ASTM F1041-2002(2008) Standard Guide for Squeeze-Off of Polyolefin Gas Pressure Pipe and Tubing《聚烯烃燃气压力管和管道的燃气排除的标准指南》.pdf

1、Designation: F 1041 02 (Reapproved 2008)An American National StandardStandard Guide forSqueeze-Off of Polyolefin Gas Pressure Pipe and Tubing1This standard is issued under the fixed designation F 1041; the number immediately following the designation indicates the year oforiginal adoption or, in the

2、 case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide describes general procedures for squeeze-offof polyolefin gas pressure pipe

3、and tubing. Pipe and squeezetool manufacturers shall be requested to supply recommenda-tions for squeeze-off with materials or products.1.2 Governing codes and project specifications should beconsulted. Nothing in this document should be construed asrecommending practices or systems at variance with

4、 governingcodes and project specifications.1.3 This guide covers squeeze-off of polyolefin pipe andtubing in accordance with Specification D 2513.1.4 Where applicable in this guide, “pipe” shall mean “pipeand tubing.”1.5 UnitsThe values stated in inch-pound units are to beregarded as the standard. T

5、he values given in parentheses aremathematical conversions to SI units, which are provided forinformation only and are not considered the standard.1.6 This standard does not purport to address all of thesafety problems, if any, associated with its use. It is theresponsibility of the user of this sta

6、ndard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 2513 Specification for Thermoplastic Gas Pressure Pipe,Tubing, and FittingsF 1734 Practice for Qualification of a Combinati

7、on ofSqueeze Tool, Pipe, and Squeeze-Off Procedures to AvoidLong-Term Damage in Polyethylene (PE) Gas Pipe2.2 Other Standards:GRI-92/0147.2 Volume 2: Technical Reference on Squeeze-off of Polyethylene Gas Pipes33. Significance and Use3.1 Squeeze-off is a technique used to control the flow ofgas thro

8、ugh a pipe by the compressing action of a mechanicalor hydraulic device. Squeeze-off may be used to reduce theflow of gas to an acceptable rate.3.2 Proper squeeze-off procedures result in significant timesaving in the reduction of gas flow in an emergency and in themaintenance and operation, or both

9、, of a gas distributionsystem. Improper squeeze-off can cause damage to the pipe orcreate a safety hazard, or both.4. Operator Experience4.1 Each squeeze-off shall be made in accordance withwritten procedures in accordance with Practice F 1734, thathave been proven to produce safe squeeze-off. The p

10、ersonactually responsible for the squeeze-off shall ensure thatdetailed procedures are developed in conjunction with theowner of the pipe system, the manufacturer of the pipe, and themanufacturer of the squeeze-off tools. These procedures shallinclude safety precautions to be followed and are to be

11、issuedbefore actual squeeze-off operations commence.4.2 Skill and knowledge on the part of the operator arerequired to control the flow of gas to achieve a safe squeeze-off. This skill and knowledge shall be obtained by makingsqueeze-offs in accordance with written procedures in accor-dance with Pra

12、ctice F 1734.5. Pipe and Conditions5.1 In order to obtain proper squeeze-off, it is necessary toconsider the pipe diameter, wall thickness, pipe material,internal pressure, squeeze tool(s), squeeze-off procedure andenvironmental conditions. The user shall request the pipemanufacturer to supply speci

13、fic recommendations for thesqueeze-off of the manufacturers product based upon the1This guide is under the jurisdiction of ASTM Committee F17 on Plastic PipingSystems and is the direct responsibility of Subcommittee F17.60 on Gas.Current edition approved March 1, 2008. Published June 2008. Originall

14、yapproved in 1987. Last previous edition approved in 2002 as F 1041 02.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe AST

15、M website.3GRI Document Fulfillment Center, 1510 Hubbard Dr. Batavia, IL 60510.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.evaluation procedures outlined in Practice F 1734 with addi-tional considerations for internal pressure an

16、d ambient tem-perature. The operator shall exercise caution during coldtemperatures because the pipe may be more susceptible tosqueeze off damage.6. Apparatus6.1 Tools to squeeze-off polyolefin gas pressure pipe andtubing shall conform to the requirements of F 1563.7. Procedure7.1 Proper squeeze-off

17、 procedures developed in accordancewith Practice F 1734 shall address safety considerations, toollocation, tool operation, tool removal, and post squeeze-offconsiderations.7.2 Safety ConsiderationsPressure control situations re-quiring squeeze-off may involve working in the vicinity ofescaping gas.

18、Consider the possibility and potential hazard ofstatic electricity and observe safety precautions. Safety precau-tions regarding static electricity generally include performingthe squeeze-off in operation in separate bellhole isolated fromthe blowing gas, grounding the squeeze-off tool and applying

19、asoapy water solution and wet nonsynthetic cloth (such ascotton or burlap material) or commercially available electro-static discharge fluid and polyethylene tape wrap to the pipesurface to provide for dissipation of static charge to the ground.Check the squeeze-off tool prior to use to ensure it is

20、 thecorrect size, is properly functioning, and is properly adjustedfor the squeeze-off to be done.7.3 Tool LocationCenter the squeeze-off tool on andsquare to the pipe. This will allow the pipe to flatten freelywithout jamming against the tool frame or abutments. Locatethe squeeze-off tool at least

21、three pipe diameters or 12 in. (305mm), whichever is greater, from any fusion joint (1.5 diametersfor butt-fusion joint) or mechanical fitting.7.4 Tool OperationOperate the squeeze-off tool at a rateslow enough to allow stress relaxation in the pipe to occur.Experience indicates that compression rat

22、es of 2 in. per min. orless are appropriate. This is particularly helpful when pipebecomes stiff in cold weather. Squeeze the pipe until the flowof gas ceases or the mechanical stop is contacted, whichevercomes first. Continuing to operate the squeeze-off tool beyondthis point can cause pipe or tool

23、 damage. When the squeezed-off position is reached, on some tools, a mechanical lock-offdevice must be manually engaged.7.5 Tool RemovalRemove the squeeze-off tool in a con-trolled manner. If the tool has a mechanical lock-off device,disengage it. Avoid sudden release of mechanical or hydraulicpress

24、ure. Controlled release is necessary so flow control maybe quickly reestablished if required. A release rate of 0.5in./min or less should be maintained to prevent pipe materialdamage. Rerounding the pipe is an option which should beexercised on the basis of improvement in gas flow or otherconcerns,

25、rather than damage mitigation. If rerounding ispreformed, reround the pipe by rotating the squeeze-off tool90 and applying enough force to round the pipe or by using aspecial tool designed for this purpose.7.6 Post Squeeze-off ConsiderationsAfter the squeeze-offtool has been removed, inspect the squ

26、eezed section for anydamage. Procedures should include actions to be taken ifdamage is found. Procedures should not allow the same area tobe squeezed off more than once. When an emergency conditionrequires squeeze-off without regard for possible pipe damage,the procedure should include actions to be

27、 taken based on thelikelihood the pipe has been damaged.8. Keywords8.1 damage; pipe; polyolefin; squeeze-offASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised t

28、hat determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapp

29、roved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you

30、feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 1041 02 (2008)2