1、Designation: F1665 08 (Reapproved 2018)Standard Specification forPoly(Vinyl Chloride) (PVC) and Other Conforming OrganicPolymer-Coated Steel Barbed Wire Used With Chain-LinkFence1This standard is issued under the fixed designation F1665; the number immediately following the designation indicates the
2、 year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers PVC and other conformingo
3、rganic polymer-coated steel barbed wire consisting of twopolymer-coated strands, with four-point barbs of zinc-coatedsteel or aluminum alloy wire. PVC and other organic polymercoatings hereinafter will be designated as polymer coating.1.2 Barbed wire strand wire, produced from three classes ofwire c
4、oatings, is covered as follows:1.2.1 Class 1, consisting of a polymer coating extruded overzinc-coated or aluminum-coated or zinc-5 % aluminum-mischmetal alloy-coated steel wire;1.2.2 Class 2a, consisting of a polymer coating extrudedand adhered to zinc-coated or aluminum-coated or zinc-5 %aluminum-
5、mischmetal alloy-coated steel wire; and1.2.3 Class 2b, consisting of a polymer coating fused andadhered to zinc-coated or aluminum-coated or zinc-5 %aluminum-mischmetal alloy-coated steel wire.1.3 The values stated in inch-pound units are to be regardedas the standard. The values given in parenthese
6、s are forinformation only.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organiz
7、ation TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2A90/A90M Test Method for Weight Mass of Coating onIron and Steel Articles with Zinc or Zinc-Alloy CoatingsA370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA428/A428M Test Method for We
8、ight Mass of Coating onAluminum-Coated Iron or Steel ArticlesA700 Guide for Packaging, Marking, and Loading Methodsfor Steel Products for ShipmentD1499 Practice for Filtered Open-Flame Carbon-Arc Expo-sures of PlasticsF552 Terminology Relating to Chain Link FencingF934 Specification for Standard Col
9、ors for Polymer-CoatedChain Link Fence MaterialsG152 Practice for Operating Open Flame Carbon Arc LightApparatus for Exposure of Nonmetallic MaterialsG153 Practice for Operating Enclosed Carbon Arc LightApparatus for Exposure of Nonmetallic Materials2.2 Federal Standard:3Fed. Std. No. 123 Marking fo
10、r Shipments (Civil Agencies)2.3 Military Standards:3MIL-STD-129 Marking for Shipment and StorageMIL-STD-163 Steel Mill Products, Preparation for Ship-ment and Storage3. Terminology3.1 DefinitionsFor definitions of terms such as fabric(chain-link fence), PVC, and polymer coating, see Terminol-ogy F55
11、2.4. Classification4.1 Polymer-coated steel barbed wire is supplied in a choiceof two types as follows:4.1.1 Type I (Standard), with barbs spaced on 5-in. (127-mm) centers; and4.1.2 Type II (High Security), with barbs spaced on 3-in.(76-mm) centers.1This specification is under the jurisdiction of AS
12、TM Committee F14 on Fencesand is the direct responsibility of Subcommittee F14.40 on Chain Link Fence andWire Accessories.Current edition approved March 1, 2018. Published March 2018. Originallyapproved in 1995. Last previous edition approved in 2013 as F166508(2013). DOI:10.1520/F1665-08R18.2For re
13、ferenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, DODSSP, Bldg.
14、4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/www.dodssp.daps.mil.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on
15、 standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.15. Ordering Information5.1 Orders for barbed wire purchased in accordance withthis
16、specification shall include the following information:5.1.1 Quantity (expressed in number of spools);5.1.2 Length of spools (1320 or 1000 ft (402 or 305 m); see9.4);5.1.3 Class of a polymer coating to be applied to metallic-coated steel strand wire;5.1.4 Color of coating;5.1.5 Type of barbs (galvani
17、zed steel or aluminum alloy; see6.3);5.1.6 Type of barbed wire (Type I or II; see 4.1.1 and 4.1.2);5.1.7 Selection of type of metallic coating on the steel strandwire substrate, which shall be the choice of the producer unlessotherwise specified;5.1.8 Packaging requirements;5.1.9 ASTM designation an
18、d year of issue; and5.1.10 Certification, if required;5.2 Any tests required other than those covered specificallyin this specification must be stipulated by the purchaser in theorder or contract.5.3 All spools of barbed wire accepted by the purchasershall be billed on the basis of the number and or
19、iginal length.NOTE 1A typical ordering description is as follows: 20 spoolspolymer-coated steel barbed wire, 1000-ft (305-m) spools, Class 2bcoating, olive green color, aluminum alloy barbs, Type II (high security),on pallets, certified this specification.6. Materials6.1 Base MetalThe base metal sha
20、ll be steel of suchquality and purity that, when drawn to the size of wirespecified, it shall be of uniform quality and have properties andcharacteristics as prescribed in this specification.6.2 Wire used for the manufacture of strand wire shall meetthe requirements of this specification. The polyme
21、r coatingshall be formulated and produced properly to conform to therequirements of this specification.6.3 Materials for Barbs:6.3.1 Zinc-Coated Steel Wire, if used for the barbs, shall be14 gage, 0.080 in. (2.03 mm), having a Class 3 zinc coating,minimum 0.70 oz/ft (215 g/m) when tested in accordan
22、ce withTest Method A90/A90M.6.3.2 Aluminum Alloy Wire, if used for the barbs, shall be 14gage, 0.080 in. (2.03 mm), Alloy 5000-H38, 6061-T94, orequal, as agreed upon between the manufacturer and thepurchaser at the time of purchase.6.3.3 The choice of either zinc-coated steel wire or alumi-num alloy
23、 wire for the barbs shall be that of the manufacturer,unless otherwise specified by the purchaser.7. Manufacture7.1 Class 1 polymer-coated wire shall have the coatingextruded onto the strand wire that conforms to the requirementsas given in Table 1.7.2 Class 2a polymer-coated wire shall have the coa
24、tingextruded and adhered to the strand wire that conforms to therequirements as given in Table 1.7.3 Class 2b polymer-coated wire shall have the coatingfused and adhered to the strand wire that conforms to therequirements as given in Table 1.8. Size and Construction8.1 All barbed wire furnished in a
25、ccordance with thisspecification shall be fabricated from two strands of 14 gage,0.080-in. (2.03-mm) metallic-coated core, polymer-coatedsteel wire, with four-point barbs of 14 gage, 0.080-in. zinc-coated steel or aluminum alloy wire.9. Size and Permissible Variations9.1 Line WireThe permissible var
26、iation from the nominaldiameter of the wire shall be 60.004 in. (0.10 mm).9.2 BarbsDue to the mechanics of the manufacture whenforming the barbs, a certain amount of out-of-roundness can beexpected, and this precludes barbs from being subjected tochecks for other than nominal diameter and length. Me
27、asuredfrom the center of the two strand wires, the barb length shall be38 in. (9.5 mm), minimum.9.3 Spacing of BarbsBarbs shall be spaced as indicated in4.1.1 or 4.1.2. The individual barb spacing shall be measuredfrom the edge of one barb at the strand to the correspondingedge of the adjacent barb.
28、 Cumulative spacing is established bycounting the total number of barbs in a 25-ft (7.6-m) length ofbarbed wire. Barbs are subject to relocation during fabricationand handling; therefore, a rigid interpretation of the spacingrequirement may lead to undue rejections. Any sample with93.5 % of the indi
29、vidual barb spacings conforming to thespecified spacing (634 in. (19 mm) and containing a minimumof 55 barbs (5-in. (127-mm) spacing) or a minimum of 86barbs (3-in. (76-mm) spacing) in 25 ft shall be consideredacceptable.9.4 The length of barbed wire in each spool shall be 80 rods(402 m). This is eq
30、uivalent to one-quarter mile, or 1320 ft. Atthe option of the manufacturer, 1000-ft (305-m) spools may beoffered.10. Joints and Workmanship10.1 Splicing of individual wires by means of a wrap jointor an electric butt weld is permitted. Not more than threesplices or joints shall exist in any spool of
31、 barbed wire. Suchsplices or joints shall be made in a workmanlike manner.10.2 The strands shall be twisted with a uniform length oflay. The direction of twisting may be either right or left hand.Alternate left and right hand twisting is not permitted.10.3 The barbs shall be sharp, well-formed, wrap
32、ped tightly,and spaced in accordance with 9.3.TABLE 1 Weight of Strand Wire Metallic CoatingsSpecified CoreDiameter of StrandWire, in. (mm)Minimum Weight ofZinc Coating, oz/ft(g/m)Minimum Weight ofAluminum Coating,oz/ft2(g m2)Minimum Weight ofZinc-5 %Aluminum-MischmetalCoating, oz/ft (g/m)0.080 (2.0
33、3) 0.25 (75) 0.20 (61) 0.25 (75)F1665 08 (2018)211. Weight of Metallic Coating11.1 The minimum weight of zinc coating for the galva-nized barbs shall be 0.70 oz/ft (215 g/m). The minimum weightof the strand wire metallic coating shall conform to Table 1when tested in accordance with Test Method A90/
34、A90M orTest Method A428/A428M, as applicable.12. Breaking Strength12.1 The minimum breaking strength of the stranded barbedwire shall be 760 lbf (3380 N) when tested in accordance withTest Methods and Definitions A370. This breaking strengthvalue reflects that of both strand wires together as one un
35、it.13. Properties of Polymer-Coated Barbed Wire13.1 The polymer-coated barbed wire shall have a demon-strated ability to conform to the following requirements:13.2 Adhesion Tests:13.2.1 Class 2a shall conform to the requirements of 13.2.2.Class 2b shall conform to the requirements of 13.2.3.13.2.2 T
36、hree specimens from each lot shall be tested.Measure a distance of34 in. (19 mm) from the end of thespecimen. With a regular hand grip wire stripper, exert maxi-mum hand pull parallel to the axis of the wire. Attempt toremove the measured portion of the polymer sleeve from thecore wire. The lot shal
37、l be acceptable if the polymer sleeve isnot capable of being removed from the core wire on all threesamples.13.2.3 Three specimens from each lot shall be tested. Maketwo cuts parallel to the axis of the wire through the coating,approximately116 in. (1.6 mm) apart, at least12 in. (12.7 mm)long. With
38、a knife, peel back a section of the coating between18 and14 in. (3.2 and 6.4 mm) long to produce a tab. Attemptto remove the116-in. (1.6 mm) strip of coating by pulling thetab. The lot shall be acceptable if the coating breaks rather thanseparates from the core wire on all three specimens.13.3 Accel
39、erated AgingThe polymer-coated wire shallwithstand exposure for 1000 h without failure at a black paneltemperature of 145F (63C) when tested in accordance withPractice D1499. The appropriate apparatus described in Prac-tices G152 or G153 shall be used for the test. The product shallbe construed to h
40、ave failed the test if one of the followingoccurs:13.3.1 Shrinkage of the polymer coating is greater than116in./ft (1.6 mm/305 mm) of wire.13.3.2 There shall be no significant change in color or glossof the polymer surface as determined by visual inspection.13.4 ColorUnless otherwise stipulated by t
41、he purchaser,the color of the polymer shall be in accordance with thestandard colors contained in Specification F934: green, olivegreen, brown, and black.14. Thickness of Polymer Coating14.1 The thickness of the polymer coating shall be inaccordance with Table 2.14.2 The thickness of the polymer coa
42、ting shall be deter-mined on an individual piece of wire. This specimen may beany length of wire over 12 in. (305 mm).14.3 For Class 1 and Class 2a material, strip the polymercoating mechanically from the wire and measure the minimumand maximum thickness of the polymer coating with a suitablemicrome
43、ter.14.4 For Class 2b material, strip the polymer coating bychemical means and determine the diameter of the bare wire.Scrape the coating from one side of the wire and measure thereduced diameter with a micrometer. The thickness of thecoating at this point is the difference between the measurementth
44、us obtained and the measured diameter of the bare wire. In asimilar manner, determine the thickness of the coating at rightangles to the first determination.14.5 Take care not to remove any of the metallic surfacewhen removing polymer coating by scraping.15. Sampling15.1 For the purpose of the tests
45、, one spool from every 50spools or fraction thereof in a lot shall be selected at random,or a total of seven samples, whichever is less.Alot shall consistof all of the spools of a single type of barbed wire offered fordelivery at the same time.15.2 Test SpecimensA 4-ft (1.2-m) length of barbed wires
46、hall be cut from the end of the spool for the tests prescribedin Sections 1114. Each strand wire shall be tested for itsmetallic and polymer coating. The breaking strength valueshall be determined by having the twisted strand tested as acomposite.15.3 Instead of testing wire for its coating and brea
47、kingstrength from the completed barbed wire in accordance with15.2, the manufacturer may elect to establish compliance withSections 1114by tests made on wire prior to fabrication. Ifthe manufacturer makes this election, the purchaser stillreserves the right to test wire from the completed barbed wir
48、efor compliance.15.4 For the purpose of inspection, a maximum of twospools from the lot (as described in 15.1) may be subjected toobservations for barb length and spacing, overall length, andgeneral workmanship.15.5 Instead of inspecting for length by unrolling full spoolsin accordance with 15.4, th
49、e purchaser and the manufacturermay agree on a weight per spool related to the wire size ormeasuring tools used during manufacturing. The purchaser stillreserves the right to confirm the length by actual measurement.15.6 Inspection for barb spacing is normally performed onthe outer 25-ft (7.6-m) length of a spool; this permits repack-aging of the spool. Any other selection shall be as agreed uponbetween the manufacturer and the purchaser.TABLE 2 Thickness of Polymer CoatingClass 1 andClass 2a, in. (mm)Class 2b, in. (mm)Minimum thickness at any point 0.015
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1