ASTM E2908-2012(2018) Standard Guide for Fire Prevention for Photovoltaic Panels Modules and Systems《光伏板、模块和系统防火标准指南》.pdf

1、Designation: E2908 12 (Reapproved 2018)Standard Guide forFire Prevention for Photovoltaic Panels, Modules, andSystems1This standard is issued under the fixed designation E2908; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the ye

2、ar of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide describes basic principles of photovoltaicmodule design, panel assembly, and system installation tore

3、duce the risk of fire originating from the photovoltaic sourcecircuit.1.2 This guide is not intended to cover all scenarios whichcould lead to fire. It is intended to provide an assembly ofgenerally-accepted practices.1.3 This guide is intended for systems which contain pho-tovoltaic modules and pan

4、els as dc source circuits, although therecommended practices may also apply to systems utilizing acmodules.1.4 This guide does not cover fire suppression in the eventof a fire involving a photovoltaic module or system.1.5 This guide does not cover fire emanating from othersources.1.6 This guide does

5、 not cover mechanical, structural,electrical, or other considerations key to photovoltaic moduleand system design and installation.1.7 This guide does not cover disposal of modules damagedby a fire, or other material hazards related to such modules.1.8 UnitsThe values stated in SI units are to be re

6、gardedas standard. No other units of measurement are included in thisstandard.1.9 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety, health, and environmental pra

7、ctices and deter-mine the applicability of regulatory limitations prior to use.1.10 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides

8、and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2E772 Terminology of Solar Energy ConversionE2481 Test Method for Hot Spot Protection Testing ofPhotovoltaic Modules2.2 Other Standards and Documents:IEC 6

9、1215 Crystalline silicon terrestrial photovoltaic (PV)modulesDesign qualification and type approvalIEC 61730 Photovoltaic (PV) module safety qualificationNorth American Board of Certified Energy Practitioners(NABCEP), Study Guide for Photovoltaic System Install-ersNFPA 70 US National Electrical Code

10、 (article 690)UL 1703 Standard for Flat-Plate Photovoltaic Modules andPanelsUL 1741 Inverters, Converters, and Controllers for Use inIndependent Power Systems3. Terminology3.1 Definitions of terms used in this standard may be foundin Terminology E772.3.2 Definitions:3.2.1 ground fault, na condition

11、where there is an unin-tended electrical connection between the active PV circuit andground.4. Summary of Practice4.1 Photovoltaic modules and panels should be designed tominimize the risk of fire and should be assembled with goodquality-control practices.4.2 Photovoltaic systems should be designed

12、to minimizethe risk of fire, and installed with fire safety in mind. Installersshould be aware of PV-related fires that have occurred and thecause of those fires.1This test method is under the jurisdiction of ASTM Committee E44 on Solar,Geothermal and Other Alternative Energy Sources and is the dire

13、ct responsibility ofSubcommittee E44.09 on Photovoltaic Electric Power Conversion.Current edition approved May 1, 2018. Published May 2018. Originallyapproved in 2012. Last previous edition approved in 2012 as E2908-12. DOI:10.1520/E2908-12R18.2For referenced ASTM standards, visit the ASTM website,

14、www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis

15、 international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TB

16、T) Committee.15. Significance and Use5.1 Photovoltaic modules are electrical dc sources. dcsources have unique considerations with regards to arc forma-tion and interruption, as once formed, the arc is not automati-cally interrupted by an alternating current. Solar modules areenergized whenever modu

17、les in the string are illuminated bysunlight, or during fault conditions.5.2 With the rapid increase in the number of photovoltaicsystem installations, this guide attempts to increase awarenessof methods to reduce the risk of fire from photovoltaic systems.5.3 This guide is intended for use by modul

18、e manufacturers,panel assemblers, system designers, installers, and specifiers.5.4 This guide may be used to specify minimum require-ments. It is not intended to capture all conditions or scenarioswhich could result in a fire.6. Arcing6.1 dc Arcing:6.1.1 An electrical arc can form where an electric

19、potentialexists between two neighboring conductors. Unlike ac arcswhich may be extinguished during the alternating-cycle ofcurrent, a dc arc will be maintained indefinitely until inter-rupted. A dc arc will be sustained until the voltage potential isreduced, an arc-detection device disrupts the flow

20、 of current, orthe effective distance between the conductors becomes toolarge to sustain the arc. Even once the arc is eliminated, the arcmay have been sufficient to cause burning or ignition ofsurrounding materials.6.1.2 An arc may propagate across the surface of the module(for example, along the g

21、ap between rows of cells) as materialsare burned away.6.1.3 The arc may extinguish and re-ignite under variableenvironmental conditions or with expansion and contraction ofaffected materials, and may also extinguish at night and restartthe next day.6.1.4 Common sources of arcs in PV modules:6.1.4.1

22、Cracks in solar cells (crystalline or thin film).6.1.4.2 Inadequate spacing between parts of different volt-age potentials.6.1.4.3 Improper bonding of interconnects to cells.6.1.4.4 Improper bonding of interconnects to bus bar.6.1.4.5 Improper bonding of bus bar to wiring terminal orconnector.6.1.4.

23、6 Insufficient allowance for thermal expansion andcontraction of materials, which leads to mechanical fatigue.Common examples include cell interconnects and expansionjoints in conduits.6.1.4.7 Insufficient strain relief between parts; especiallyfield wiring terminations, solder joints, and internal

24、conduc-tors.6.2 ac Arcing:6.2.1 Both ac and dc circuits may be present in a solarphotovoltaic system, and both circuits contain potential arcsources. A dc arc may be sustained over a larger distance andlonger duration than an ac arc due to the one-directional flowof the dc current, which is not easi

25、ly interrupted. The current inan ac arc always goes to zero twice per cycle.7. PV Modules and Panels7.1 Design Against ArcingModules shall be designed toreduce the risk of arcing.7.1.1 Modules shall meet the spacing requirements of IEC61730 or UL 1703 to reduce the occurrence of arcing underboth nor

26、mal operating conditions and fault conditions.7.1.2 Materials and processes used in the manufacture of PVmodules shall be designed to be durable and reliable over theentire service life of the PV module.7.1.3 Failure mechanisms, such as mismatch of thermalexpansion coefficients, metal fatigue, corro

27、sion or vibration,shall be considered during the selection of materials, modulelay-out, and assembly.7.1.4 Material selection shall include consideration of theoperating temperatures of the material and aging characteristicsof the material.7.2 Design for Arc and Fire Suppression:7.2.1 Materials in c

28、lose contact to potential arc sources,such as junction boxes, shall have a minimum arc andflammability rating in accordance with IEC 61730 or UL 1703.This helps to reduce the risk of fire in the event of an arcingevent.7.2.2 According to the 2011 National Electrical Code, anarc-detection device is r

29、equired to disconnect the current flowin the event of arcing. Depending on the location of the device,it may protect an individual module or an entire string.Consideration shall be given to the reliability of such devices,to avoid nuisance trips and costly servicing.7.3 Operating Temperature:7.3.1 A

30、 PV module converts a portion of the suns energyinto electrical energy. The portion of the suns energy that isnot converted into electrical energy is either reflected, trans-mitted through the module, or transformed into heat energy.Therefore, a PV module usually operates at a temperaturehotter than

31、 the surrounding ambient temperature.7.3.2 Operating Temperature ConsiderationsThe exactoperating temperature of a module, and of any given compo-nent within a module, depends on a variety of factors.7.3.2.1 Environmental FactorsWind speed, winddirection, ambient temperature, solar irradiance, and c

32、loudcover.7.3.2.2 Installation FactorsAngle of installation, racktype, module spacing, location, wind obstructions, trackingversus non-tracking, ventilation, shading events.7.3.2.3 Module FactorsCell mismatch (leading to non-uniform heat generation), insulated sections (e.g. junctionboxes), color, f

33、raming, transparency, material thermalconductivity, thermal convection characteristics, current-carrying limits of live parts.7.3.3 ShadingShading events can cause shaded cells to actas power sinks (resistors) as opposed to power generators.Therefore, shaded cells can run much hotter than neighborin

34、gcells. Although modules are designed to operate in un-shadedconditions, some degree of localized shading is inevitable inmost installations. Refer to Test Method E2481 for additionalinformation.E2908 12 (2018)27.3.3.1 The amount of heating of a cell depends on the shuntand series resistance charact

35、eristics of the shaded cells, thecurrent flowing through the cell, and whether the cells arepartially illuminated.7.3.3.2 Material CombustionMaterials in contact withcells shall be able to withstand temperatures under the shadedcondition without exceeding material ignition temperatureratings. The de

36、sign may be tested to assess material suitabilityper UL 1703, Section 19, Temperature Test.7.3.3.3 Modules shall have adequate protection in the eventof shading.7.3.3.4 DiodesA common method for providing shadingprotection is through bypass diodes connected in parallel withthe cells to be protected.

37、 As the forward and reverse charac-teristics of a PV cell are different, the diodes shall be sized toactivate in the event of shading of part or all of one or more ofthe cells to prevent the formation of localized hot spots. Thediodes must be able to safely handle the string current.Activation of th

38、e diode during a cell shading event shall notresult in overheating of the diode, nor materials surroundingthe diode. The diode shall be mounted and connected using arobust and reliable method, including strain relief as appropri-ate. Diode quality and the mounting method should be evalu-ated for dur

39、ability. If diodes are mounted mechanically, theyshould be tested under simulated field conditions to ensure thatadequate contact is maintained over time.7.4 Documentation:7.4.1 RecognitionThe module should be certified by anapproved organization to meet a minimum level of safety. Twostandards that

40、are commonly used to assess a minimum safetylevel are UL 1703 and IEC 61730.7.4.2 Quality SystemThe PV manufacturer shall have anestablished quality system to ensure all modules manufacturedmeet a basic level of quality from a fire safety standpoint.Sources of dc arcing shall be given specific atten

41、tion, as well asany material or process steps critical to module operatingtemperature.7.4.3 Installation GuideAny limitations on installationlocation or conditions critical to the safe operating state of a PVsystem shall be indicated in the Installation Guide. This mayinclude ambient conditions, mou

42、nting configuration, wiringrequirements, over-current protection devices and fuse ratings.8. PV Systems8.1 System Design Considerations:8.1.1 Series Fuse ProtectionIn most cases where two ormore strings of photovoltaic modules are connected in parallel,the branch or sub-string shall be protected by

43、a fuse. The fuseprotects the modules and other electrical components in thesystem from over-current in the event of a fault condition. Thetotal available current and fuse rating shall not exceed thatrecommended by the module or panel manufacturer.8.1.2 Module-to-Module ConnectionsAll wiring and con-

44、nectors used shall be of the type and sizing recommended bythe module manufacturer and in accordance with local codes.Wiring shall be suitable for the intended application, includingtemperature range, wire gauge, UV resistance, waterresistance, and system voltage. Consideration shall be given tothe

45、extreme and nominal conditions expected throughout themodule lifetime. The means for connection shall be in accor-dance with the module and connector Installation Guides orany applicable local codes. Wiring shall be mechanicallysecured, if required, to prevent strain on the electricalconnections, wi

46、th adequate slack to allow for thermal expan-sion and contraction of the wiring.8.1.3 Other WiringAll other wiring in the PV system shallbe suitable for the intended application and secured if required,with consideration given to the same factors as described formodule-to-module wiring. Wiring secur

47、ement means must beable to withstand outdoor conditions, including UV radiation,over the expected service life of the system, and should bechecked routinely as part of regular system maintenance. Ifwiring is in metallic conduit, particular attention should begiven to proper installation and wire man

48、agement techniques toreduce the possibility of ground faults.8.1.4 dc Disconnectsdc disconnects shall be used to allowsafe disconnection of a dc string from an inverter, combinerbox, charge controller or other electrical components in thesystem. The disconnect shall be rated appropriately for the dc

49、current and voltage of the system, in accordance with localcodes. Note that an ac-only disconnect may or may not besuitable for a dc circuit, as it relies on the alternating-nature ofac current to disrupt the current flow.8.1.5 InvertersInverters shall be appropriately sized forthe intended location, be approved to the local standard, suchas UL 1741, and meet local code requirements for connectionto the grid. Inverters may have built-in arc-detection capability,which disconnects the system in the event of an arc to reducedamage to the system and supporting structu