ASTM F1183-1996(2006) Standard Specification for Aluminum Alloy Chain Link Fence Fabric《铝合金链环栅栏结构》.pdf

1、Designation: F 1183 96 (Reapproved 2006)Standard Specification forAluminum Alloy Chain Link Fence Fabric1This standard is issued under the fixed designation F 1183; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last r

2、evision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers aluminum alloy chain linkfence fabric for commercial, industrial, and residential uses.1.2 The va

3、lues stated in inch-pound units are to be regardedas standard. The values in brackets are provided for informa-tion only.2. Referenced Documents2.1 ASTM Standards:2A 700 Practices for Packaging, Marking, and LoadingMethods for Steel Products for ShipmentB211 Specification for Aluminum and Aluminum-A

4、lloyBar, Rod, and Wire2.2 Federal Standards:Fed. Std. No. 123 Marking for Shipment, Civil Agencies32.3 Military Standards:MILSTD129 Marking for Shipment and Storage33. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 chain link fence fabrica fencing material made fromwire helicall

5、y wound and interwoven in such a manner as toprovide a continuous mesh without knots or ties, except in theform of knuckling or of twisting the ends of the wires to formthe selvage of the fabric.3.1.2 diamond countthe number of diamond openingsfrom one edge of the fabric to the other. The diamond co

6、unt ofa given fabric shall begin at the first completed diamond at oneedge and continue to the unfinished (one-half) of full openingat the other edge.3.1.3 knucklinga term used to describe the type of selvageobtained by interlocking adjacent pairs of wire ends and thenbending the wire ends back into

7、 a loop. The loop shall beclosed or nearly closed to a measurement less than the diameterof the wire.3.1.4 twistinga term used to describe the type of selvageobtained by twisting adjacent pairs of wire ends together in aclose helix of 112 machine turns, which is equivalent to threefull twists, and c

8、utting the wire ends at an angle. The wire endsbeyond the twist shall be at least14 in. 6.35 mm long. Thistype of selvage is not used on fabric with a mesh size of lessthan 2 in.4. Ordering Information4.1 Orders for chain link fence fabric purchased to thisspecification shall include the information

9、 given in 4.1.1through 4.1.8.4.1.1 Quantity (Section 13),4.1.2 Size of mesh (Section 7),4.1.3 Size of wire (Section 8),4.1.4 Height of fabric (Section 9),4.1.5 Diamond count, if specified (Section 6),4.1.6 Type of selvage (Section 10),4.1.7 Certification, if required (Section 16), and4.1.8 ASTM desi

10、gnation and year of issue.4.2 All rolls of fencing accepted by the purchaser shall bebilled on the basis of the original footage of the rolls prior tosampling, unless changed by contractual arrangement.NOTE 1An example of a typical ordering description is as follows: 25rolls, 50 ft each, chain link

11、fence fabric, aluminum alloy, 2 in. 50.8 mmmesh, 0.148 in. 3.76 mm wire, 60 in. high, knuckled both selvages, toASTM F 1183 .5. Materials5.1 The wire from which the fabric is woven shall conformto all requirements of alloy 6061, temper T94 described inSpecification B211.6. Weave6.1 The wire shall be

12、 woven throughout in the form ofapproximately uniform square mesh, having parallel sides andhorizontal and vertical diagonals of approximately uniformdimensions. The top and bottom of the fabric shall be knuckledor twisted as specified in Section 10.1This specification is under the jurisdiction of A

13、STM Committee F14 on Fencesand is the direct responsibility of Subcommittee F14.40 on Chain Link Fence andWire Accessories.Current edition approved June 1, 2006. Published June 2006. Originallyapproved in 1988. Last previous edition approved in 2002 as F 1183 - 96(2002).2For referenced ASTM standard

14、s, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave.,

15、Philadelphia, PA 19111-5094, Attn: NPODS.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6.2 A typical diamond count for each standard height isshown in Table 1. Other diamond counts are permissibleprovided that they are consistent w

16、ithin a lot. The purchaserhas the option to specify the diamond count (4.1.5).7. Size of Mesh7.1 The size of mesh shall be as indicated in Table 2.7.2 The permissible variation from the specified size ofmesh shall be 618 in. 3.175 mm for all mesh sizes except 1in. 25.4 mm, and 6116 in. 1.5875 mm for

17、 1-in. 25.4 mmmesh size.7.3 The size of mesh shall be determined by measuring theminimum clear distance between the wires forming the parallelsides of the mesh, and calculated as the average of tworeadings taken at right angles to each other.8. Size of Wire8.1 Chain link fabric shall be fabricated f

18、rom wire diametersas listed in Table 2, with a permissible variation from thespecified diameter of 60.005 in. 0.127 mm.9. Height of Fabric9.1 Chain link fabric shall be furnished in the standardheights shown in Table 2. The height of fabric shall be theoverall dimension from ends of twists or knuckl

19、es. Permissiblevariation from the specified height shall be 61 in. 25.4 mmfor 134 in. 44.45 mm and 2 in. 50.8 mm mesh and 612 in.12.7 mm for 1 in. 25.4 mm mesh.10. Selvage10.1 Unless otherwise specified by the purchaser, fabricswith 2 in. 50.8 mm mesh used in heights 60 in. 1524 mmand under shall be

20、 knuckled at both selvages. Fabric of heights72 in. 1830 mm and above shall be knuckled at one selvageand twisted at the other.10.2 The selvages of all fabrics with meshes of less than 2in. shall be knuckled.NOTE 2Use of twisted selvages for fence fabric under 72 in. 1830mm in height are not recomme

21、nded because of consumer safety consid-erations.11. Breaking Strength11.1 The wire constituting the fabric shall meet the mini-mum breaking strength requirements shown in Table 3.12. Finish12.1 Unless otherwise specified, the fabric shall have a millfinish. The purchaser may specify a caustic-cleane

22、d, or etchedfinish, derived by chemical removal of the wire drawing andweaving lubricants after the fabric is woven.13. Standard Length of Rolls13.1 The standard length of roll shall be 50 ft 15.24 m61 %, except as otherwise agreed upon at the time ofpurchase.13.2 The length of roll shall be determi

23、ned by unrolling aroll of fabric onto a flat surface and then exerting tension byappropriate means to remove all slack. The tension appliedshall not reduce the actual height of the fabric by more than116in./ft 1.5875 mm/m of height or by more than12 in. 12.7mm total, whichever is less.14. Sampling a

24、nd Number of Tests14.1 One roll of every 50 rolls, or fraction thereof, in a lotshall be taken at random as a sample for test purposes. In nocase shall less than two samples be tested, except when the lotis less than 10 rolls, when only one roll shall be selected for thesample.14.2 Sample rolls sele

25、cted shall be inspected for uniformityof weave (6.1), diamond count (6.2), size of mesh (Section 7),size of wire (Section 8), height of fabric (Section 9), selvage(Section 10), tensile strength (Section 11), and length (Section13).14.3 If any specimen fails to meet the requirements of thisspecificat

26、ion, the roll represented by the specimen shall berejected. Two additional rolls shall be inspected, both of whichTABLE 1 Typical Diamond CountA,BDiameter ofWire, in.Size ofMesh, in.Height of Fabric, in.36 42 48 60 72 84 96 108 120 1440.192 2 1012 1212 1312 1712 2012 2412 2712 3112 3412 41120.148 2

27、1012 1212 1312 1712 2012 2412 2712 3112 3412 41120.148 134 3112 3512 3912 47120.148 20232733394553616779AOther diamond counts are permitted. Refer to 6.2 of this specification.BSee Table X1.1 for metric equivalents.TABLE 2 Sizes of Wire and MeshASpecifiedDiameter ofWire, in.WireGaugeSizeSize ofMesh,

28、 in.Height of Fabric, in.0.192 6 2 36, 42, 48, 60, 72, 84, 96, 108,120, 1440.148 9 2 36, 42, 48, 60, 72, 84, 96, 108,120, 1440.148 9 134 . . . . . . 96, 108, 120,1440.148 9 1 36, 42, 48, 60, 72, 84, 96, 108,120, 144ASee Table X1.1 for metric equivalents.TABLE 3 Breaking Strength of WireSpecified Dia

29、meter of Wire,in. mmMinimum Breaking Strength,lbf N0.192 4.880.148 3.761560 6939925 4114F 1183 96 (2006)2shall meet the requirements in every respect; otherwise, the lotrepresented by the samples may be rejected.15. Inspection15.1 Unless otherwise specified in the purchase order orcontract, the manu

30、facturer is responsible for the performanceof all inspection and test requirements specified in this speci-fication. Except as otherwise specified in the purchase order orcontract, the manufacturer may use his own or any othersuitable facilities for the performance of the inspection and testrequirem

31、ents, unless disapproval is expressed by the purchaserat the time the order is placed. The purchaser shall have theright to perform any of the inspection and tests set forth in thisspecification when such inspections and tests are deemednecessary to assure that the material conforms to prescribedreq

32、uirements.16. Certification16.1 When specified in the purchase order or contract, aproducers or suppliers certification shall be furnished to thepurchaser stating that the material was manufactured, sampled,tested, and inspected in accordance with this specification, andhas been found to meet the re

33、quirements. When specified in thepurchase order or contract, a report of the test results shall befurnished.17. Packaging, Marking, and Loading17.1 Each length of chain link fence fabric shall be tightlyrolled and firmly tied. Each roll shall carry a tag describing thetype of material, the specified

34、 wire size and mesh size, and thespecified length and height of fabric in the roll. Compliance ofthe fence fabric with Specification F 1183 shall be marked, aswell as the name or mark of the manufacturer.17.2 Unless otherwise specified, packaging, marking, andloading for shipment shall be in accorda

35、nce with PracticesA 700.17.3 When specified in the contract or order, and for fencefabric being directly procured by or directly shipped to the U.S.government, marking for shipment, in addition to the require-ments specified in the contract or order, shall be in accordancewith MIL-STD-129 for U.S. m

36、ilitary agencies and in accor-dance with Fed. Std. No. 123 for civil agencies.18. Keywords18.1 aluminum alloy chain link fence fabric; chain linkfence, aluminum alloy; fence/fencing materials, chain linkAPPENDIX(Nonmandatory Information)X1. METRIC EQUIVALENTSX1.1 Approximate metric equivalents are g

37、iven in TableX1.1.TABLE X1.1 Approximate Metric Equivalents for Tables 1 and 2Diameters of Wire and Sizes of Mesh Height of Fence Fabricin. mm in. mm0.192 4.88 36 9100.148 3.76 42 107048 122060 15201 25 72 1830134 44 84 21302 50 96 2440108 2740120 3050144 3660F 1183 96 (2006)3ASTM International take

38、s no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own res

39、ponsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be address

40、ed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the

41、 address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 1183 96 (2006)4