ASTM F1516-2003 Standard Practice for Sealing Seams of Resilient Flooring Products by the Heat Weld Method (when Recommended)《用热焊接法(推荐的)密封弹性地板产品接缝的标准实施规范》.pdf

1、Designation: F 1516 03Standard Practice forSealing Seams of Resilient Flooring Products by the HeatWeld Method (when Recommended)1This standard is issued under the fixed designation F 1516; the number immediately following the designation indicates the year oforiginal adoption or, in the case of rev

2、ision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers the instructions and precautions tobe observed to ensure satisfactory perform

3、ance of seams inresilient flooring sealed by the heat weld method.1.2 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the app

4、lica-bility of regulatory limitations prior to use. See precautioninformation in 6.1.2. Referenced Documents2.1 ASTM Standards:F 141 Terminology Relating to Resilient Floor Coverings23. Terminology3.1 For definitions of terms used in this practice refer toTerminology F 141.4. Significance and Use4.1

5、 Seams in some resilient flooring are heat sealed toprevent openings from forming between cut edges and toprevent penetrations of dirt, liquids, etc., into the seams.Decorative appearances may also be achieved using contrast-ing heat weld thread (rod).5. Instructions5.1 Flooring shall be installed i

6、n accordance with themanufacturers instructions.5.2 Particular attention shall be paid to proper cutting ofseams and tightness of cut seams. Specified tightness of seamsto be heat sealed (welded) will vary depending on the flooringproduct and type of tools used to perform the heat weld.5.3 Prior to

7、heat welding, seams shall be routed to a depthspecified by the manufacturer. Routing can be accomplishedwith electric or hand routing tools as specified by the manu-facturer. Follow flooring manufacturers instructions for spe-cific details.5.4 Routing and heat welding of seams normally are per-forme

8、d the day after flooring is adhered (installed) to allowadhesive to dry. Some tile products are routed at the factory,and on site routing is not required. The process involves themelting of thread (rod) into the gap of a routed seam. Specialelectric hot air tools with variable temperature settings a

9、rerequired. Because temperature settings will vary depending onthe length of extension cord, room and underfloor temperature,floor covering material, and welding rod composition, a triallength shall be performed and tested after cooling to determineif the bond and appearance of the weld thread to th

10、e seamedges is satisfactory. Weld threads are available in variouscolors to match the color of the flooring. Accent thread colorsare also available. Use weld thread (rod) as recommended bythe manufacturer of the flooring.5.5 Approximately one-half of the weld thread thicknesswill adhere to the seam.

11、 The excess will be trimmed off flushwith the surface of the flooring when cooled. Trimming ofexcess weld thread is accomplished in one step for rubberproducts and in two steps for vinyl and linoleum products.Generally, it is recommended to let welded seams cool beforetrimming. There are a few excep

12、tions, so follow manufactur-ers specific recommendations. Trim knives and attachmentsare available from the flooring manufacturer or various flooringinstallation tool suppliers.5.6 Some manufacturers recommend use of a final glazingwith either the heat gun or use of a chemical sealer to reducethe po

13、rosity and seal the top surface of the weld. Followmanufacturers specific recommendations.6. Precautions6.1 Use caution when handling and using tools required forheat welding seams. Hot air guns can cause severe burns.Routing tools and trim knives are very sharp. Be sure electric1This practice is un

14、der the jurisdiction of ASTM Committee F06 on ResilientFloor Coverings and is the direct responsibility of Subcommittee F06.40 on SpecialProperties.Current edition approved Sept. 10, 2003. Published November, 2003. Originallyapproved in 1994. Last previous edition approved in 1994 as F 151694 (1999)

15、.2Annual Book of ASTM Standards, Vol 15.04.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.extension cords are in good condition and connected to aground fault receptacle.7. Keywords7.1 heat weld; installation; resilient sheet floori

16、ng; resilienttile; sealingASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infrin

17、gement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard

18、 or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views

19、 known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F1516032