ASTM F144-1980(2015) Standard Practice for Making Reference Glass-Metal Sandwich Seal and Testing for Expansion Characteristics by Polarimetric Methods《制造标准玻璃与金属夹层封接以及采用偏振法测定膨胀特性的标.pdf

1、Designation: F144 80 (Reapproved 2015)Standard Practice forMaking Reference Glass-Metal Sandwich Seal and Testingfor Expansion Characteristics by Polarimetric Methods1This standard is issued under the fixed designation F144; the number immediately following the designation indicates the year of orig

2、inaladoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers the preparation and testing of areference g

3、lass-metal sandwich seal for determining stress inthe glass or for determining the degree of thermal expansion(or contraction) mismatch between the glass and metal. Testsare in accordance with Test Method F218 (Section 2).1.2 This practice applies to all glass and metal (or alloy)combinations normal

4、ly sealed together in the production ofelectronic components.1.3 The practical limit of the test in deriving mismatch isapproximately 300 ppm, above which the glass is likely tofracture.1.4 This standard does not purport to address all of thesafety problems, if any, associated with its use. It is th

5、eresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2F15 Specification for Iron-Nickel-Cobalt Sealing AlloyF30 Specification for Iron-Nicke

6、l Sealing AlloysF31 Specification for Nickel-Chromium-Iron Sealing AlloysF47 Test Method for Crystallographic Perfection of Siliconby Preferential Etch Techniques (Withdrawn 1998)3F79 Specification for Type 101 Sealing GlassF105 Specification for Type 58 Borosilicate Sealing GlassF218 Test Method fo

7、r Measuring Optical Retardation andAnalyzing Stress in GlassF256 Specification for Chromium-Iron Sealing Alloys with18 or 28 Percent Chromium3. Summary of Practice3.1 Seals of a standard configuration are prepared fromrepresentative specimens of the glass and metal to be tested.The glass and metal a

8、re cleaned, treated, and sized to specifiedproportions. Plane-interfaced seals are formed, annealed, andmeasured for residual optical retardation. The stress parallel tothe interface in each seal is calculated from the opticalretardation, and the average stress and thermal expansionmismatch are comp

9、uted for the sample.4. Significance and Use4.1 The term “reference” as employed in this practiceimplies that either the glass or the metal of the referenceglass-metal seal will be a “standard reference material” such asthose supplied for other physical tests by the National Instituteof Standards and

10、 Technology, or a secondary reference materialwhose sealing characteristics have been determined by seals toa standard reference material (see NBS Special Publication260). Until standard reference materials for seals are estab-lished by the NIST, secondary reference materials may beagreed upon betwe

11、en manufacturer and purchaser.5. Apparatus5.1 Polarimeter, as specified in Test Method F218 formeasuring optical retardation and analyzing stress in glass.5.2 Cut-Off Saw, with diamond-impregnated wheel and No.180 grit abrasive blade under flowing coolant for cutting andfine-grinding glass rod.5.3 G

12、lass Polisher, buffing wheel with cerium oxide polish-ing powder or laboratory-type equipment with fine-grindingand polishing laps.5.4 Heat-Treating and Oxidizing Furnaces, with suitablecontrols and with provisions for appropriate atmospheres(Annex A1) for preconditioning metal, if required.5.5 Seal

13、ing Furnace, radiant tube, muffle or r-f inductionwith suitable controls and provision for use with inert atmo-sphere.5.6 Annealing Furnace, with capability of controlled cool-ing.1This practice is under the jurisdiction of ASTM Committee C14 on Glass andGlass Products and is the direct responsibili

14、ty of Subcommittee C14.04 on Physicaland Mechanical Properties.Current edition approved May 1, 2015. Published May 2015. Originallyapproved in 1971. Last previous edition approved in 2010 as F144 80 (2010).DOI: 10.1520/F0144-80R15.2For referenced ASTM standards, visit the ASTM website, www.astm.org,

15、 orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International, 100 Barr Harbor

16、Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15.7 Ultrasonic Cleaner, optional.5.8 Fixture for Furnace Sealing, design as suggested inAnnex A2.5.9 Micrometer Caliper, with index permitting direct read-ing of 0.02 cm.5.10 Immersion Mercury Thermometer.6. Materials6.1 MetalFive r

17、epresentative specimen pairs of the metalfrom either rod or plate stock with dimensions satisfying therequirements of 7.1. The surfaces to be sealed should berelatively free of scratches, machine marks, pits, or inclusionsthat would induce localized stresses. The sealing surfacesshould terminate in

18、sharp edges at the peripheral corners to actas a glass stop. Edges that are rounded, such as appear ontumbled parts, will have the tendency to permit glass overflow.The opposite faces of each plate should be parallel within 0.5.6.2 GlassFive representative specimens of rod or plateglass, cut with ei

19、ther diamond-impregnated or other abrasivecutting wheels under flowing water. Dimensions (volume)must satisfy the requirements of 7.2, and the faces should beflat and parallel within 0.5 for uniform flow during sealing.7. Test Specimens7.1 The metal specimens may take the form of circular,square, or

20、 rectangular plates. In each case the dimension d, Fig.1, designates the path along which the optical retardation in thefinished seal is measured. Two identical metal plates of any ofthe indicated shapes are required for a seal. The thickness, tm,of each plate should be at least 0.7 mm and d/tmshoul

21、d be atleast 6.7.2 Glass with suitable optical transmission of any shapemay be used, provided it flows essentially bubble-free to fill theentire volume between the metal plates as in Fig. 2. Experienceindicates, however, that best results are obtained with flat glassconforming closely to the outline

22、 of the metal plates. Thethickness of the glass before sealing shall be such that it equalstmafter sealing within 15 %. Thus, the volume of glassnecessary to fill the void between the metal plates to athickness equal to that of a single plate becomes the determin-ing dimensional criterion for the gl

23、ass.7.3 When used as an acceptance test by producer and user,the number of test seals representing one determination shall beestablished by mutual agreement. However two seals are aminimum requirement for one determination.8. Preparation of Specimens8.1 MetalChemically clean the specimens to remove

24、sur-face contaminants, especially lubricants and fingerprints fromfabrication and handling. Usually it is advisable to preoxidizeparts as described in AnnexA1. Preoxidation promotes a betterglass-to-metal bond and relieves cold working stresses.8.2 GlassUsing optical glass techniques grind and polis

25、hthe sealing surfaces of the glass specimens with either wetabrasive wheels or water slurries of abrasive on a lap. Thepolished surfaces should satisfy the dimensional criteria of 6.2and 7.2, and be without chips, nicks, or scratches. Remove anysurface contaminants which could produce bubbly seals.

26、Anultrasonic wash may be used. See Annex A1.9. Procedure for Making the Sandwich Seal9.1 Record dimensions of metal plates and glass parts.9.2 Make the seal in a furnace or by induction heating of themetal utilizing suitable specimen holders or supports undercontrolled conditions of temperature and

27、time. See Annex A2.10. Annealing10.1 Once a symmetrical, bubble-free seal has been made,proper annealing of the seal becomes the most critical part ofthe procedure. It is by this operation that all stresses arerelieved except those due to the difference in thermal contrac-tion of the two materials f

28、rom annealing temperature levels.This process involves heating the seal to a temperaturesomewhat higher than the annealing point of the glass andmaintaining this temperature for a time sufficient to relieve theexisting strain. The test specimen is then cooled slowly at aconstant rate. As an alternat

29、ive, annealing can proceed directlyon cooling during the making of a seal.10.2 Seal stress and associated expansion mismatch can bevaried markedly by annealing schedule modification. For thisreason, when the test is used as an acceptance specification, itis strongly recommended that producer and use

30、r mutuallydefine the annealing schedule and establish rigid controls for itsmaintenance.11. Procedure for Measuring Optical Retardation11.1 For each specimen measure the retardation in theannealed seal due to the stress parallel to the interfaceaccording to Test Method F218.11.1.1 Position the plane

31、 of the seal (in an immersion liquid,if needed) in a direction 45 from the direction of vibration ofthe polarizer and analyzer, so that the line of sight, or lightpath, is through the maximum glass dimension in the directiond shown in Fig. 1. In a circular seal, for example, this would bethe diamete

32、r.11.1.2 Determine the retardation along the light paththrough the glass in terms of degrees of rotation of analyzer.Rotate in a direction that causes the curved black fringes seenFIG. 1 Permissible Metal Shapes.FIG. 2 General Seal Configuration.F144 80 (2015)2within the glass to appear to merge in

33、the center of crosssection of the glass and away from the glassmetal interfaces.Rotate the analyzer so that any light or “gray” area which mayexist between the fringes disappears and a dark spot, or area, isformed. This condition is termed the point of extinction.NOTE 1Sealing combinations may exist

34、 in which the thermal expan-sion coefficients of glass and metal at room temperature may differsignificantly. In these cases it may be important to record the temperatureof the refraction liquid (or the seal) at the time the retardation is measured.NOTE 2In certain glasses, especially those composit

35、ions containingmore than one alkali oxide, part of the retardation observed may not beassociated with the mismatch stress of interest. In these cases somestructural birefringence is caused by temporary stresses at elevatedtemperatures. Evaluate the exact analysis of mismatch stress by com-pletely re

36、moving the metal member by acid immersion. Read again theretardation at the same glass surface. Then algebraically subtract anyresidual retardation from that previously observed.11.1.3 If an immersion liquid is used record the nominalindex of refraction, nD, of the liquid, and measure and recordthe

37、temperature of the immersion liquid to the nearest 1Cusing an immersion mercury thermometer.11.1.4 Record the type of light source and the effectivewavelength, L, in nanometers, of the light for which theretardation has been measured. Record the interface positionand the major stress component posit

38、ion and sense (tension orcompression) as defined in Test Method F218.11.1.5 Measure the length d along the light path (Fig. 1)using a micrometer caliper.12. Calculations12.1 Calculate the retardation per unit length of each speci-men as follows:R 5 L 3A!/180 3d! (1)where:R = retardation per unit len

39、gth, nm/cm,L = wavelength of light source, nm,A = rotation of analyzer, deg, andd = length of the light path through the interface, cm.NOTE 3In determining the light path only that length of glass sealedat the interface is considered. In a complete seal, this may be the same asd of Fig. 1, but it ma

40、y be less. See A2.6 of Annex A2.12.2 Calculate the average, R, of the values of R for thespecimens in a test lot.12.3 For each test lot, calculate the average seal stressparallel to the interface using the relationship:S 5 R/K (2)where:S = stress parallel to interface, Pa,R= average retardation per

41、unit length of the test specimens,nm/cm, andK = stress-optical coefficient of the glass, nm/cmPa.NOTE 4The stress-optical coefficient K of any reference glass shall besupplied by the producer. Values for typical sealing glasses are found inTable A1 of Specifications F79 and F105.12.4 Calculate the t

42、hermal expansion mismatch (the differ-ential thermal contraction between the glass and the metal fromthe setting point (approximately the strain point) of the glass toroom temperature) as follows: 5S 1 2 kv!2FtgEmtm12EgG106(3)where: = expansion mismatch, ppm,tmand tg= thickness of metal and glass, r

43、espectively, cm,Emand Eg= Youngs modulus of metal and glass,respectively, Pa,k = shape factor (see Fig. 3)4and,v = composite Poissons ratio, given by:v 5Stg2tmDvg1SEmEgDS11vg11vmDvmFtg2tm1S11vg11vmDEmEgG(4)where vgand vmare glass and metal Poissons ratios,respectively.13. Report13.1 The report shall

44、 include the following:13.1.1 Type of metal and identification,13.1.2 Type of glass and identification,13.1.3 Dimensions of metal plate and glass for eachspecimen,13.1.4 Number of specimens tested,13.1.5 Annealing schedule,13.1.6 Length of the light path through glass at the center ofcross section n

45、ear the interface for each specimen,13.1.7 Stress-optical coefficient of the glass,13.1.8 Type of light source and effective wavelength,13.1.9 Nominal index of refraction of immersion liquid andits temperature at the time of retardation measurements or, if noimmersion liquid is used, the temperature

46、 of the seal, and13.1.10 Average value, range, and sense of thermal expan-sion mismatch.414. Keywords14.1 expansion mismatch; glass-metal seals4Gulati, S. T., and Hagy, H. E., “Theory of the Narrow Sandwich Seal” and“Finite Element Analysis and Experimental Verification of the Shape Factor forNarrow

47、 Sandwich Seals,” Journal of the American Ceramic Society, Vol 61, 1978,pp. 260263, 263267.F144 80 (2015)3ANNEXESA1. DIRECTIONS FOR CLEANING AND HEAT-TREATING SPECIMENS OF GLASS AND METAL FOR MAKING SEALSA1.1 Clean the glass with ultrasonic agitation in 0.5 60.01 % nonionic wetting agent solution at

48、 50 6 5C for 5 61 min. If necessary, precede this by an immersion in a 15 %aqueous hydrofluoric acid5solution for 0.15 to 1 min; this isrecommended particularly for aged or weathered glass. Rinsesuccessively in distilled or deionized water and alcohol. Blowdry with nitrogen or filtered air, and then

49、 oven dry at 110 65C for 15 6 2 min. Rinse water (distilled or deionized) shallhave a resistivity greater than 2 M cm.A1.2 Commonly used ASTM sealing alloys are Fe-Ni-Co,Fe-Ni, Ni-Cr-Fe, and Cr-Fe (A1.1). Degrease these alloys intrichloroethylene vapor or liquid, and follow this with theultrasonic cleaning procedure in A1.1. Rinse in water. Immersein 10 6 1 % hydrochloric acid solution at 1006 5C for 2 60.5 min and follow this with the final rinsing and dryingprocedure in A1.1.NOTE A1.1These sealing alloys are covered by the following ASTMspecific