixed designation E1403; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision.

2、A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification provides standard dimensional re-quirements for flat-bottom and round-bottom glass boilingflasks.NOTE 1For packagi

3、ng standards, choose among the followingstandards, E920, E921, E1133, and E1157.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.2. Referenced Documents2.1 ASTM Standards:2E438 Specification for Glasses in Laboratory Apparatu

4、sE671 Specification for Maximum Permissible Thermal Re-sidual Stress in Annealed Glass Laboratory ApparatusE676 Specification for Interchangeable Taper-Ground JointsE677 Specification for Interchangeable Spherical GroundJointsE920 Specification for Commercially Packaged LaboratoryApparatusE921 Speci

5、fication for Export Packaged Laboratory Appa-ratusE1133 Practice for Performance Testing of Packaged Labo-ratory Apparatus for United States Government Procure-mentsE1157 Specification for Sampling and Testing of ReusableLaboratory Glassware3. Classification3.1 Boiling flasks shall be in the followi

6、ng types and sizes.3.1.1 Type IFlat bottomed3.1.1.1 Class 1Tooled top; long neck in the followingsizes: 50 mL, 125 mL, 250 mL, 500 mL, 1 000 mL, 2 000 mL,3 000 mL, 6 000 mL, and 12 000 mL.3.1.1.2 Class 2Ring neck, long neck in the followingsizes: 500 mL, 1 000 mL, 2 000 mL, 6 000 mL, and 12 000 mL.3

7、.1.1.3 Class 3Ring neck, long neck, wicker protector inthe following size: 500 mL and 1000 mL.3.1.1.4 Class 4Standard Taper $neck, short neck in thefollowing sizes: 50 mL, 125 mL, 250 mL, 300 mL, 500 mL,and 1000 mL.3.1.1.5 Class 5Standard Taper $neck, long neck in thefollowing sizes: 250 mL, 500 mL,

8、 and 1000 mL.3.1.2 Type IIRound Bottomed3.1.2.1 Class 1Tooled top, long neck in the followingsizes: 25 mL, 50 mL, 100 mL, 250 mL, 500 mL, 1000 mL,2000 mL, 5000 mL, and 6000 mL.3.1.2.2 Class 2Ring neck, short neck in the followingsizes: 250 mL, 500 mL, 1 000 mL, 2 000 mL, 3 000 mL, 5 000mL, 12 000 mL

9、, and 22 000 mL.3.1.2.3 Class 3Standard Taper $neck, short neck in thefollowing sizes: 5 mL, 10 mL, 25 mL, 50 mL, 100 mL, 250mL, 500 mL, 1 000 mL, 2 000 mL, 3 000 mL, 5 000 mL, and12 000 mL.3.1.2.4 Class 4Standard Taper $neck, long neck in thefollowing sizes: 100 mL, 250 mL, 500 mL, and 1000 mL.3.1.

10、2.5 Class 5Standard Taper $neck, short neck withside arm in the following sizes: 250 mL and 300 mL.3.1.2.6 Class 6Standard Taper $neck, short neck withthermometer well in the following sizes: 500 mL, 1000 mL,and 2000 mL.3.1.2.7 Class 7Ball and socket $neck, short neck in thefollowing sizes 250 mL, 5

11、00 mL, 1000 mL, and 2000 mL.3.1.3 Type IIIHeart-shape bottomed3.1.3.1 Class 1Standard Taper $neck, short neck in thefollowing sizes: 5 mL, 10 mL, 25 mL, 50 mL, and 100 mL.NOTE 2The term millilitre (mL) is commonly used as a special namefor the cubic centimetre (cm3) and similarly the litre (L) for 1

12、000 cubiccentimetres, in accordance with the International System of Units (SI).4. Material and Annealing4.1 Flasks shall be made of borosilicate glass conforming tothe requirement of Type I, Class A of Specification E438.4.2 Maximum residual thermal stress shall be such as toconform to Specificatio

13、n E671.1This specification is under the jurisdiction of ASTM Committee E41 onLaboratory Apparatus and is the direct responsibility of Subcommittee E41.01 onApparatus.Current edition approved Nov. 1, 2013. Published December 2013. Originallyapproved in 1991. Last previous edition approved in 2008 as

14、E1403 97 (2008).DOI: 10.1520/E1403-97R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM Inter

15、national, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15. Appearance5.1 The general appearance of the flasks shall be as illus-trated in Fig. 1.6. Design6.1 Necks on all single-neck flasks shall be circular in crosssection and perpendicular to the center of the

16、 flask body. Necklengths may be designated “short” or “long”.6.2 The top shall be strengthened and finished.6.2.1 Vial finish or tooled top6.2.2 Beaded rim or ring neck6.2.3 Standard taper ground glass joint in compliance withSpecification E6766.2.4 Ball and socket ground glass joint, in compliance

17、withSpecification E6776.3 Wall thickness minimums are given for all flasks inTable 1.6.4 Flat bottoms shall be in a plane perpendicular to thevertical axis through the neck of the flask.6.4.1 The bottom of the flask shall be flat, however veryslight concavity is permitted. The flasks shall stand ver

18、ticallywithout rocking or spinning when placed on a level surface.6.4.2 The diameter of the flat base of the flask shall be 45 to65 % of the maximum external diameter.6.4.3 Type I, Class 3 flat-bottomed flasks shall have awoven wicker insulation collar around the neck.6.5 Round-bottomed flasks shall

19、 be spherical in shape to thepoint of juncture with the flask neck.6.5.1 Type II, Class 5 round-bottom flasks shall have aside-arm opening to accommodate a thermometer or bleed tubeinto the interior of the flask content.6.5.2 Type II, Class 6 round-bottom flasks shall have athermometer well within t

20、he flask but not open to the contentof the flask.6.6 Heart-shape-bottomed flasks (sometimes called pearshaped) shall be shaped to concentrate small amounts of liquidin the bottom center of the flask.7. Capacity and Dimensions7.1 The nominal capacity of a flask shall not exceed theactual capacity to

21、the base of the neck. Dimensions shallconform to the requirements of Table 1.8. Sampling and Testing8.1 See Specification E1157.9. Product Marking9.1 Each flask shall be permanently marked with the nameor known trademark of the manufacturer and the nominalcapacity. If applicable, the standard taper

22、or ball and socketjoint size shall be marked on each flask.9.2 There shall be an area on one side of the flask formarking with a pencil.10. Packaging and Package Marking10.1 Select from one of Specifications E920, E921, andPractice E1133.11. Keywords11.1 boiling; flasks; glassFIG. 1 General Appearan

23、ce of FlasksTABLE 1 Capacity and Dimensions for Glass Boiling FlaskNominalcapacity,mLOutsideDiameterBodyWidestPoint max,mmStopperAsizeOverall HeightMaximumWithout StopperWallthicknessBmin, mmFlatbottom,mmRoundbottom,mmHeart-shapedbottom,mm5 26 . . 52 55 0.810 32 . . 60 65 0.825 43 1 . 92 80 0.850 52

24、 1 103 108 99 0.8100 66 2 113 122 117 0.8125 70 2 or 3 122 . . 0.8200 76 5 . 130 . 0.8250 87 5 150 155 . 0.8300 89 5 150 155 . 0.8500 107 6 190 210 . 0.81000 134 8 220 250 . 0.82000 170 8 or 10 295 315 . 1.13000 192 9 or 10 333 260 . 1.45000 223 11 . 390 . 1.56000 239 11 375 360 . 1.812000 298 11 39

25、5 385 . 2.022000 352 14 . 432 . 2.5ARubber stopper style only.BNeck seal zones may be a minimum of 70 % of these values.E1403 97 (2013)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this stan

26、dard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and

27、if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, w

28、hich you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959

29、,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).E1403 97 (2013)3