ASTM E1638-2007 Standard Terminology Relating to Sieves Sieving Methods and Screening Media《过滤、筛分法和筛网标准术语》.pdf

1、Designation: E 1638 07Standard TerminologyRelating to Sieves, Sieving Methods and Screening Media1This standard is issued under the fixed designation E 1638; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision

2、 A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.INTRODUCTIONParticle size distribution analysis through the use of standard testing sieves has been a commonlyadopted method of verifying comp

3、liance with desired process particle specifications for manydecades. As an adjunct to that function, greater emphasis is being placed on inter- and intralaboratorycorrelation of all particle measurement systems, testing sieves included.To ensure a better understanding of the comparison of testing re

4、sults from sieve analysis-basedparticle measurement systems, terminology common to the process must be documented and definedso that both the recipient and generator of the data are in full agreement as to the meaning of the data.Every effort has been made to ensure accuracy, precision, and clarity

5、for the terms included in thisterminology. For Committee E29, this is an on-going process with new terms being developed forfuture inclusion. Suggestions and comments for additions, corrections, and revisions are welcomed.1. Scope1.1 This terminology covers terms used in the descriptionand procedure

6、 of analysis of the size of particulate materialsthrough sieve analysis with standard testing sieves. The termsrelate directly to the equipment used in the analysis, thephysical forms of the material to be sieved may take on before,during, or after analysis, and selected descriptive data reduc-tion

7、and analysis formats.1.2 Committee E29 on Particle Size Measurement feels thatit is essential to include terms and definitions explicit to thescope, regardless of whether the terms appear in existingASTM standards. Terms that are in common usage and appearin common-language dictionaries are generall

8、y not included.2. Referenced Documents2.1 ASTM Standards:2ASTM STP 447B Manual on Testing Seiving Methods2.2 ISO Standard:3ISO 2395 Test Sieves and Test SievingVocabulary.3. Significance and Use3.1 This terminology contains terms used in the descriptionand procedure of analysis of the size of partic

9、ulate materialsthrough sieve analysis with standard testing sieves and isapplicable to the work of many ASTM technical committees.For a composite listing of published ASTM standards usingstandard testing sieves, Refer to ASTM STP 447B.3.2 While some of the terms appearing in this terminologymay also

10、 be used in the description, procedure, and endproducts of production screening (either on a batch-fed orcontinuous basis), it is the intent of this terminology to presentthe definitions and usage of terms strictly in the context ofsieve analysis using standard testing sieves.4. Terminology4.1 Defin

11、itions:agglomerate, ntwo or more particles adhering together.aperture size, nthe dimension defining an opening in ascreening or sieving medium.bulk density, nthe mass per unit volume of a material,including voids inherent in the material as tested.cumulative oversize distribution graph, na graph obt

12、ainedby plotting the total (cumulative) percentage by the massretained on each of a set of sieves versus the correspondingaperture sizes.cumulative undersize distribution graph, na graph ob-tained by plotting the total (cumulative) percentage by themass passing each of a set of sieves versus the cor

13、respondingaperture sizes.1This terminology is under the jurisdiction ofASTM Committee E29 on Particleand Spray Characterization and is the direct responsibility of Subcommittee E29.01on Sieves, Sieving Methods, and Screening Media.Current edition approved June 1, 2007. Published July 2007. Originall

14、y approvedin 1994. Last previous edition approved in 2004 as E 1638 94 (2004).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page on

15、the ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.matched test sieve, na test sieve that reproduces theperforma

16、nce results of a calibration sieve within definedlimits for a designated material.median particle size, nthe particle size at which half thedistribution (by mass, volume, number, etc.) is larger thanand half smaller than the stated size.mesh, nThe number of wires or openings per linear inch or25.4 m

17、illimeters, counted from the center of any wire to apoint exactly one inch or 25.4 millimeters distant, includingthe fractional distance between either thereof.near size particle, na particle of a size approximately equalto the aperture size of the sieve. ISO/DIS 2395open area, nthe ratio of the tot

18、al area of the apertures to thetotal area of the sieving or screening media, expressed as apercentage.particle size distribution, nin sieve analysis, the percent-ages, by mass or number, of all fractions into which varioussizes of particles are classified.representative sample, na sample taken from

19、a quantity ofmaterial that exhibits the characteristics of the originalmaterial from which it was taken.sample, na portion, or part, of a quantity of material.sieve, na plate, sheet, or woven wire cloth, or other device,with regularly spaced apertures of uniform size, mounted ina suitable frame or h

20、older, for use in separating materialaccording to size. The terms sieve and screen can be usedinterchangeably.sieve analysis, nthe act of obtaining a particle size distribu-tion using test sieves.test sample, na quantity of material required for use directlyin a testing procedure.test sieve, na siev

21、e that meets all of the minimum require-ments of ASTM Committee E11.5. Keywords5.1 particle measurement; particle size; particles; particu-late; screen; screening; sieve; sieve analysis; standard testingsieveThis standard is subject to revision at any time by the responsible technical committee and

22、must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of

23、theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C

24、700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).E1638072