ASTM E2064-2000(2006) Standard Guide for Minimum Continuing Education of Individuals Involved in Psychophysiological Detection of Deception (PDD)《与诈骗心理检测(PDD)相关职业的短期连续教育的标准导则》.pdf

1、Designation: E 2064 00 (Reapproved 2006)Standard Guide forMinimum Continuing Education of Individuals Involved inPsychophysiological Detection of Deception (PDD)1This standard is issued under the fixed designation E 2064; the number immediately following the designation indicates the year oforiginal

2、 adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide establishes the minimum amount of ad-vanced continuing

3、education required for individuals engagedin psychophysiological detection of deception (PDD) exami-nations.2. Referenced Documents2.1 ASTM Standards:2E 2000 Guide for Minimum Basic Education and Trainingof Individuals Involved in the Detection of Deception(PDD)3. Terminology3.1 basic PDD trainingth

4、e initial training required toadminister PDD (Polygraph) Examinations in accordance withGuide E 2000.3.2 continuing education trainingadvanced polygraphtraining and education completed after the basic training hasbeen accomplished.3.3 primary polygraph curriculumadvanced training inthe areas of poly

5、graph methodology and techniques such asinstrumentation, chart analysis, test question construction,interviewing, and testing techniques.3.4 secondary polygraph curriculumtraining inpolygraph-related areas such as law, psychology, physiology,research, and other areas, which relate to PDD activities.

6、 Thesemay include, but are not limited to:3.4.1 Computer courses, which may relate to PDD, such as,word processing, small business administration, accounting,and other appropriate areas.4. Significance and Use4.1 This guide is intended to ensure that those individualswho are practicing PDD (polygrap

7、h) examinations maintaintheir proficiency in the profession. Changes are constantlybeing made in the areas of instrumentation, testing format, andprocedures, as well as legislation which affects the conduct ofthe industry. It is important that the individual PDD examinerbe aware of changes in techno

8、logy.5. Minimum Requirements for Advanced ContinuingEducation PDD Training5.1 The required number of minimum hours of training tomaintain professional competence is 40 h, every two calendaryears, starting with the date on which the basic PDD (poly-graph) training was completed.5.2 A minimum of 20 h

9、of continuing education trainingmust be in the primary area of instruction, and up to 20 h maybe in the secondary area of instruction. A normal classroomcontact hour is 50 consecutive min.5.3 All continuing education must be documented in theform of a certificate, diploma, continuing education units

10、(CEU) certificate, or letter transcript setting forth the followingminimum information:5.3.1 Name, address, and location of the training.5.3.2 Name of the instructor or instructor(s) providing theinstruction along with a resume of the instructor(s).5.3.3 Date(s) of training and name of the person re

11、ceivingthe training.5.3.4 Number of hours of training broken down by curricu-lum or subject matter and appropriate course outline(s).6. Sources for Advanced Continuing PDD Training6.1 Acceptable PDD (polygraph) advanced training may beobtained from any of the following areas:6.1.1 Any formal PDD (po

12、lygraph) school meeting thecriteria for Basic Polygraph Training in accordance with GuideE 2000.6.1.2 Any recognized national or state polygraph associa-tion.6.1.3 Any accredited college or university offering formalcourses which are related to PDD curriculum areas.6.1.4 Advanced related courses whi

13、ch are presented at anyformal police department or police training academy or similargroup.1This guide is under the jurisdiction of ASTM Committee E52 on ForensicPsychophysiology and is the direct responsibility of Subcommittee E52.04 onExaminer Education and Training.Current edition approved Dec. 1

14、, 2006. Published February 2007. Originallyapproved in 2000. Last previous edition approved in 2000 as E 2064 00.2Annual Book of ASTM Standards, Vol 14.02.For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMS

15、tandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6.1.5 Advanced related courses which are presented by anyfederal investigative agency, feder

16、al government agency, orU.S. military department which are related to PDD testing.6.1.6 Other training which is directly related to PDD inwhich the instructor(s) are qualified and recognized PDD(polygraph) examiners in the area in which the instruction ispresented.7. Keywords7.1 advanced PDD trainin

17、g; continuing education; forensicpsychophysiology; PDD examinations; polygraph examinerASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of

18、the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Y

19、our comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your commen

20、ts have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).E 2064 00 (2006)2