ASTM E580 E580M-2011be1 6250 Standard Practice for Installation of Ceiling Suspension Systems for Acoustical Tile and Lay-in Panels in Areas Subject to Earthquake Ground Motions《在遭.pdf

1、Designation: E580/E580M 11b1Standard Practice forInstallation of Ceiling Suspension Systems for AcousticalTile and Lay-in Panels in Areas Subject to EarthquakeGround Motions1This standard is issued under the fixed designation E580/E580M; the number immediately following the designation indicates the

2、 yearof original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Depa

3、rtment of Defense.1NOTESection 4.2.2 was editorially revised in August 2013.1. Scope*1.1 This practice covers the installation of suspended sys-tems for acoustical tile and lay-in panels and their additionalrequirements for two groups of buildings that are constructedto resist the effects of earthqu

4、ake motions as defined by ASCE7 and the International Building Code. These groupings are forSeismic Design Category C and Seismic Design Categories D,E and F.1.2 The authority having jurisdiction shall determine theapplicability of this practice.1.3 Specification C635 and Practice C636 cover suspens

5、ionsystems and their installation without special regard to seismiclateral restraint needs. They remain applicable and shall befollowed when this practice is specified.1.4 Ceilings less than or equal to 144 square feet andsurrounded by walls connected to the structure above areexempt from the requir

6、ements of this practice.1.5 This practice is not intended to stifle research anddevelopment of new products or methods. This practice is notintended to prevent the installation of any material or prohibitany design or method of construction not prescribed in thispractice, provided that any such alte

7、rnative has been substan-tiated by verifiable engineering data or full-scale dynamictesting that is acceptable to the authority having jurisdiction.1.6 Ceiling areas of 1000 ft292.9 m2 or less shall beexempt from the lateral force bracing requirements of 5.2.8.1.7 Ceilings constructed of gypsum boar

8、d which is screw ornail attached to suspended members that support a ceiling onone level extending from wall to wall shall be exempt from therequirements of this practice.1.8 Free floating ceilings (those not attached directly to anystructural walls) supported by chains or cables from thestructure a

9、re not required to satisfy the seismic force require-ments provided they meet the following requirements:1.8.1 The design load for such items shall equal 1.4 timesthe vertical operating weight.1.8.2 Seismic interaction effects shall be considered inaccordance with 5.7.1.8.3 The connection to the str

10、ucture shall allow a 360range of motion in the horizontal plane.1.9 The values stated in either inch-pound or SI units are tobe regarded as standard. Within the text, the SI units are shownin brackets. The values stated in each system are not exactequivalents; therefore, each system shall be used in

11、dependentlyof the other. Combining values from the two systems result innonconformance with the specification.1.10 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safe

12、ty and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C635 Specification for the Manufacture, Performance, andTesting of Metal Suspension Systems for Acoustical Tileand Lay-in Panel CeilingsC636 Practice for Install

13、ation of Metal Ceiling Suspension1This practice is under the jurisdiction of ASTM Committee E33 on Buildingand Environmental Acoustics and is the direct responsibility of SubcommitteeE33.04 on Application of Acoustical Materials and Systems.Current edition approved Nov. 1, 2011. Published November 2

14、011. Originallyapproved in 1976. Last previous edition approved in 2011 as E580 11a1. DOI:10.1520/E0580_E0580M-11BE01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer t

15、o the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1Systems for Acoustical Tile and Lay-In Panels2.2 Other Standards

16、:ASCE 7 Minimum Design Loads for Buildings and OtherStructures3CISCA Recommendations for Direct-hung Acoustical Tileand Lay-in Ceilings, Seismic Zones 0-24CISCA Guidelines for Seismic Restraint for Direct HungSuspended Ceiling Assemblies, Seismic Zones3 earthquake; seismic; seismic re-straint; suspe

17、nded ceilingAPPENDIX(Nonmandatory Information)X1. COMMENTARYX1.1 Recommendations in previous versions of this practicewere based in part on testing done in the 1980s. This, coupledwith general observations from the earthquake prone areas inCalifornia have lead to the original practice.X1.2 Actual ea

18、rthquake experience (most notablyNorthridge and Loma Prieta earthquakes) has shown that threemain things are critical for good performance of ceilingsystems during earthquakes which are:X1.2.1 Independent safety wires on light fixtures to preventdropout,X1.2.2 Minimum strength requirements for splic

19、es andcross/runner/main runner intersections, andX1.2.3 Spreader bars and independent support of suspen-sion member terminal ends at wall closures which preventpanel dropout if the perimeter suspension terminal end slips offof the closure support ledge.X1.3 These observations have lead to the requir

20、ement forsafety wires on light fixtures and minimum connectionstrengths in Practice E580/E580M. This also led to the require-ment for 2-in. 50 mm perimeter support ledger and therequirement for independent support of terminal ends ofsuspension members.X1.4 Advent of International Building Code has r

21、aised theawareness of seismic installation requirements in areas withinthe United States where these requirements traditionally werenot a concern.X1.5 The introduction of non-traditional ceiling made ofwood and metal, as well as ceilings that do not use traditionaltee bar suspension systems, has lea

22、d to a need for an expansionof the prescriptive installation requirements. There has beenalso a general concern over the interaction of the ceiling systemwith HVAC components, lights and sprinklers. This coupledwith the coming of next generation of performance basedseismic codes has lead to new inte

23、rest in clear and conciserequirements for installation of ceiling systems. The result isthis current rewrite of this practice.SUMMARY OF CHANGESCommittee E33 has identified the location of selected changes to this standard since the last issue (E580/E580M11a) that may impact the use of this standard

24、. (Approved November 1, 2011)(1) Sections 4.4.3, 4.4.4, and 4.4.5 were revised. (2) Sections 5.3.4, 5.3.5, and 5.3.6 were revised.Committee E33 has identified the location of selected changes to this standard since the last issue (E580/E580M11) that may impact the use of this standard. (Approved May

25、 15, 2011)(1) Sections 4.2.5, 4.3.2, 4.5.1, 4.5.2, 5.2.4, 5.2.7.2, 5.4.1, and5.4.2were revised.E580/E580M 11b19Committee E33 has identified the location of selected changes to this standard since the last issue (E580/E580M10a) that may impact the use of this standard. (Approved March 15, 2011)(1) 4.

26、1.2 was revised.Committee E33 has identified the location of selected changes to this standard since the last issue (E580/E580M10) that may impact the use of this standard.(1) Added 1.4 and renumbered existing 1.41.9 to 1.5-1.10 andrenumbered existing 1.7.1, 1.7.2, and 1.7.3 to 1.8.1, 1.8.2, and1.8.

27、3.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, a

28、re entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional stand

29、ardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Commi

30、ttee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).E580/E580M 11b110