1、Designation: F1450 12aStandard Test Methods forHollow Metal Swinging Door Assemblies for Detention andCorrectional Facilities1This standard is issued under the fixed designation F1450; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision
2、, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 These test methods cover requirements for mechanicaltests, simulated service test, and testing equipment
3、 for deter-mining the performance characteristics of swinging detentionhollow metal door assemblies of various styles and types ofconstruction for use in wall openings designed to incarcerateinmates in detention/correctional institutions.1.2 These test methods test the capability of a swinging doora
4、ssembly to prevent, delay, and frustrate escape, to limit orcontrol access to unauthorized or secure areas, and to resistcommon types of vandalism.1.3 These test methods apply primarily to detention doorassemblies to and from secure areas generally found insidedetention/correctional facilities, such
5、 as: day rooms, controlrooms, cells, and sally ports.1.4 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is th
6、eresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2F1577 Test Methods for Detention Locks for SwingingDoorsF1592 Test Methods for Detenti
7、on Hollow Metal VisionSystemsF1643 Test Methods for Detention Sliding Door LockingDevice AssemblyF1758 Test Methods for Detention Hinges Used onDetention-Grade Swinging DoorsF1915 Test Methods for Glazing for Detention Facilities2.2 ANSI/NAAMM/HMMA Standard:3ANSI/NAAMM/HMMA 863 Guide Specifications
8、for De-tention Security Hollow Metal Doors and Frames2.3 NFPA Standard:4252 Methods of Fire Tests of Door Assemblies2.4 UL Standards:5UL-10 (B) Fire Tests of Door AssembliesUL-10 (C) Fire Tests of Door AssembliesUL-437 Standard for Key LocksUL-752 Bullet Resisting EquipmentUL-1034 Standard for Burgl
9、ary Resistant Electric LockingMechanisms3. Terminology3.1 Definitions:3.1.1 boltmetal bar which, when actuated, is projected (orthrown) either horizontally or vertically into a retaining mem-ber, such as a strike plate, to prevent a door from moving oropening.3.1.2 bolt projection (or bolt throw)dis
10、tance from theedge of the door or frame, at the bolt center line, to the farthestpoint on the bolt in the projected position.3.1.3 componenta subassembly, as distinguished from apart, that combines with other components to make up a totaldoor assembly.3.1.3.1 DiscussionThe prime components of a door
11、 as-sembly include the following: door, lock, hinges, wall, anddoor frame (includes hinge jamb, strike jamb, and header).1These test methods are under the jurisdiction of ASTM Committee F33 onDetention and Correctional Facilities and are the direct responsibility of Subcom-mittee F33.02 on Physical
12、Barriers.Current edition approved June 1, 2012. Published July 2012. Originally approvedin 1992. Last previous edition approved in 2012 as F1450 12. DOI: 10.1520/F1450-12A.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For An
13、nual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.4Available from National Fire Protection Association (NFPA), 1
14、 BatterymarchPark, Quincy, MA 02169-7471, http:/www.nfpa.org.5Available from Underwriters Laboratories (UL), 333 Pfingsten Rd., North-brook, IL 60062-2096, http:/.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.1.4 detention securi
15、tyassurance of the restriction ofmobility of inmates to designated areas within a correctional ordetention facility.3.1.5 door assemblyunit composed of a group of parts orcomponents that make up an opening barrier for a passagewaythrough a wall.3.1.5.1 DiscussionFor the purpose of these test methods
16、,a door assembly consists of the following parts: door; hinges;locking device or devices; operation contacts (such as handles,knobs, or flush pulls); security glazing and glazing molding;miscellaneous hardware and closers; the frame, including thehead and jambs plus anchorage devices to the surround
17、ingwall; and a portion of the surrounding wall extending 32 in.(81.3 cm) from each side of the jambs and 16 in. (40.65 cm)above the head.3.1.6 forcible egressability to pass a 5 3 8 3 8 in. (127mm 3 203 mm 3 203 mm) rigid rectangular box through anopening in the test sample created by destructive te
18、stingprocedures using no more than 10 lbf (44.5 N).3.1.7 frameassembly of members surrounding and sup-porting a door or doors.3.1.8 hinged doordoor equipped with hinges that permit itto swing about the vertical hinge axis, either right-hand,left-hand, right-hand reverse bevel, or left-hand reverse b
19、evel,depending upon hardware configuration.3.1.9 hollow metalterm used in reference to such items asdoors, frames, partitions, enclosures, and other items that arefabricated from metal sheet, typically cold-rolled or hot-rolledpickled-and-oiled carbon steel.3.1.9.1 DiscussionThese products are inter
20、nally rein-forced but hollow, hence the term hollow metal. Typically, thevoids in doors and partitions are filled with insulation. Wheninstalled in masonry walls, the voids in frame jambs, headers,and mullions may be grouted or left hollow.3.1.10 manufacturerparty responsible for the fabricationof t
21、he test samples.3.1.11 panelfor the purposes of these test methods, thepanel is a steel plate at least 0.375 in. (9.5 mm), installed inorder to transfer impact energy to the glazing stops and theassembly.3.1.12 performance characteristicresponse of the doorassembly in any one of the tests described
22、herein.3.1.13 test completionconduct of one test sequence foreach of the door assemblies.3.1.14 testing laboratoryindependent materials testinglaboratory not associated with the manufacturer.4. Significance and Use4.1 A major concern for prison administrative officials issecurity barriers used in de
23、tention/correctional facilities. Thesetest methods are designed to aid in identifying levels ofphysical security for swinging detention hollow metal doorassemblies.4.2 The construction and size of test doors and all hardwarecomponents are representative of the application under inves-tigation, and a
24、re the same construction and size throughout allof the tests.4.3 These test methods are not intended to provide ameasure of resistance for a door assembly subjected to attackby corrosive agents, by high-powered rifles, explosives, saw-ing, or other such methods. These test methods are intended toeva
25、luate the resistance of a door assembly to violent attacksusing battering devices, such as benches, bunks, or tables; byhandguns up to and including .44 magnum, UL-752 Level 3;by prying devices; by devices used to deform the door andrender it inoperable; and by fires started by using mattresses,book
26、s, and other flammable materials.4.4 The primary purpose or result of these test methods is toapproximate the levels of abuse to which door assemblies arepotentially subjected in the field. The desired result of its use isto help provide insurance of protection to the public, to facilityadministrati
27、ve personnel, and to the inmates themselves.4.5 It is recommended that detention/correctional facilityadministration provide adequate training, supervision, andpreventative maintenance programs to enable door assembliesto function as intended throughout the expected service life.5. Sampling5.1 Sampl
28、e door and frame assemblies shall be constructedin accordance with 6.1.5.2 The manufacturer shall permanently mark the testsamples and retain them at the manufacturing facility for futurereference for a period of at least one year from test date.Instead of test samples, the manufacturer has potentia
29、l tocontract with the testing laboratory to provide a certifiedprocedure for the construction of tested assemblies with factoryfollow-up service as an option (see 8.2).5.3 Test reports shall include complete details of the testassemblies, details, photographs, or a combination thereof, ofthe testing
30、 apparatus, and installation instructions includingtemplates for all items of hardware (see Section 9).5.4 In the event of failure in one or more of the performancetests, the manufacturer shall provide another complete testsample including door, frame, and hardware assembly alongwith test wall where
31、 applicable. If the test is performed only onthe door, as in the door rack test (7.4), only the door need beprovided for retesting.6. Specimen Preparation6.1 Construction:6.1.1 A total of four (4) doors, for each impact, static load,and rack test, shall be constructed as described in 6.1.2 and6.1.3.
32、 Two of the doors shall be constructed in accordance withthe door elevation described in section 6.1.2. Two of the doorsshall be constructed in accordance with the door elevationdescribed in section 6.1.3. A fifth door for rack testing onlyshall be constructed and tested in accordance with section6.
33、1.4.6.1.2 The first door elevation (Door Elevation #1) is de-scribed as a flush door with a single narrow vision light.6.1.2.1 The construction and size of the test door assembliesconsisting of single doors, frames, and all hardware compo-nents shall be representative of the application under invest
34、i-gation within the following guidelines:6.1.2.2 The same construction and size of test doors andassemblies shall apply to all tests.F1450 12a26.1.2.3 Each test door shall be equipped with a 100in.2(64 516 mm2) vision light with impact panel installed, 4 by25 in. (102 by 635 mm) clear opening positi
35、oned generally asshown in Fig. 1.6.1.2.4 The first door shall swing on three full mortised butthinges and shall be locked using a door-mounted, pocket-typedetention security lock with bolt size not to exceed 2 in. (51mm) high by34 in. (19 mm) wide and latch bolt engagementnot to exceed78 in. (22.3 m
36、m).6.1.2.5 The second door shall swing on three full mortisedbutt hinges and shall be locked using a jamb-mounted securitylock with bolt size not to exceed 2 in. (51 mm) high by34 in.(19 mm) wide and latch bolt engagement not to exceed78 in.(22.3 mm).6.1.2.6 Required results indicated in Table 1 are
37、 based upona nominal door size of 3 by 7 ft (914 by 2133 mm).6.1.3 The second door elevation (Door Elevation #2) isdescribed as a vision light door with two large vision lights asshown in Fig. 2.6.1.3.1 The construction and size of the test door assembliesconsisting of single doors, frames, and all
38、hardware compo-nents shall be representative of the application under investi-gation within the following guidelines:6.1.3.2 The same construction and size of test doors andassemblies shall apply to all tests.6.1.3.3 Each test door shall be equipped with two visionlights centered horizontally and lo
39、cated generally as shown inFig. 2. The top vision light shall be a 532 in.2(343 225 mm2)vision light with impact panel installed, 19 by 28 in. (483 by711 mm) clear opening positioned generally as shown in Fig.2. The bottom vision light shall be a 342 in.2(220 645 mm2)vision light with impact panel i
40、nstalled, 19 by 18 in. (483 byFIG. 1 Test Assembly Door Elevation #1 Location of Strike Points Described in Table 1F1450 12a3457 mm) clear opening positioned generally as shown in Fig.2. The impact plate in the top vision panel shall be installedusing face mount “Z” type or “P” type removable surfac
41、eapplied glazing stops as shown in Fig. 2 Section B-B or SectionC-C. The impact plate in the bottom vision light shall beinstalled using pressed angle type removable glazing stops asshown in Fig. 2 Section A-A.6.1.3.4 The first door shall swing on three full mortised butthinges and shall be locked u
42、sing a door-mounted, pocket-typedetention security lock with bolt size not to exceed 2 in. (51mm) high by34 in. (19 mm) wide and latch bolt engagementnot to exceed78 in. (22.3 mm).6.1.3.5 The second door shall swing on three full mortisedbutt hinges and shall be locked using a jamb-mounted securityl
43、ock with bolt size not to exceed 2 in. (51 mm) high by34 in.(19 mm) wide and latch bolt engagement not to exceed78 in.(22.3 mm).6.1.3.6 Required results indicated in Table 2 are based upona nominal door size of 3 by 7 ft (914 by 2133 mm).6.1.4 The third door elevation, Elevation #3 (Fig. 3), isdescr
44、ibed as a 12 ga., 0.093 in. (2.3 mm) vision light door withtwo large vision lights as shown in Fig. 2, with the addition ofan “Edge Cut” food pass / cuff port, opening size 5 in. (127mm) high 3 14.25 in. (362 mm) long, located 36.5 in. (927mm) from the bottom of the door to the centerline of theopen
45、ing.6.2 Impact Test Fixture:6.2.1 The door assembly support fixture and wall shallsimulate the rigidity normally provided to a door assembly ina building by the ceiling, floor, and walls. Fig. 4 illustrates anacceptance fixture.6.2.2 The fixture is designed to accommodate two testsamples; however, i
46、t is permissible to construct a test fixturethat accommodates one sample only, if the manufacturer sochooses.6.2.3 Description of the Test WallThe door assembly shallbe mounted in a vertical wall section constructed suitably toretain the sample(s) throughout the testing procedure. Typicalwall detail
47、s shown in Figs. 4-7 describe an acceptance wall.The wall specification shall be included as part of the testreport.6.3 Mounting for Impact Testing:6.3.1 Mount the swinging doors so as to open away from theworking area. Position the impact test ram opposite the doorside of the assembly so that the d
48、oor opens away from the ram.6.3.2 Prepare doors and door jambs for the installation oflocksets and hinges in conformance with the hardware manu-facturers instructions and templates. Follow the hollow metaldoor assembly manufacturers instructions for fastening thejamb to the support fixture described
49、 in 7.2.6.3.3 Install components such as test doors, door frames,hinges, and hardware in the component test fixture described in7.2. Provide clearances on the lock side, hinge side, and top ofthe door18 in. 6116 in. (3.2 6 1.5 mm) maximum. Clearanceat the threshold is not considered critical in these tests.7. Procedures7.1 Bullet Penetration:7.1.1 When specified by the contract documents of adetention/correctional facility project, test door assemblies forbullet penetration in accordance with UL-752.7.1.2 Testing of the door, frame, hardw
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1