ASTM F31-2005 Standard Specification for 42% Nickel-6% Chromium-Iron Sealing Alloy《42%镍6%铬铁焊接用合金的标准规范》.pdf

1、Designation: F 31 05Standard Specification for42 % Nickel-6 % Chromium-Iron Sealing Alloy1This standard is issued under the fixed designation F 31; the number immediately following the designation indicates the year of originaladoption or, in the case of revision, the year of last revision.Anumber i

2、n parentheses indicates the year of last reapproval.Asuperscriptepsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers an iron-nickel-chromium alloy(UNS K94760) used primarily for glass-sealing applications inelectronic devices.1.2 The v

3、alues stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.1.3 The following safety hazards caveat applies only toSection 13. This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is t

4、heresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2E18 Test Methods for Rockwell Hardness and RockwellSuperficial Hardness of Metallic M

5、aterialsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE38 Methods for Chemical Analysis of Nickel-Chromiumand Nickel-Chromium-Iron Alloys3E112 Test Methods for Determining the Average GrainSizeE 228 Test Method for Linear Thermal Expansion of Solid

6、Materials with a Vitreous Silica DilatometerF14 Practice for Making and Testing Reference Glass-Metal Bead-SealF 140 Practice for Making Reference Glass-Metal ButtSeals and Testing for Expansion Characteristics by Polari-metric MethodsF 144 Practice for Making Reference Glass-Metal Sand-wich Seal an

7、d Testing for Expansion Characteristics byPolarimetric Methods3. Ordering Information3.1 Orders for material under this specification shall includethe following information:3.1.1 Size,3.1.2 Temper (Section 6),3.1.3 Surface finish (Section 8),3.1.4 Marking and packaging (Section 13), and3.1.5 Certifi

8、cation if required.4. Chemical Composition4.1 The material shall conform to the requirements of Table1 as to chemical composition.NOTE 1The major constituents of this alloy may be adjusted by themanufacturer so that the alloy meets the requirement for thermal expan-sion.5. Chemical Analysis5.1 Chemi

9、cal analysis shall be made, when desired, inaccordance with Methods E38.6. Surface Lubricants6.1 All lubricants used during cold-working operations suchas drawing, rolling, or spinning, shall be capable of beingremoved readily by any of the common organic degreasingsolvents.7. Temper7.1 The desired

10、temper of the material shall be specified onthe purchase order. Unless otherwise specified, wire, rod, andtubing shall be given a final bright anneal by the manufacturer.Strip and sheet shall be annealed properly to develop drawing1This specification is under the jurisdiction of ASTM Committee F01 o

11、nElectronics and is the direct responsibility of Subcommittee F01.03 on MetallicMaterials.Current edition approved Jan. 1, 2005. Published January 2005. Originallyapproved in 1963 as F 31 63 T. Last previous edition approved in 1999 asF 31 94 (1999)e1.2For referenced ASTM standards, visit the ASTM w

12、ebsite, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Discontinued; see 1988 Annual Book of ASTM Standards, Vol 03.05.TABLE 1 Chemical CompositionElement Composit

13、ion, %Nickel, nominal 42.0Chromium, nominal 5.6Carbon, max 0.07Manganese, max 0.25Phosphorus, max 0.025Sulfur, max 0.025Silicon, max 0.30Aluminum, max 0.20Iron remainder1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.properties. For

14、deep drawing, the hardness shall not exceedRockwell B90 when determined in accordance with TestMethods E18.8. Grain Size8.1 Strip and sheet for deep drawing applications shall havean average grain size not larger than ASTM No. 5 (Note 2),with no more than 10 % of the grains larger than No. 5 whenmea

15、sured in accordance with Test Methods E112. For mate-rials less than 0.005 in. (0.13 mm) in thickness, the grain sizeshall be such that there are no less than 4 grains across thethickness.NOTE 2This corresponds to a grain size finer than 0.065 mm or 16grains/in.2of image at 1003.9. Dimensional Toler

16、ances9.1 Cold-Rolled StripCold-rolled strip shall conform tothe permissible variations in dimensions prescribed in Table 2,Table 3, and Table 4.9.2 Round Wire and RodWire and rod shall conform tothe permissible variations in dimension prescribed in Table 5.TABLE 2 Permissible Variations in Thickness

17、 of Cold-Rolled StripNOTE 1 Measurement shall be made at least38 in. (9.5 mm) from the edge of strip over 1-in. (25.4 mm) wide.Specified Thickness Permissible Variations in Thickness for Width Given, 6in. (mm) Under 3 in.(Under 76mm)Over 3 to 6in.(76to150mm)Over 6 to 12in.(150 to 300mm)Over 12 to 16

18、in.(300 to 400mm)0.160 to 0.100, incl (4.06 to 2.54) 0.002 (0.05) 0.003 (0.076) 0.004 (0.10) 0.004 (0.10)0.099 to 0.069, incl (2.51 to 1.75) 0.002 (0.05) 0.003 (0.076) 0.003 (0.076) 0.004 (0.10)0.068 to 0.050, incl (1.73 to 1.27) 0.002 (0.05) 0.003 (0.076) 0.003 (0.076) 0.003 (0.076)0.049 to 0.035,

19、incl (1.24 to 0.89) 0.002 (0.05) 0.0025 (0.064) 0.003 (0.076) 0.003 (0.076)0.034 to 0.029, incl (0.86 to 0.74) 0.0015 (0.038) 0.002 (0.05) 0.0025 (0.064) 0.0025 (0.064)0.028 to 0.026, incl (0.71 to 0.66) 0.0015 (0.038) 0.0015 (0.038) 0.002 (0.05) 0.002 (0.05)0.025 to 0.020, incl (0.64 to 0.51) 0.001

20、 (0.025) 0.0015 (0.038) 0.002 (0.05) 0.002 (0.05)0.019 to 0.017, incl (0.48 to 0.43) 0.001 (0.025) 0.001 (0.025) 0.0015 (0.038) 0.002 (0.05)0.016 to 0.012, incl (0.41 to 0.30) 0.001 (0.025) 0.001 (0.025) 0.0015 (0.038) 0.0015 (0.038)0.011 to 0.0101, incl (0.28 to 0.256) 0.001 (0.025) 0.001 (0.025) 0

21、.001 (0.025) 0.0015 (0.038)0.010 to 0.0091, incl (0.254 to 0.231) 0.001 (0.025) 0.001 (0.025) 0.001 (0.025) 0.001 (0.025)0.009 to 0.006, incl (0.228 to 0.152) 0.00075 (0.019) 0.00075 (0.019) . .Under 0.006 (0.152) 0.0005 (0.013) 0.0005 (0.013) . .TABLE 3 Permissible Variation in Thickness Across Wid

22、th of StripSpecified ThicknessMaximum Variation in Thickness Across Width of Strip, Within Those Provided for in Table 1 for Edge Measurementsfor Widths and Thicknesses Given,in. (mm)5 in. andUnder(127 mm andUnder)Over 5 to12 in.(Over 127 to 300mm)Over 12 to 24 in.,incl(Over 300 to 600mm)0.005 to 0.

23、010, incl (0.13 to 0.25) 0.00075 (0.019) 0.001 (0.025) 0.0015 (0.038)Over 0.010 to 0.025, incl (0.25 to 0.64) 0.001 (0.025) 0.0015 (0.038) 0.002 (0.051)Over 0.025 to 0.065, incl (0.64 to 1.65) 0.0015 (0.038) 0.002 (0.051) 0.0025 (0.064)Over 0.065 to 3/16 , excl (1.65 to 4.74) 0.002 (0.051) 0.0025 (0

24、.064) 0.003 (0.076)TABLE 4 Permissible Variations in Width of Cold-Rolled Strip Supplied in CoilsSpecified Thickness Permissible Variations in Width for Widths Given, 6in. (mm)Under12to316 in.(Under12.7 to4.75 mm)12 to6in.(12.7 to150 mm)Over 6 to9in.(150 to225 mm)Over 9 to12 in.(225 to300 mm)Over 12

25、to 20 in.(300 to500 mm)Over20 to231516 in.(500 to 600mm)0.187 to 0.161 (4.75 to 4.09) . 0.016 (0.41) 0.020 (0.51) 0.020 (0.51) 0.031 (0.79) 0.031 (0.79)0.160 to 0.100 (4.06 to 2.54) 0.010 (0.25) 0.010 (0.25) 0.016 (0.41) 0.016 (0.41) 0.020 (0.51) 0.020 (0.51)0.099 to 0.069 (2.51 to 1.75) 0.008 (0.20

26、) 0.008 (0.20) 0.010 (0.25) 0.010 (0.25) 0.016 (0.41) 0.020 (0.51)0.068 and under (1.73) 0.005 (0.13) 0.005 (0.13) 0.005 (0.13) 0.010 (0.25) 0.016 (0.41) 0.020 (0.51)TABLE 5 Permissible Variations in Diameter of Wire and RodSpecified DiameterPermissible Variations inDiameter, 6in. (mm) in. (mm)Wire

27、(Coiled, Spooled or Straight Lengths)0.002 to 0.0043 (0.051 to 0.109) 0.0002 (0.005)0.0044 to 0.0079 (112 to 0.200) 0.00025 (0.0064)0.008 to 0.0149 (0.203 to 0.378) 0.0003 (0.0076)0.015 to 0.0199 (0.381 to 0.505) 0.0004 (0.0102)0.020 to 0.0309 (0.508 to 0.785) 0.0005 (0.0127)0.031 to 0.0409 (0.787 t

28、o 1.039) 0.0006 (0.0152)0.041 to 0.0609 (1.041 to 1.547) 0.0007 (0.0178)0.061 to 0.0809 (1.549 to 2.055) 0.0008 (0.0203)0.081 to 0.1259 (2.057 to 3.198) 0.001 (0.0254)0.126 to 0.1569 (3.200 to 3.985) 0.0015 (0.038)0.157 to 0.250 (3.988 to 6.35) 0.002 (0.051)Rod, Centerless Ground Finish (Straight Le

29、ngths)0.030 to 0.0549 (0.766 to 1.394) 0.0005 (0.0127)0.055 to 0.1249 (1.397 to 3.172) 0.001 (0.0254)0.125 to 0.499 (3.175 to 12.67) 0.0015 (0.038)0.500 to 0.999 (12.70 to 25.37) 0.002 (0.051)1.000 to 1.625 (25.4 to 41.27) 0.0025 (0.064)1.626 to 1.749 (41.3 to 44.42) 0.003 (0.076)1.750 to 1.999 (44.

30、45 to 50.17) 0.004 (0.010)2.000 to 4.000 (50.8 to 101.6) 0.005 (0.013)F310529.3 Cold-Drawn TubingCold-drawn tubing, available ei-ther as seamless or welded, shall conform to the permissiblevariations prescribed in Table 6.10. Surface Finish10.1 The standard surface finishes available shall be thoser

31、esulting from the following operations:10.1.1 Hot rolling,10.1.2 Forging,10.1.3 Centerless grinding (rod),10.1.4 Belt polishing,10.1.5 Cold rolling, and drawing, and10.1.6 Wire drawing.10.2 Care shall be taken to prevent the depletion of surfacechromium during processing.11. Thermal Expansion Charac

32、teristics11.1 The average linear coefficient of thermal expansionshall be within limits specified in Table 7.12. Test Method for Thermal Expansion12.1 Heat the specimen for 15 min at 1100C in a hydrogenor cracked-ammonia atmosphere with a dew point of 40Cand cool to room temperature at a rate not ex

33、ceeding 5C/min.12.2 Determine the thermal expansion characteristics inaccordance with Test Method E 228.12.3 The thermal expansion match between the alloy and aglass may be evaluated by preparing and testing an assembly inaccordance with Practice F14, Practice F 140, or PracticeF 144.13. Test Result

34、s13.1 Observed or calculated values obtained from analysis,measurements, or tests shall be rounded off in accordance withthe rounding-off method of Practice E29, to the nearest unit inthe last right-hand place of figures used in expressing thespecified limit.14. General Requirements14.1 The material

35、 shall be commercially smooth, uniform incross section, in composition, and in temper; it shall be free ofscale, corrosion, cracks, seams, scratches, slivers, and otherdefects as best commercial practice will permit.15. Packaging and Package Marking15.1 Packaging shall be subject to agreement betwee

36、n thepurchaser and seller.15.2 The material as furnished under this specification shallbe identified by the name or symbol of the manufacturer and bymelt number. The lot size for determining compliance with therequirements of this specification shall be one heat.16. Investigation of Claims16.1 Where

37、 any material fails to meet the requirements ofthis specification, the material so designated shall be handled inaccordance with the agreement mutually agreed upon betweenthe purchaser and the seller.17. Keywords17.1 glass-to-metal sealing; iron-nickel-chromium alloy;UNS K94760TABLE 6 Permissible Va

38、riations in Dimensions of Standard TubingSpecified Outside Diameter, Permissible VariationsAin. (mm)Outside Diameter Inside DiameterWall Thickness, plus orminus, %in. (mm) in. (mm)Under 0.093 (2.36) + 0.0020.000( + 0.051)(0.000)+ 0.0000.002( + 0.000)(0.051)100.093 to 0.187, excl (2.36 to 4.75) + 0.0

39、03 ( + 0.076) + 0.000 ( + 0.000) 100.000 (0.000) 0.003 (0.076)0.187 to 0.550, excl (4.75 to 12.7) + 0.004 ( + 0.102) + 0.000 ( + 0.000) 100.000 (0.000) 0.004 (0.102)0.500 to 1.500, excl (12.7 to 38.1) + 0.005 ( + 0.13) + 0.000 ( + 0.000) 100.000 (0.00) 0.005 (0.13)AAny two of the three dimensional t

40、olerances listed may be specified.TABLE 7 Coefficient of Thermal ExpansionATemperature Range, C Coefficient, 106/C30 to 42530 to 3509.7 to 10.78.5 to 9.5ATypical expansion data up to 700C are given in the Appendix.F31053APPENDIX(Nonmandatory Information)X1. THERMAL EXPANSION DATAX1.1 The following t

41、ypical thermal expansion data for42 % nickel-6 % chromium-iron sealing alloy (UNS K94760)are given for information only.Temperature Range. CAverage Linear Coefficient of ThermalExpansion. m/mC30 to 300 7.930 to 400 9.830 to 500 11.230 to 600 12.130 to 700 13.0ASTM International takes no position res

42、pecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This

43、standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM Intern

44、ational Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown be

45、low.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F31054