1、Designation: F 1084 08Standard Guide forSampling Oil/Water Mixtures for Oil Spill RecoveryEquipment1This standard is issued under the fixed designation F 1084; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revisi
2、on. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide is intended for sampling flowing or station-ary oil/water mixtures. It is intended for use with oil spillrecovery devi
3、ces either in testing or in documentation of fieldperformance.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is th
4、eresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 1796 Test Method for Water and Sediment in Fuel Oils bythe Centrifuge Method (Labora
5、tory Procedure)D 4007 Test Method for Water and Sediment in Crude Oilby the Centrifuge Method (Laboratory Procedure)F 625 Practice for Classifying Water Bodies for Spill Con-trol Systems3. Significance and Use3.1 This guide provides techniques for obtaining represen-tative samples of oil and water m
6、ixtures. This information isnecessary in the calculation of oil recovery efficiency and oilrecovery rates for oil collection devices.3.2 Sampling Stationary MixturesWhen recovered oil/water mixtures are contained within a holding tank and therelative oil content of the recovered fluid is needed, the
7、sampling technique is somewhat dependent on the container.Two techniques are outlined in this guide. If the container hasa flat bottom with straight sides perpendicular to the base (ornearly so), either stationary technique can be implemented,with the stratified sampling method preferred. If the con
8、taineris irregular in either the horizontal or vertical cross section, themixing method is preferred.3.3 Sampling Flowing MixturesTo sample flowing mix-tures containing both oil and water, turbulence is induced, tocreate a homogenous mixture while sampling. The oil contentin the sample taken from th
9、e flowing stream can then be usedto quantify the performance-rating criterion (see ProcedureSection of Test Method D 1796).4. Number of Samples4.1 Take a minimum of four samples under each set ofconditions to average results and store the samples separately.In less ideal sampling conditions, take ad
10、ditional samples.5. Containers5.1 A dry, water-washed glass sample container.6. Labeling6.1 Mark the sample container with the source, type of oil,date and time of sampling, the name of the person taking thesample, and a sample number. Require water and oil-resistantlabeling. If several receiving co
11、ntainers are to be sampled, theymust be identified and the samples marked for later coordina-tion.7. Preservation and Storage7.1 The samples do not require special treatment to preservetheir integrity other than ensuring that they remain sealed untilanalyzed. Note date and time of analysis for each
12、sample.8. Procedure8.1 Baseline DataThe test fluids may be crude, refined, orsynthetic oils. Record type, specific gravity, viscosity, andtemperature of each oil together with the environmentalconditions (see Practice F 625), air temperature, and slickthickness beyond the influence of the recovery e
13、quipment foreach test point.8.2 Sampling from a ContainerThis procedure is intendedfor taking a representative sample of collected fluids held in acontainer. When sampling containers, it is advisable to remove1This guide is under the jurisdiction of ASTM Committee F20 on HazardousSubstances and Oil
14、Spill Response and is the direct responsibility of SubcommitteeF20.12 on Removal.Current edition approved Sept. 15, 2008. Published September 2008. Originallyapproved in 1987. Last previous edition approved in 2002 as F 1084 90 (2002).2For referenced ASTM standards, visit the ASTM website, www.astm.
15、org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.as much of
16、the aqueous phase as possible prior to sampling. Ifthis is possible, measure and record the volume of waterremoved, which will contain dissolved hydrocarbons, for latercalculation of the relative oil/water composition. The precisionof the measurement will improve with removal of the aqueousphase.8.2
17、.1 Mixing Method:8.2.1.1 Mix the container of stratified oil and water usingany method which will achieve homogeneity during sampling(high-speed propeller, liquid jet, or homogenizing pump).Operate the mixer for a minimum of 5 min. Longer mixingtimes are preferable to ensure homogeneity.NOTE 1Althou
18、gh this mixing method has been geared toward electricmixers, alternate mixing methods could be used (air or liquid mixing jets,homogenizing pumps), so long as a homogeneous mixture of the entirevolume is created. Immediately after mixing, obtain a representativesample of the homogeneous mixture by l
19、owering a 250 to 500-mLsmall-mouthed bottle (from which the cap has been removed) at a constantslow rate from the surface of the mixture to the bottom of the tank.Immediately remove the bottle by slowly raising it through the mixture. Ifnecessary, repeat the process to ensure that at least 50 mL of
20、sample willbe available for laboratory analysis. Do not fill the bottle to the top.8.2.1.2 LimitationsThe size of the sampled fluid containeris limited by the mixing capability available for thoroughlyhomogenizing the oil and water. Mixtures where the relative oilcontent is less than 20 % probably w
21、ill not form a stableemulsion for sampling; making this method inappropriate forthese mixtures.NOTE 2Certain oils (N-dimethylformamide, military jet engine fuel,DMF, JP5) will not form stable emulsions. Speed is important in thesecases as the homogeneity of the mixture diminishes rapidly.8.2.2 Nonmi
22、xing Method:8.2.2.1 Where recovered oil/water mixtures cannot be ho-mogenized or the emulsion formed is not easily broken, inserta stratified sampler into the nonmixed fluids to obtain a crosssection of the fluids. Construct the stratified sampler as shownin Fig. 1.8.2.2.2 Stratified Mixture Samplin
23、gPlace the entire sam-pler within the mixture to be sampled, with the outer sheath inthe raised (open) position to expose the inner core. Lower theouter sheath to capture a set of samples in the annularsegments. Remove the entire sampler, wipe clean, and draineach sample container through a clean fu
24、nnel.8.2.2.3 LimitationsSampling with this device limits thesize of the sampled tank. The physical workings of the samplerdictate that the tank cannot be greater in depth than the heightthat the sample taker can comfortably reach above the top ofthe tank. Movement of the tank can give nonrepresentat
25、ivesamples because of the rolling oil/water interface. Use on smallvessels in the high seas requires that additional samples betaken and results averaged. The sampler must be thoroughlycleaned between sample takings.NOTE 3If the container is irregular in vertical cross section, thesegments within th
26、e sample should not be analyzed as a whole. Eachsegment must be analyzed separately and averaged on a representative-volume-weight basis. Each segment must be large enough to capture a 50mL sample for analysis.8.3 Sampling from a FlowWhen it is necessary to samplea flowing stream, eliminate the poss
27、ibility of multilayer orstratified flow and bring the stream into a turbulent flowcondition.8.3.1 Position a static mixer (sometimes called an in-line ormotionless mixer) in the skimmer discharge by-pass line, onthe high-pressure side of the recovery pump. Immediately afterthe static mixer, install
28、a sampling port shaped like a fixed Pitottube (see Fig. 2) at the pipe center. It should be accessible andeasy to use. Specify the static mixer to produce disperseddroplets having a mean droplet diameter of approximately2000 m at the expected flow rate and oil content. This methodNOTE 1Align holes o
29、n slots in inner and outer sleeve to let sampleinto zones of the sampler. When sampler is closed, holes are covered andsampler is secured.FIG. 1 Stratified Sampler with Construction DetailsFIG. 2 Sampling BypassF1084082will provide a representative sample which can be used todetermine the percentage
30、 of oil in the flowing oil/water mixtureencountered.NOTE 4Because this is a measurement taken over a short timeinterval, it must be considered to be a differential measurement and manysamples must be taken to ensure validity, especially in the start up portionof the oil recovery operation when condi
31、tions are rapidly changing.NOTE 5Although this method requires many samples to be taken, it isadvisable not to keep the sampling port in constant operation. The mixedfluids are, by choice, a dispersion, which should separate readily, but theintentional mixing of the recovered oil and water should be
32、 avoided inongoing oil recovery operation. The mixing elements within the mixermay also cause a significant pressure drop which may be deleterious toskimmer performance. The mixer will be sensitive to debris, particularlystring-like debris (sorbent, seaweed, fishing line) that will tend to wraparoun
33、d the elements. The use of a by-pass parallel to the main flow isrecommended.NOTE 6Sampling ports, lines, or by-passes, should be purged for asuitable time before actual samples are taken.9. Procedure for Determining Percent of Oil in Mixtureby Instruction or Reference9.1 Refer to Test Method D 4007
34、.10. Accuracy10.1 Stationary MixturesThese procedures have been de-veloped with known oil/water mixtures in flat-bottom contain-ers holding less than 2 m3of mixture.10.1.1 Mixing MethodThe comparison of the known oilcontent to that determined using the mixing method yielded amaximum difference of 6
35、% and an average difference of 2 %.The known oil content error was approximately 1 %. The mixmethod will yield results within 7 %.10.1.2 Stratified MethodThe comparison of known oilcontent to the determined oil content yielded a maximumdifference of 6 % and an average of 2 %. When the stratifiedmixt
36、ure is sampled without free-standing water removal, theanalysis is considered to be accurate within 4 %.10.2 Flowing MixturesThe difference between the oilcontent determined with a sample of the total flow by themixing method and the oil content determined by averaging thePitot tube sample results w
37、as 4 %. The maximum differencewas 7 %, which is considered to be the limit of the accuracy inthe method.NOTE 7These procedures have been confirmed with known oilcontent ranging from 10 % to 90 %, but have not undergone completeround-robin testing. The differences between known oil content andanalyze
38、d oil content include the errors of sampling technique, sampleretrieval, and sample analysis.11. Keywords11.1 oil spill; oil spill recovery; oil/water mixturesASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this stand
39、ard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be review
40、ed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible
41、 technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F1084083
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1