ASTM E870-1982(2013) 6250 Standard Test Methods for Analysis of Wood Fuels《木材燃料分析的标准试验方法》.pdf

1、Designation: E870 82 (Reapproved 2013)Standard Test Methods forAnalysis of Wood Fuels1This standard is issued under the fixed designation E870; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in

2、parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 These test methods cover the proximate and ultimateanalysis of wood fuels and the determination of the grosscaloric value of wood fuels sampled a

3、nd prepared by pre-scribed test methods and analyzed according to ASTM estab-lished procedures. Test methods as herein described may beused to establish the rank of fuels, to show the ratio ofcombustible to incombustible constituents, to provide the basisfor buying and selling, and to evaluate for b

4、eneficiation or forother purposes.1.2 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limita

5、tions prior to use.2. Referenced Documents2.1 ASTM Standards:2D1102 Test Method for Ash in WoodE711 Test Method for Gross Calorific Value of Refuse-Derived Fuel by the Bomb Calorimeter (Withdrawn2011)3E775 Test Methods for Total Sulfur in the Analysis Sampleof Refuse-Derived FuelE777 Test Method for

6、 Carbon and Hydrogen in the AnalysisSample of Refuse-Derived FuelE778 Test Methods for Nitrogen in the Analysis Sample ofRefuse-Derived FuelE871 Test Method for Moisture Analysis of ParticulateWood FuelsE872 Test Method for Volatile Matter in the Analysis ofParticulate Wood Fuels3. Terminology3.1 pr

7、oximate analysisan assay of the moisture, ash,volatile matter, and fixed carbon as determined by prescribedtest methods. Other constituents such as sulfur and phosphorusare not included.3.2 ultimate analysisthe determination of carbon andhydrogen in the material, as found in the gaseous products ofi

8、ts complete combustion, the determination of sulfur, nitrogen,and ash in the material as a whole, and the calculation ofoxygen by difference.4. Significance and Use4.1 These test methods of analysis described herein can beused for the proximate analysis, ultimate analysis, and thedetermination of th

9、e gross caloric value of wood fuels.5. Procedure5.1 MoistureMethod E871.5.2 AshTest Method D1102.5.3 Volatile MatterTest Method E872.5.4 Fixed CarbonThe fixed carbon is a calculated value. Itis the resultant of the summation of percentage moisture, ash,and volatile matter subtracted from 100. All pe

10、rcentages shallbe on the same moisture reference base.5.5 Carbon and HydrogenTest Method E777.5.6 SulfurTest Methods E775.5.7 NitrogenTest Methods E778.5.8 OxygenThe oxygen is a calculated value. It is theresultant of the summation of percentages carbon, hydrogen,sulfur, nitrogen, and ash subtracted

11、 from 100. All percentagesshall be on the same moisture reference base.5.9 Gross Calorific ValueTest Method E711.6. Precision and Bias6.1 The precision and bias of the test methods describedherein are contained in these individual test methods.7. Keywords7.1 biomass; bulk density; densified particul

12、ate biomass;green tree chip; hogged fuel; particulate wood fuel; pellets;proximate; sawdust; ultimate; volatile matter1These test methods are under the jurisdiction of ASTM Committee E48 onBioenergy and Industrial Chemicals from Biomass and are the direct responsibilityof Subcommittee E48.05 on Biom

13、ass Conversion.Current edition approved June 1, 2013. Published June 2013. Originallyapproved in 1982. Last previous edition approved in 2006 as E870 82(2006). DOI:10.1520/E0870-82R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm

14、.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428

15、-2959. United States1ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringemen

16、t of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or f

17、or additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views know

18、n to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).E870 82 (2013)2