ASTM E3020-2016a Standard Practice for Ignition Sources《点火源的标准实施规程》.pdf

1、Designation: E3020 16aStandard Practice forIgnition Sources1This standard is issued under the fixed designation E3020; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the

2、 year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice describes a series of ignition sources thathave been used and that are potentially applicable to assessingfire-test-response characteristics resulting from

3、the ignition ofmaterials, products, or assemblies.1.2 This practice does not identify which of the ignitionsources described is applicable to any specific use since that isa function of the associated fire hazard (see also 5.2).1.3 This practice is not necessarily comprehensive and it ispossible tha

4、t other applicable ignition sources exist (see also5.3).1.4 This practice describes both flaming and non-flamingignition sources, since the outcome of a non-flaming ignitioncan be the eventual flaming ignition of these materials orproducts (see also 4.2).1.5 This practice does not provide pass/fail

5、criteria that canbe used as a regulatory tool.1.6 This fire standard cannot be used to provide quantitativemeasures.1.7 Fire testing is inherently hazardous. Adequate safe-guards for personnel and property shall be employed inconducting these tests.1.8 This standard is used to measure and describe t

6、heresponse of materials, products, or assemblies to heat and flameunder controlled conditions, but does not by itself incorporateall factors required for fire hazard or fire risk assessment of thematerials, products, or assemblies under actual fire conditions.1.9 This practice contains notes and foo

7、tnotes which pro-vide explanatory material. These notes and footnotes (exclud-ing those in tables and figures) shall not be consideredrequirements of the standard.1.10 The values stated in SI units are to be regarded asstandard in referee decisions. No other units of measurementare included in this

8、standard. See IEEE/ASTM SI 10 for furtherdetails.1.11 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of r

9、egulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D635 Test Method for Rate of Burning and/or Extent andTime of Burning of Plastics in a Horizontal PositionD1929 Test Method for Determining Ignition Temperatureof PlasticsD3675 Test Method for Surface Flammability of Flexi

10、bleCellular Materials Using a Radiant Heat Energy SourceD3874 Test Method for Ignition of Materials by Hot WireSourcesD5025 Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic MaterialsD5207 Practice for Confirmation of 20mm (50W) and125mm (500W) Test Flames for Small-S

11、cale BurningTests on Plastic MaterialsD5424 Test Method for Smoke Obscuration of InsulatingMaterials Contained in Electrical or Optical Fiber CablesWhen Burning in a Vertical Cable Tray ConfigurationD5537 Test Method for Heat Release, Flame Spread, SmokeObscuration, and Mass Loss Testing of Insulati

12、ng Mate-rials Contained in Electrical or Optical Fiber Cables WhenBurning in a Vertical Cable Tray ConfigurationD6194 Test Method for Glow-Wire Ignition of MaterialsE84 Test Method for Surface Burning Characteristics ofBuilding MaterialsE108 Test Methods for Fire Tests of Roof CoveringsE136 Test Met

13、hod for Behavior of Materials in a VerticalTube Furnace at 750CE162 Test Method for Surface Flammability of MaterialsUsing a Radiant Heat Energy SourceE176 Terminology of Fire StandardsE648 Test Method for Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source1This practi

14、ce is under the jurisdiction of ASTM Committee E05 on FireStandards and is the direct responsibility of Subcommittee E05.33 on Fire SafetyEngineering.Current edition approved Sept. 1, 2016. Published October 2016. Originallyapproved in 2015. Last previous edition approved in 2016 as E3020-16. DOI:10

15、.1520/E302016A.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor

16、Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1E662 Test Method for Specific Optical Density of SmokeGenerated by Solid MaterialsE906/E906M Test Method for Heat and Visible SmokeRelease Rates for Materials and Products Using a Ther-mopile MethodE1321 Test Method for Determining

17、Material Ignition andFlame Spread PropertiesE1352 Test Method for Cigarette Ignition Resistance ofMock-Up Upholstered Furniture AssembliesE1353 Test Methods for Cigarette Ignition Resistance ofComponents of Upholstered FurnitureE1354 Test Method for Heat and Visible Smoke ReleaseRates for Materials

18、and Products Using an Oxygen Con-sumption CalorimeterE1537 Test Method for Fire Testing of Upholstered Furni-tureE1590 Test Method for Fire Testing of MattressesE1623 Test Method for Determination of Fire and ThermalParameters of Materials, Products, and Systems Using anIntermediate Scale Calorimete

19、r (ICAL)E1822 Test Method for Fire Testing of Stacked ChairsE1995 Test Method for Measurement of Smoke ObscurationUsing a Conical Radiant Source in a Single ClosedChamber, With the Test Specimen Oriented HorizontallyE2058 Test Methods for Measurement of Material Flamma-bility Using a Fire Propagatio

20、n Apparatus (FPA)E2187 Test Method for Measuring the Ignition Strength ofCigarettesE2574/E2574M Test Method for Fire Testing of School BusSeat AssembliesIEEE/ASTM SI 10 American National Standard for Use ofthe International System of Units (SI): The Modern MetricSystem2.2 Institute of Electrical and

21、 Electronic Engineers (IEEE)Standards:3IEEE 383 IEEE Standard for Qualifying Class 1E ElectricCables and Field Splices for Nuclear Power GeneratingStationsIEEE 1202 IEEE Standard for Flame Testing of Cables forUse in Cable Tray in Industrial and Commercial Occu-pancies2.3 International Organization

22、for Standardization (ISO)Standards:4ISO 871 PlasticsDetermination of Ignition TemperatureUsing a Hot-Air FurnaceISO 5657 Reaction to Fire TestsIgnitability of BuildingProducts Using a Radiant Heat SourceISO 5659-2 PlasticsSmoke Generation Part 2: Determina-tion of Optical Density by a Single-Chamber

23、 TestISO 5660-1 Reaction to Fire TestsHeat Release, SmokeProduction and Mass Loss RatePart 1: Heat Release(Cone Calorimeter Method)ISO 8191-1 FurnitureAssessment of the Ignitability ofUpholstered FurniturePart 1: Ignition Source: Smoul-dering CigaretteISO 8191-2 FurnitureAssessment of the Ignitabili

24、ty ofUpholstered FurniturePart 2: Ignition Source: MatchFlame EquivalentISO 9705 Reaction to Fire TestsFull-Scale Room Test forSurface ProductsISO 12863 Standard Test Method for Assessing the IgnitionPropensity of CigarettesISO 12949 Standard Test Method for Measuring the HeatRelease Rate of Low Fla

25、mmability Mattresses and Mat-tress SetsISO 13943 Fire SafetyVocabulary2.4 International Electrotechnical Commission (IEC) Stan-dards:5IEC 60332-1-2 Tests on Electric and Optical Fibre CablesUnder Fire ConditionsPart 1-2: Test for Vertical FlamePropagation for a Single Insulated Wire or CableProcedur

26、e for 1 kW Pre-mixed FlameIEC 60332-2-1 Tests on Electric and Optical Fibre CablesUnder Fire ConditionsPart 2-1: Test for Vertical FlamePropagation for a Single Small Insulated Wire or Cable ApparatusIEC 60332-3-10 Tests on Electric and Optical Fibre CablesUnder Fire ConditionsPart 3-10: Test for Ve

27、rtical FlameSpread of Vertically-mounted Bunched Wires or CablesApparatusIEC 60695-2-10 Fire Hazard TestingPart 2-10: Glowing/Hot-Wire Based Test MethodsGlow-Wire Apparatusand Common Test ProcedureIEC 60695-2-11 Fire Hazard TestingPart 2-11: Glowing/Hot-Wire Based Test MethodsGlow-Wire FlammabilityT

28、est Method for End-ProductsIEC/TS 60695-2-20 Fire Hazard TestingPart 2-20:Glowing/Hot-Wire Based Test MethodsHot Wire Igni-tion TestApparatus, Confirmatory Test Arrangementand GuidanceIEC TS 60695-11-2 Fire Hazard TestingPart 11-2: TestFlames1 kW Nominal Pre-Mixed FlameApparatus,Confirmatory Test Ar

29、rangement and GuidanceIEC TS 60695-11-3 Fire Hazard TestingPart 11-3: TestFlames50 W FlameApparatus and ConfirmationalTest MethodsIEC TS 60695-11-4 Fire Hazard TestingPart 11-4: TestFlames50 W FlameApparatus and ConfirmationalTest Methods2.5 National Fire Protection Association (NFPA) Stan-dards:6NF

30、PA 260 Methods of Tests and Classification System forCigarette Ignition Resistance of Components of Uphol-stered FurnitureNFPA 261 Method of Test for Determining Resistance ofMock-Up Upholstered Furniture Material Assemblies toIgnition by Smoldering Cigarettes3Available from Institute of Electrical

31、and Electronics Engineers, Inc. (IEEE),445 Hoes Ln., Piscataway, NJ 08854-4141, http:/www.ieee.org.4Available from International Organization for Standardization (ISO), 1, ch. dela Voie-Creuse, CP 56, CH-1211 Geneva 20, Switzerland, http:/www.iso.org.5Available from International Electrotechnical Co

32、mmission (IEC), 3, rue deVaremb, P.O. Box 131, CH-1211 Geneva 20, Switzerland, http:/www.iec.ch.6Available from National Fire Protection Association (NFPA), 1 BatterymarchPark, Quincy, MA 02169-7471, http:/www.nfpa.org.E3020 16a2NFPA 262 Method of Test for Flame Travel and Smoke ofWires and Cables f

33、or Use in Air-Handling SpacesNFPA 265 Methods of Fire Tests for Evaluating Room FireGrowth Contribution of Textile or Expanded Vinyl WallCoverings on Full Height Panels and WallsNFPA 270 Test Method for Measurement of Smoke Obscu-ration Using a Conical Radiant Source in a Single ClosedChamberNFPA 28

34、6 Methods of Fire Tests for Evaluating Contribu-tion of Wall and Ceiling Interior Finish to Room FireGrowthNFPA 287 Test Methods for Measurement of Flammabilityof Materials in Cleanrooms Using a Fire PropagationApparatus (FPA)NFPA 289 Method of Fire Test for Individual Fuel PackagesNFPA 701 Methods

35、of Fire Tests for Flame Propagation ofTextiles and Films2.6 Underwriters Laboratories (UL) Standards:7UL 94 Tests for Flammability of Plastic Materials for Partsin Devices and AppliancesUL 1040 Fire Test of Insulated Wall ConstructionUL 1666 Test for Flame Propagation Height of Electricaland Optical

36、-Fiber Cables Installed Vertically in ShaftsUL1685 Vertical-Tray Fire-Propagation and Smoke-ReleaseTest for Electrical and Optical-Fiber CablesUL 1715 Standard for Fire Test of Interior Finish Material2.7 Federal Aviation Administration Standard:8Aircraft Material Fire Test Handbook DOT/FAA/AR-00/12

37、,FAA Technical Center, April 20002.8 FM Global Standard:9FM 4880 Approval Standard for Class 1 Fire Rating ofInsulated Wall or Wall and Roof/Ceiling PanelsInteriorFinish Materials or Coatings and Exterior Wall Systems2.9 U.S. Department of Commerce Standard:1016 CFR 1633 Standard for the Flammabilit

38、y (Open-Flame)of Mattresses and Mattress and Foundation Sets2.10 British Standards Institution Standard:11BS 5852 Methods of test for assessment of the ignitability ofupholstered seating by smouldering and flaming ignitionsources2.11 California Technical Bulletins:CALTB 121 Flammability Test Procedu

39、re for Mattresses forUse in High Risk Occupancies (1980)CAL TB 133 Flammability Test Procedure for Seating Fur-niture for Use in Public Occupancies (1991)3. Terminology3.1 Use Terminology E176 or ISO 13943 for definitions ofterms used in this test method and associated with fire issues.Where differe

40、nces exist in definitions, those contained inTerminology E176 shall be used.3.2 Definitions:3.2.1 ignition, nthe initiation of combustion.3.2.1.1 DiscussionThe combustion may be evidenced byglow, flame, detonation, or explosion. The combustion may besustained or transient. E1763.2.2 piloted ignition

41、, nignition of combustible gases orvapors by a pilot source of ignition (compare spontaneousignition, unpiloted ignition). E1763.2.3 pilot source of ignition, na discrete source of energy,such as, for example, a flame, spark, electrical arc, or glowingwire (compare piloted ignition, unpiloted igniti

42、on). E1763.2.4 smoldering, ncombustion of a solid without flame,often evidenced by visible smoke.3.2.4.1 DiscussionSmoldering can be initiated by smallsources of ignition, especially in dusts or fibrous or porousmaterials, and may persist for an extended period of time afterwhich a flame may be prod

43、uced. E1763.2.5 spontaneous ignition, nunpiloted ignition caused byan internal exothermic reaction (compare piloted ignition).E1763.2.6 sustained flaming, nflame on or over the surface ofa test specimen that lasts longer than a defined period of time(contrast transitory flaming).3.2.6.1 DiscussionTy

44、pically, the same defined period isused to define “transitory flaming.” See the specific standardtest method for applicable defined period of time. E1763.2.7 transitory flaming, nflame on or over the surface ofa test specimen that does not last longer than a defined periodof time (contrast sustained

45、 flaming).3.2.7.1 DiscussionTypically, the same defined period oftime is used to define “sustained flaming.” See the specificstandard test method for applicable defined period of time.E1763.2.8 unpiloted ignition, nignition caused by one or moresources of energy without the presence of a pilot sourc

46、e ofignition (compare piloted ignition, spontaneous ignition). E1764. Summary of Practice4.1 This practice describes a series of standard ignitionsources used in test methods, specifications, or regulations toassess fire-test-response characteristics of materials, products,or assemblies.4.2 These ig

47、nition sources include those that assess theresponse to non-flaming ignition sources, including smolderingcigarettes, glow wires, hot wires, and radiant heat sources.4.3 These ignition sources include those that assess theresponse to flaming ignition sources, including both premixedflames and diffus

48、ion flames.4.4 This practice does not offer pass/fail criteria.4.5 The information included in this practice is representa-tive of the ignition sources in the various standards at the timethis practice was written. Users of this practice are encouraged7Available from Underwriters Laboratories (UL),

49、2600 N.W. Lake Rd., Camas,WA 98607-8542, http:/.8Available from Federal Aviation Administration (FAA), 800 IndependenceAve., SW, Washington, DC 20591, http:/www.faa.gov.9Available from FM Global, Norwood, MA, .10Available from U.S. Consumer Product Safety Commission, Washington, DC,20207.11Available from British Standards Institution (BSI), 389 Chiswick High Rd.,London W4 4AL, U.K., http:/.E3020 16a3to consult the latest edition of any standard at the time ofproposed use of an ignit