ASTM F1141-1993(2004) Standard Specification for Wallcovering《墙面饰层的标准规范》.pdf

1、Designation: F 1141 93 (Reapproved 2004)Standard Specification forWallcovering1This standard is issued under the fixed designation F 1141; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in paren

2、theses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the performance, quality, pack-aging, and marking characteristics of flexible wall covering asa finished product.2. Referen

3、ced Documents2.1 ASTM Standards:F 793 Classification of Wallcovering by Durability Charac-teristics23. Terminology3.1 Definition:3.1.1 wallcoveringa flexible product designed to coverwalls and ceilings for decorative or functional purposes, orboth.3.2 Definitions of Terms Specific to This Standard:3

4、.2.1 backing (substrate)material upon which facing (oran intermediate layer) is applied. Backing is that materialwhich is adhered to the wall.3.2.2 biaspattern running off true horizontal or verticalplane.3.2.3 bolta continuous amount of packaged material con-taining the amount specified on the labe

5、l.3.2.4 facingdecorative material which is applied to anintermediate layer or backing.3.2.5 finished productwallcovering offered to a consumerfor installation.3.2.6 intermediate layermaterial, if any, between thefacing and the backing.3.2.7 lot (batch)the product from a continuous manufac-turing run

6、 having the same appearance and characteristic frombeginning to end.3.2.8 pattern matchthe meeting of all parts and colors ofa pattern at the seams of adjacent strips.3.2.9 pattern repeatthe vertical distance between adjacentmatch points of a pattern.3.2.10 protective layerany material applied to th

7、e facingto enhance performance.3.2.11 registerthe designed meeting of all parts and colorsof a pattern.3.2.12 runa unit of production which may include morethan one lot.3.2.13 secondsfinished material not meeting the qualitycriteria in accordance with Classification F 793 and this speci-fication.3.2

8、.14 selvagean undecorated edge which must betrimmed away to allow for correct pattern match or uniformcontinuity of color.3.2.15 waste edgea decorated edge that must be trimmedaway to allow for correct pattern match or uniformity of color.3.2.16 Shading:3.2.16.1 color variation difference within the

9、 same lot ofwallcovering.3.2.16.2 luster variation difference in gloss level withinthe same lot of wallcovering.3.2.16.3 texture variationdifference in embossing withinthe same lot of wallcovering.3.2.17 split bolta bolt consisting of two or three separatelengths of material.4. Appearance4.1 There s

10、hall be no appreciable difference in shadingexcept on those finished products in which natural decorativecharacteristics are being simulated. These variances must beclearly stated in writing at the point of purchase. To determinewhether there is an appreciable difference, suspend threesequential 8-f

11、t (2.4-m) strips at eye level in a vertical position,as on the wall, under illumination between 100 to 150 fc (1000to 1500 lx), and view the strips from a distance between 4 and8 ft (1.2 and 2.4 m). An appreciable difference is one which isnoticeable when one strip is compared with the others.5. Wal

12、l Preparation and Installation5.1 Basic and correct wall preparation instructions, withparticular attention to wall covering which requires specialwall preparation for its proper installation, shall be included insample books and installation instructions.5.2 Installation instructions shall be in or

13、 with each bolt andbe readily accessible to the installer. It shall be the manufac-turers responsibility to notify consumers of proper installationtechniques when new products are introduced.1This specification is under the jurisdiction of ASTM Committee F15 onConsumer Products and is the direct res

14、ponsibility of Subcommittee F15.15 onWallcoverings.Current edition approved Jan. 1, 2004. Published January 2004. Originallyapproved in 1988. Last previous edition approved in 1998 as 1141 93 (1998).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service

15、 at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.3 The manufacturer shall recommend an adhesiv

16、e, whennecessary, and the products to be used for wall preparation.Recommendation for alternative adhesives and wall prepara-tion products shall be included in the installation instructions.6. Physical Requirements6.1 Each finished product shall be uniform in physicalproperties, in accordance with C

17、lassification F 793 and thisspecification.6.2 All facings and protective layers shall be adheredproperly to backings and intermediate layers and the finishedproduct shall be of such quality that delamination does notoccur during normal installation and use.6.3 Finished products shall not chip, peel,

18、 or flake duringnormal installation and use. (For test methods to determineconformity with this requirement refer to Classification F 793.)6.4 There shall be no more than a18-in. (3.5-mm) variancein pattern match between two 8-ft (2.4-m) strips at midpoint.6.5 Wallcovering shall be free from all sur

19、face flaws,creases, splices, scratches, tears and dirt throughout its entirelength.6.6 Wallcovering shall be free of wrinkles which cannot beremoved in the course of normal installation.6.7 Finished product shall not shrink or expand after instal-lation when installed in accordance with the manufact

20、urersinstructions.6.8 Pretrimmed material shall be trimmed so that no con-trasting backing color will show at the seam when two sheetsare properly installed.6.9 Pretrimmed material shall show no frayed or wavyedges.6.10 All elements of the pattern shall be in register.6.11 The design shall be set at

21、 an angle of 90 to thetrimmed edge.6.12 Split bolts narrow goods shall have no piece shorterthan 9 ft (2.7 m) and shall have an area at least 10 % larger thanspecified on the label. Three lengths are permitted in split boltshaving an area exceeding 100 ft2(9.3 m2). Wide commercialgoods shall have no

22、 piece shorter than 3 yd (2.7 m) andone-half linear yard larger than specified on the label.6.13 The finished product shall have the necessary charac-teristics to adhere the product to the wall when it is installed inaccordance with the manufacturers instructions. (For testmethods to determine confo

23、rmity with this requirement refer toClassification F 793.)7. Inspection and Testing7.1 Manufacturers shall be responsible for testing and in-spection in accordance with this specification and Classifica-tion F 793.7.2 The introduction of new products on the market shall bepreceded by thorough testin

24、g by the manufacturer underrepresentative field conditions. Manufacturers shall validatelaboratory quality control tests against actual field conditions.8. Rejection and Review8.1 Wallcovering that fails to conform to the requirementsof this specification may be rejected by the installer orpurchaser

25、. Rejections shall be reported to the supplier promptlyin person, by phone, or in writing, or any combination thereof.In the event the supplier is unwilling or unable to satisfy thecomplainant, the matter should be referred to the manufacturer.The inspection and test procedures contained in this spe

26、cifica-tion shall be used to determine the conformance of the productto the requirements of this specification. Each manufacturerwho represents a product as conforming to this specificationmay use statistically based sampling plans that are appropriatefor each particular manufacturing process, but s

27、hall keep suchessential records as are necessary to document the claim thatthe requirements of this specification have been met.8.2 Any portion of the item not conforming to this specifi-cation shall be clearly marked as seconds if packaged for resaleat retail.9. Certification9.1 When specified in t

28、he purchase order or contract, amanufacturers or suppliers certification shall be furnished tothe purchaser stating that samples representing each lot of thematerial have been manufactured, tested, and inspected inaccordance with this specification and the requirements havebeen met.10. Product Marki

29、ng10.1 Finished products up to 42 in. (107 cm) in width shallbe labeled with the following information: pattern number, lot(batch) run number, length, width, total area of material(excluding border), supplier name and address and type ofmaterial when appropriate.10.2 Finished products exceeding 42 i

30、n. (107 cm) in widthshall be labeled with the following information: lot (batch),run, length, width, suppliers name and address and type ofmaterial when appropriate.10.3 On a wallcovering where direction of hanging isambiguous, the manufacturer shall indicate the proper directionon each separate len

31、gth.10.4 Bolts classified as seconds shall be prominently labeledas such.10.5 Murals shall be properly numbered for sequence ofsheets. If a numbering sequence is not used, a precise layoutdiagram shall be provided.10.6 A split bolt shall be identified as such.11. Product Packaging and Shipment11.1 T

32、he finished products shall be packaged to preventdamage in shipment.11.2 Shrink wrapping shall not be so tight that it createsproduct damage.11.3 Each case shall not contain more than one split bolt.12. Catalog Information12.1 Sample books shall include length, width and squarefootage of each packag

33、ed bolt.12.2 Each pattern shall be identified as to proper match andrepeat if any.12.3 Sample book shall state that the product conforms tothis specification.F 1141 93 (2004)213. Keywords13.1 backing (substrate); bias; bolt; facing; finished product;intermediate layer; lot (batch); pattern match; pa

34、ttern repeat;protective layer; register; run; seconds; selvage; shading andwaste edge; split bolt; wallcoveringASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advise

35、d that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either re

36、approved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If y

37、ou feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 1141 93 (2004)3