ASTM E433-1971(2013) 9375 Standard Reference Photographs for Liquid Penetrant Inspection《液体渗透检查用标准参考照片》.pdf

1、Designation: E433 71 (Reapproved 2013)Standard Reference Photographs forLiquid Penetrant Inspection1This standard is issued under the fixed designation E433; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision

2、. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 These reference photographs are supplied as a means ofestablishing types and characteristics of surface discontinuitiesdetectable b

3、y the penetrant examination methods. They may beused as a reference for acceptance standards, specifications anddrawings.1.2 Actual dimensions including maximum length of indi-cations and number of indications per unit area must bespecified by the users of this document. No attempt has beenmade to e

4、stablish limits of acceptability or the metallurgicalcause of a discontinuity.NOTE 1Examples of these reference photographs are shown in Figs.1-8.2. Referenced Documents2.1 ASTM Standards:2E165 Practice for Liquid Penetrant Examination for GeneralIndustry2.2 ASTM Adjuncts:Reference Photographs for P

5、enetrant Inspection33. Classifications3.1 TypesFor the purposes of this standard there are twotypes of indications, which are defined as follows:3.1.1 Type I IndicationsThose in which neither of themeasurable dimensions is greater than three times the other.3.1.2 Type II IndicationsThose in which on

6、e of the mea-surable dimensions is at least three times greater than the other.3.2 ClassesFor purposes of this standard there are fourclasses of indications which are defined as follows:A. SingleB. Multiple unalignedC. Multiple alignedD. Intersection of surfaces (threads, corners, fillets, etc.)4. I

7、dentification4.1 The types of discontinuity indications covered by thesereference photographs are listed and described in Table 1. Eachtype of discontinuity indication is designated by a Romannumeral. The class of indication is designated by the letters Athrough D. Individual photographs within type

8、 and class areidentified by numbers. Each reference photograph is, therefore,identified with the proper Roman numeral, letter, and number.5. Method of Preparation5.1 The reference photographs were reproduced from mas-ter photographs which are the property of ASTM. The photo-graphs retain the origina

9、l photographic contrast.6. Basis for Use of Reference Photographs6.1 These reference photographs are intended for use whenspecified in the inquiry, contract, order material specification,or applicable code, and when the severity is mutually agreedupon between the manufacturer and the purchaser. It i

10、srecognized that it is impossible to rigidly interpret indicationsfrom a set of photographic references. Consequently, there is aneed for close cooperation between manufacturer and pur-chaser.6.2 Zones of inspection and severity levels in each zoneshall be shown on applicable drawings or otherwise s

11、pecified.Unless otherwise specified all accessible surfaces shall beexamined.6.3 These reference photographs are intended to depictpenetrant indications of surface discontinuities. They are notintended to indicate the depth of such discontinuities.6.4 Applicable penetrant examination methods and tec

12、h-niques are described in the latest issue of Test Method E165.7. Keywords7.1 discontinuities; liquid penetrant indications; liquid pen-etrant inspection; penetrant inspection; penetrant examination;photographs; reference photographs1These reference photographs are under the jurisdiction of ASTM Com

13、mitteeE07 on Nondestructive Testing and are the direct responsibility of SubcommitteeE07.03 on Liquid Penetrant and Magnetic Particle Methods.Current edition approved June 1, 2013. Published June 2013. Originallyapproved in 1971. Last previous edition approved in 2008 as E433 71 (2008).DOI: 10.1520/

14、E0433-71R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from ASTM Headquarters. Order ADJE0433

15、.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1FIG. 1 Example of Type I, Class A, IndicationFIG. 2 Example of Type I, Class B, IndicationE433 71 (2013)2FIG. 3 Example of Type I, Class C, IndicationFIG. 4 Example of Type I, Class D,

16、IndicationE433 71 (2013)3FIG. 5 Example of Type II, Class A, IndicationFIG. 6 Example of Type II, Class B, IndicationE433 71 (2013)4FIG. 7 Example of Type II, Class C, IndicationFIG. 8 Example of Type II, Class D, IndicationTABLE 1 Reference Photographs, Indication TypesType Class Description Fig. N

17、o.I A single I-A1, 2B multiple unaligned I-B1, 2, 3, 4C multiple aligned I-C1, 2D intersection of surfaces (threads, corners,fillets, etc.)I-D1II A single II-A1, 2, 3, 4B multiple unaligned II-B1, 2, 3C multiple aligned II-C1, 2, 3, 4D intersection of surfaces (threads, corners, II-D1, 2, 3, 4, 5fil

18、lets, etc.)E433 71 (2013)5ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infrin

19、gement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard

20、 or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views

21、 known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).E433 71 (2013)6