ASTM F1345-2010 Standard Specification for Zinc-5 % Aluminum-Mischmetal Alloy-Coated Steel Chain-Link Fence Fabric.pdf

1、Designation: F1345 10Standard Specification forZinc-5 % Aluminum-Mischmetal Alloy-Coated Steel Chain-Link Fence Fabric1This standard is issued under the fixed designation F1345; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the y

2、ear of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers zinc-5 % aluminum-mischmetal (Zn-5A1-MM) alloy-coated steel chain-link fencefabric, Z

3、n-5A1-MM alloy-coated, before weaving.1.2 The values stated in inch-pound units are to be regardedas the standard.2. Referenced Documents2.1 ASTM Standards:2A90/A90M Test Method for Weight Mass of Coating onIron and Steel Articles with Zinc or Zinc-Alloy CoatingsA491 Specification for Aluminum-Coate

4、d Steel Chain-LinkFence FabricA700 Practices for Packaging, Marking, and Loading Meth-ods for Steel Products for ShipmentA817 Specification for Metallic-Coated Steel Wire forChain-Link Fence Fabric and Marcelled Tension Wire2.2 Federal Standard:Fed. Std. No. 123 Marking for Shipment, Civil Agencies3

5、2.3 Military Standards:MIL-STD-129 Marking for Shipment and Storage3MIL-STD-163 Steel Mill Products, Preparation for Ship-ment and Storage33. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 chain link fence fabrica fencing material made fromsteel wire helically wound and interwov

6、en in such a manner asto provide a continuous mesh without knots or ties except inthe form of knuckling, or of twisting the ends of the wires toform the selvage of the fabric.3.1.2 diamond countthe number of diamond openingsfrom one edge of the fabric to the other. The diamond count ofa given fabric

7、 shall begin at the first completed diamond at oneedge and continue to the unfinished half or full opening at theother edge.3.1.3 knucklinga term used to describe the type of selvageobtained by interlocking adjacent pairs of wire ends and thenbending the wire ends back into a loop. The loop shall be

8、closed or nearly closed to a measurement less than the diameterof the wire.3.1.4 twistinga term used to describe the type of selvageobtained by twisting adjacent pairs of wire ends together in aclose helix of 112 machine turns, which is equivalent to threefull twists, and cutting the wire ends at an

9、 angle. The wire endsbeyond the twist shall be at least14 in. (6.4 mm) long. Thistype of selvage is not used on fabric with a mesh size of lessthan 2 in. (50.8 mm).4. Ordering Information4.1 Orders for chain-link fence fabric purchased to thisspecification shall include the following information:4.1

10、.1 Quantity (Section 13),4.1.2 Size of mesh (Section 7),4.1.3 Size of wire (Section 8),4.1.4 Height of fabric (Section 9),4.1.5 Diamond count, if specified (Section 6),4.1.6 Type of selvage (Section 10),4.1.7 Certification if required (Section 16),4.1.8 Class of Coating (Section 11), and4.1.9 ASTM d

11、esignation and year of issue.4.2 All rolls of fencing accepted by the purchaser shall bebilled on the basis of the original footage of the rolls beforesampling, unless changed by contractual arrangement.NOTE 1A typical ordering description is as follows: 25 rolls, 50 fteach, chain-link fence fabric,

12、 Zn-5A1-MM alloy-coated, 2 in. mesh, 0.148in. wire, 60 in. high, knuckled both selvages, class 2 coating toSpecification F1345.1This specification is under the jurisdiction of ASTM Committee F14 on Fencesand is the direct responsibility of Subcommittee F14.40 on Chain Link Fence andWire Accessories.

13、Current edition approved July 1, 2010. Published August 2010. Originallyapproved in 1991. Last previous edition approved in 2008 as F1345 - 96(2008).DOI: 10.1520/F1345-10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Ann

14、ual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/www.dodssp.daps.mil.1Copyright ASTM International, 100 B

15、arr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5. Materials5.1 The wire from which the fabric is woven shall conformto all requirements of Specification A817 for Type III coating,in the class of coating specified (Class 1 or Class 2).6. Weave6.1 The wire shall be wove

16、n throughout in the form ofapproximately uniform square mesh, having parallel sides andhorizontal and vertical diagonals of approximately uniformdimensions. The top and bottom of the fabric shall be knuckledor twisted as specified in Section 10.6.2 Typical diamond count for each standard height issh

17、own in Table 1. Other diamond counts are permissibleprovided that they are consistent within a lot. The purchaserhas the option to specify the diamond count (4.1.5).7. Size of Mesh7.1 The size of mesh shall be as indicated in Table 2.7.2 The permissible variation from the specified size ofmesh shall

18、 be 618 in. (63.2 mm) for all mesh sizes except 1in., and 6116 in. (61.6 mm) for 1 in. mesh size.7.3 The size of mesh shall be determined by measuring theminimum clear distance between the wires forming the parallelsides of the mesh and determined as the average of tworeadings taken at right angles

19、to each other.8. Size of Wire8.1 Chain-link fabric shall be fabricated from wire diam-eters as listed in Specification A817, with a permissiblevariation from the specified diameter of the coated wire of60.005 in. (60.13 mm).9. Height of Fabric9.1 Chain-link fabric shall be furnished in the standardh

20、eights shown in Table 2. The height of fabric shall be theoverall dimension from ends of twists or knuckles. Thepermissible variation from the specified height shall be 61 in.(625 mm) for standard selvage.10. Selvage10.1 Unless otherwise specified by the purchaser, fabricswith 2- or 218-in. (50- or

21、54-mm) mesh, in heights 60 in. (1520mm) and under shall be knuckled at both selvages. Fabric 72in. (1830 mm) high and over shall be knuckled at one selvageand twisted at the other.10.2 The selvages of fabrics with meshes of less than 2 in.(50 mm) shall be knuckled.NOTE 2Caution: Twisted selvages for

22、 fence fabric under 72 in. (1830mm) in height are not recommended because of consumer safety consid-erations.11. Weight of Coating11.1 The weight of Zn-5A1-MM alloy coating on the fabricmay be ordered in two coating weight classes as follows, inaccordance with Specification A817.11.1.1 Class 1The we

23、ight of Zn-5A1-MM alloy coatingshall not be less than 0.6 oz/ft2(183 g/m2) of uncoated wiresurface.11.1.2 Class 2The weight of Zn-5A1-MM alloy coatingshall not be less than 1.0 oz/ft2(305 g/m2) of uncoated wiresurface.11.2 The weight of coating shall be determined in accor-dance with Test Method A90

24、/A90M.12. Workmanship12.1 Chain-link fence fabric shall be produced by methodsrecognized as good commercial practices. The zinc-5 %aluminium-mishcmetal before-weaving fabric shall be wovenusing proven industry procedures to ensure a smooth consistentsurface without penetrating to the substrate, exce

25、pt at theselvage cut ends, see Note 3.12.2 Excessive roughness, blisters, and flaking shall benoted. These and other defects, if present to any considerableextent, shall provide a basis for rejection.NOTE 3Rust formations on the cut ends of the wire at the fabricselvages are inherent characteristics

26、 of this material and do not warrantrejection of the fabric.TABLE 1 Typical Diamond CountANominal Di-ameterCoatedWire, in.Size ofMesh, in.Height of Fence Fabric, in.36 42 48 60 72 84 96 108 120 1440.192 2 1012 1212 1312 1712 2012 2412 2712 3112 3412 412 10.148 2 1012 1212 1312 1712 2012 2412 2712 31

27、12 3412 41120.1481 02327333945536167790.120 2 1012 1212 1412 1712 2012 24120.1200.1200.11313412182091223111227131233161239191245311253351261391267471279ASee Appendix X1 for SI equivalents.TABLE 2 Sizes of Wire and MeshASpecifiedDiameterofCoatedWire, in.Size,CoatedWireGageSize ofMesh, in.Height of Fe

28、nce Fabric, in.0.192 6 2 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.148 9 2 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.148 9 1 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.120 11 2 36,42,48,60,72,84 .0.120 11 134 96,108, 120, 1440.120 11 1 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.113 112 1218 36,42,

29、48,60,72 ASee Appendix X1 for SI equivalents.F1345 10213. Standard Length of Rolls13.1 The standard length of roll shall be 50 ft (15.24 m) 61 % except as otherwise agreed upon at the time of purchase.13.2 The length of roll shall be determined by unrolling aroll of fabric on a flat surface and exer

30、ting tension byappropriate means to remove all slack. The tension appliedshall not reduce the actual height of the fabric by more than116in./ft (5.3 mm/m) of height or by more than12 in. (12.7 mm),whichever is less.14. Sampling and Number of Tests14.1 One roll from every 50 rolls or fraction thereof

31、 in a lotshall be taken at random as a sample for test purposes. In nocase shall less than two samples be tested, except when the lotis less than 10 rolls, only one roll shall be selected for thesample.14.2 Sample rolls selected shall be inspected for weave(Section 6), size of mesh (Section 7), diam

32、ond count (6.2), wiresize (Section 8), height of fabric (Section 9), selvage (Section10) and length (Section 13).14.3 If any specimen tested fails to meet the requirements ofthis specification, the roll represented by the specimen shall berejected and two additional rolls shall be inspected, both of

33、which shall meet the requirements in every respect; otherwise,the lot represented by the samples may be rejected.15. Inspection15.1 Unless otherwise specified in the purchase order orcontract, the manufacturer is responsible for the performanceof all inspection and test requirements specified in thi

34、s speci-fication. Except as otherwise specified in the purchase order orcontract, the manufacturer may use his own or any othersuitable facilities for the performance of the inspection and testrequirements unless disapproved by the purchaser at the timethe order is placed. The purchaser shall have t

35、he right toperform any of the inspection and tests set forth in thisspecification when such inspections and tests are deemednecessary to ensure that the material conforms to prescribedrequirements.16. Certification16.1 When specified in the purchase order or contract, aproducers or suppliers certifi

36、cation shall be furnished to thepurchaser that the material was manufactured, sampled, tested,and inspected in accordance with this specification and hasbeen found to meet the requirements. When specified in thepurchase order or contract a report of the test results shall befurnished.17. Packaging,

37、Marking, and Loading17.1 Each length of chain-link fence fabric shall be tightlyrolled and firmly tied. Each roll shall carry a tag showing thetype of coating, the specified wire size, mesh size, the specifiedlength and height of fabric in the roll, Specification A491, andthe name or mark of the man

38、ufacturer.17.2 Unless otherwise specified, packaging, marking andloading for shipment shall be in accordance with recommendedPractices A700.17.3 When specified in the contract or order, and for directprocurement by or direct shipment to the U.S. government,when Level A is specified, preservation, pa

39、ckaging, and pack-ing shall be in accordance with Level A requirements ofMIL-STD-163.17.4 When specified in the contract or order, and for directprocurement by or direct shipment to the U.S. government,marking for shipment, in addition to the requirements specifiedin the contract or order, shall be

40、in accordance with MIL-STD-129 for U.S. military agencies and in accordance with Fed. Std.No. 123 for civil agencies.APPENDIX(Nonmandatory Information)X1. APPROXIMATE SI EQUIVALENTSTABLE X1.1 Approximate SI Equivalents for Tables 1 and 2Sizes of Wire and Mesh Height of Fence Fabricin. mm in. mm0.192

41、 4.88 36 9100.148 3.76 42 10700.120 3.05 48 12200.113 2.87 60 15201 25 72 1830134 44 84 21302 50 96 2440218 54 108 2740120 3050144 3660F1345 103ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of t

42、his standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five y

43、ears andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical comm

44、ittee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19

45、428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F1345 104