ASTM F1071-1994(2018) Standard Specification for Expanded-Metal Bulkhead Panels.pdf

1、Designation: F1071 94 (Reapproved 2018) An American National StandardStandard Specification forExpanded-Metal Bulkhead Panels1This standard is issued under the fixed designation F1071; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision

2、, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers steel expanded-metal bulkheadpanels suitable for use in storerooms, shops, and

3、 as protectionagainst personnel hazards.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This international standard was developed

4、 in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Document

5、s2.1 ASTM Standards:2A36/A36M Specification for Carbon Structural SteelD3951 Practice for Commercial Packaging2.2 Other Documents:ABS Rules for Building and Classing Steel Vessels3AWS D1.1 Structural Welding Code43. Classification3.1 Bulkhead panels are furnished in three types as follows.3.1.1 Type

6、 IUniversal bulkhead panels for use as either aright-hand or left-hand panel.3.1.2 Type IIRight-hand bulkhead panel.3.1.3 Type IIILeft-hand bulkhead panel.3.2 Bulkhead panels are furnished in two classes as follows.3.2.1 Class ABulkhead panels, 2 ft (610 cm).3.2.2 Class BBulkhead panels, 3 ft (915 c

7、m).3.3 Bulkhead panels Types II and III, Class A only, arefurnished in three sizes as follows.3.3.1 Size 176 in. (195 cm) high.3.3.2 Size 264 in. (165 cm) high.3.3.3 Size 340 in. (100 cm) high.4. Ordering Information4.1 Orders for expanded-metal panels under this specifica-tion shall include this sp

8、ecification number, type, class, andsize.5. Materials and Manufacture5.1 MaterialsSee Table 1.5.2 Manufacture:5.2.1 Welding shall be in accordance with AWS D1.1 or theABS Rules for Building and Classing Steel Vessels.5.2.2 Panels shall be welded and fabricated as shown inFigs. 1-6.5.2.3 After panels

9、 have been shipped to the contractor, thepanels will be assembled into bulkheads by welding or boltingby others.6. Tolerances6.1 Tolerances6116 in. (1.5 mm).7. Workmanship, Finish, and Appearance7.1 Expanded-metal panels shall be free from all cracks,burrs, sharp edges, and other defects.7.2 The pan

10、el manufacturer shall apply a nonhazardouscorrosion-inhibiting primer coating to all panel assemblies.8. Packaging and Package Marking8.1 Expanded-metal bulkhead panels shall be individuallypacked for shipment and storage in accordance with PracticeD3951.8.2 In addition to any special marking requir

11、ed by thecontract or purchase order, each expanded-metal panel packageshall be marked in accordance with Practice D3951.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Mach

12、inery.Current edition approved April 1, 2018. Published May 2018. Originallyapproved in 1987. Last previous edition approved in 2012 as F1071 94 (2012).DOI: 10.1520/F1071-94R18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. F

13、or Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American Bureau of Shipping (ABS), ABS Plaza, 16855Northchase Dr., Houston, TX 77060, http:/www.eagle.org.4Available from American Welding Society (AWS), 8669 NW 36 St.

14、, #130,Miami, FL 33166-6672, http:/www.aws.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Dec

15、ision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.19. Keywords9.1 bulkhead panels; expanded-metal bulkhead panels; pan-els; steel bulkhead panelsTABLE 1 Expanded-Metal Bulkh

16、ead Panel MaterialsNOTE 11 in. = 25.4 mm.Item Number Description1 Frame angle, 114 114 14 in., Specification A36/A36M2 Brace flatbar,14 2 in., Specification A36/A36M3 Expanded metal 13-gage thick 12-in. flat pattern 23 in. wide, Specification A36/A36M4 Expanded metal 13-gage thick 12-in. flat patter

17、n 35 in. wide, Specification A36/A36MNOTE 11 in. = 25.4 mm.FIG. 1 Expanded-Metal Bulkhead PanelType 1, Class A, Size 1F1071 94 (2018)2NOTE 11 in. = 25.4 mm.FIG. 2 Expanded-Metal Bulkhead PanelType I, Class B, Size 1NOTE 1Type IIILeft hand not shown.NOTE 21 in. = 25.4 mm.FIG. 3 Expanded-Metal Bulkhea

18、d PanelType II, Class A, Size 1NOTE 1Type IIILeft hand not shown.NOTE 21 in. = 25.4 mm.FIG. 4 Expanded-Metal Bulkhead PanelType II, Class B, Size 1F1071 94 (2018)3ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this s

19、tandard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be re

20、viewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of therespons

21、ible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West

22、Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights

23、 to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 11 in. = 25.4 mm.FIG. 5 Expanded-Metal Bulkhead PanelType II, Class A, Size 2NOTE 11 in. = 25.4 mm.FIG. 6 Expanded-Metal Bulkhead PanelType II, Class A, Size 3F1071 94 (2018)4