ASTM F1331-1991(2002) Standard Practice for Installation Procedures of Vinyl Deck Coverings on Portable Plates in Electrical and Electronic Spaces《电气和电子操作室中可移动板上乙烯铺面覆盖物的安装程序》.pdf

1、Designation: F 1331 91 (Reapproved 2002)An American National StandardStandard Practice forInstallation Procedures of Vinyl Deck Coverings on PortablePlates in Electrical and Electronic Spaces1This standard is issued under the fixed designation F 1331; the number immediately following the designation

2、 indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers the acceptable

3、method for installinginsulated deck covering on portable deck plates.1.2 This deck covering shall be installed, in way of theelectrical and electronic spaces, for marine use.1.3 The values stated in SI (metric) units are to be regardedas the standard. The values in parentheses are for informationonl

4、y.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced

5、 Documents2.1 ASTM Standards:D 1338 Practice for Working Life of Liquid or Paste Adhe-sives by Consistency and Bond Strength2D 2393 Test Method for Viscosity of Epoxy Resins andRelated Components3D 4389 Specification for Finished Glass Fabrics Wovenfrom Rovings4F 150 Test Method for Electrical Resis

6、tance of Conductiveand Static Dissipative Resilient Flooring52.2 Other Documents:Steel Structural Painting Council SP-1163. Requirements3.1 Operations AreaTypical areas for application of theelectric insulating deck covering are:3.1.1 The operating areas in front and rear of power andlighting switch

7、boards, interior-communication switchboards,test switchboards, fire-control switchboards, and shipboardannouncing-systems amplifiers and control panels.3.1.2 The area around electronic equipment which may becontacted by personnel in servicing or tuning energized equip-ment.3.1.3 Vinyl sheets should

8、be confined to the minimum deckareas (generally 0.9 m (3 ft) wide) surrounding the apparatusnecessary to prevent electric shock, and should, unless other-wise specified, be cemented to the deck in lieu of otherspecified deck coverings.3.2 InstallationVinyl Sheets:3.2.1 Installation of deck covering

9、shall be in accordancewith Figs. 1-7, using vinyl sheet and fiberglass binding strips(see Fig. 1 and Fig. 5).1This practice is under the jurisdiction of ASTM Committee F25 on Ships andMarine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting.Current edition approved Marc

10、h 15, 1991. Published June 1991.2Annual Book of ASTM Standards, Vol 15.06.3Discontinued; See 1991 Annual Book of ASTM Standards, Vol 08.02.4Annual Book of ASTM Standards, Vol 07.02.5Annual Book of ASTM Standards, Vol 15.04.6Available from Steel Structures Painting Council (SSPC), 40 24th St., 6thFlo

11、or, Pittsburgh, PA 15222-4656.FIG. 1 Typical Deck Covering Plan ViewFIG. 2 Section “D-D” (See Fig. 1)1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.2.2 Vinyl sheets and fiberglass sheets shall be united at theedges in a rabbet joi

12、nt as shown (see Fig. 7), and such that thefiberglass overlaps at all joints. All rabbeted surfaces shall besmooth and corners sharp and square, such that at installationthe overlapping areas fit firmly and flush. Vinyl shall meetrequirements and tests provided in Test Method F 150.3.3 Adhesive:3.3.

13、1 Vinyl sheets shall be secured to each portable platewith adhesive. Adhesive should not extend beyond edges ofvinyl sheet.3.3.2 Silicone compound, with 1 % liquid catalyst, shouldbe applied between lapping areas in accordance with TestMethod D 1338.3.4 FiberglassGlass fiber base, epoxy resin sheets

14、 fur-nished under this specification (Fig. 1 and Fig. 5), shall be aproduct consisting of plies or layers of cloth or nonwovenparallel aligned fibers bonded with an epoxy resin compound,in accordance with Specification D 4389.3.5 Fastening with Nylon ScrewsFiberglass binding stripsshall be secured t

15、o the deck with nylon screws. A 76-mm(3-in.) wide strip over joints between portable plates shall befastened with a double row of screws. A 38-mm (112-in.) widestrip or shape to suit at deck edges shall be fastened with asingle row of screws, spacing between screws not to exceed127 mm (5 in.) center

16、-to-center and located to clear deck platescrews. (See Fig. 7.)3.6 Exposed Areas Treated with Epoxy:3.6.1 Before the epoxy is applied, the surface to be coveredshould be (a) cleaned with a solvent, and (b) further treated inaccordance with Steel Structural Painting Council SP-11.3.6.2 Epoxy resin sh

17、all be applied to the exposed vertical lipof deck edges on stanchions, to approximately 305 mm (12 in.)above deck, after all other deck covering work has beenFIG. 3 Expanded View of Deck Covering at Stanchion (TYP)NOTE25.4 mm=1in.FIG. 4 Section “A-A” (See Fig. 3)FIG. 5 Expanded View of One Portable

18、Plate (TYP)NOTE25.4 mm=1in.FIG. 6 Section “B-B” (See Fig. 5)NOTE25.4 mm=1in.FIG. 7 Section “C-C” (See Fig. 5)F 13312completed. Application of epoxy shall be by brush to approxi-mately 1.5-mm (116-in.) thickness, and in accordance with TestMethod D 2393. (For location of epoxy to be applied, see Fig.

19、3 and Fig. 4.)4. Keywords4.1 deck covering; electrical space; electronic space; insu-lated deck covering; marine technology; portable deck plate;ship; vinyl deck coveringASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin

20、 this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and mus

21、t be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the

22、responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 13313