ASTM F1019M-2000(2012) Standard Specification for Steel Deck Gear Stowage Box [Metric]《钢制甲板机械装载箱的标准规范 (米制)》.pdf

1、Designation: F1019M 00 (Reapproved 2012) An American National StandardStandard Specification forSteel Deck Gear Stowage Box Metric1This standard is issued under the fixed designation F1019M; the number immediately following the designation indicates the year oforiginal adoption or, in the case of re

2、vision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the design, material, andmanufacture of steel deck gear stowage boxes.1.

3、2 This specification shall not be used for life preserver orpyrotechnic stowage.1.3 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.2. Referenced Documents2.1 ASTM Standards:2A36/A36M Specification for Carbon Structural SteelA1

4、23/A123M Specification for Zinc (Hot-Dip Galvanized)Coatings on Iron and Steel Products2.2 Other Documents:ABS Rules for Building and Classing Steel Vessels3SSPC Specification 64AWS D1.1 Structural Welding Code53. Classification3.1 Deck Gear Stowage Boxes, shall be the following types:3.1.1 Type ICo

5、nforming to all dimensions in Fig. 1, Fig. 2,Fig. 3, Fig. 4, Fig. 5, Fig. 6, Fig. 7, Fig. 8, and Fig. 9.3.1.2 Type IIConforming only to Fig. 1 configuration andmeeting the requirements of Sections 4-7, dimensions andmaterial specification made to fit unique requirements ofcustomer.4. Ordering Inform

6、ation4.1 Order using this ASTM designation, year of issue, andtype.5. Materials and Manufacture5.1 Materials:5.1.1 The steel for the deck box shall be in accordance withSpecification A36/A36M.5.1.2 Nuts, bolts, and washers shall be corrosion-resistantmaterials.5.1.3 Materials used in construction of

7、 this box and itspackaging shall be free of asbestos and cadmium.5.2 Manufacture:5.2.1 Stowage boxes shall be constructed in accordancewith figures appearing in this standard.5.2.2 Welding shall be in accordance with ABS Rules forBuilding and Classing Steel Vessels or AWS D1.1 StructuralWelding Code

8、 unless otherwise specified.6. Dimensions and Tolerances6.1 Dimensions are as indicated.6.2 Tolerance1.5 mm (6116 in.).7. Workmanship, Finish, and Appearance7.1 The entire assembly shall be free of weld spatter, slag,splinters, sharp edges, projections, and other defects that maybe hazardous to pers

9、onnel.7.2 The box shall be cleaned after assembly to a commercialfinish in accordance with SSPC-SP6.7.3 All surfaces except gratings and covers shall be coatedwith one coat of commercial quality anticorrosive, lead-free,chromate-free primer to a minimum dry film thickness of 50m.7.4 Gratings and cov

10、ers shall be galvanized in accordancewith Specification A123/A123M.8. Keywords8.1 box; deck gear stowage boxes; locker; marine; marinestowage boxes; ship; stowage boxes1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility o

11、f Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved Oct. 1, 2012. Published October 2012. Originallyapproved in 1986. Last previous edition approved in 2006 as F1019M 00 (2006).DOI: 10.1520/F1019M-00R12.2For referenced ASTM standards, visit the ASTM website, www.astm.org,

12、orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American Bureau of Shipping, ABS Plaza, 16855 NorthchaseDr., Houston, TX 77060.4Available from Society for Protecti

13、ve Coatings (SSPC), 40 24th St., 6th Floor,Pittsburgh, PA 15222-4656.5Available from American Welding Society, 550 N.W. Le Jeune Rd., Miami, FL33126.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1FIG. 1 Steel Deck Gear Stowage BoxFIG

14、. 2 HingeFIG. 3 HaspF1019M 00 (2012)2FIG. 4 Cover StayF1019M 00 (2012)3FIG. 5 RodFIG. 6 HandleF1019M 00 (2012)4FIG. 7 FlangeFIG. 8 FlangeF1019M 00 (2012)5FIG. 9 Box MountingF1019M 00 (2012)6ASTM International takes no position respecting the validity of any patent rights asserted in connection with

15、any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technic

16、al committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration

17、 at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbo

18、r Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F1019M 00 (2012)7