ASTM F1750-2011 Specification for Paintball Marker Threaded-Propellant Source Interface《彩弹球枪加螺纹推进装置接口标准规范》.pdf

1、Designation:F175005 (Reapproved 2010) Designation: F1750 11An American National StandardStandard Specification forPaintball Marker Threaded-Propellant Source Interface1This standard is issued under the fixed designation F1750; the number immediately following the designation indicates the year ofori

2、ginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the male and female threaded connect

3、ors used to interface a propellant source with a workingpressure of 10 342 kPa (1800 psig) or less to a paintball marker.1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the

4、 safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D2240 Test Method for Rubber P

5、ropertyDurometer Hardness Durometer HardnessF2272 Specification for Paintball Markers2.2 ANSI Standard:3ANSI Y14.5M1994 Dimensioning and Tolerancing2.3 CGA Standard:4CGA-320 .825-14NGO-RH-EXT (Flat Nipple)2.4 Federal Standard:5FED-STD-H28/9A 24 March 1989 Federal Standard Screw-Thread Standards for

6、Federal Services Section 9 Gas CylinderValve Outlet and Inlet Threads2.5 Military Standard:5MS28775 O-Ring Dash Sizes3. Connector Gender Assignment3.1 The female connector is that connector which is configured as part of the paintball marker conforming to SpecificationF2272.3.2 The male connector is

7、 that connector which is configured as part of the propellant source.4. Materials and Manufacture4.1 The male and female connectors shall be made from materials that are compatible with CO2, compressed air, or gaseousnitrogen. The materials and processes used to manufacture male and female connector

8、s shall result in items with mechanicalstrength sufficient to pass a 20 684-kPa (3000-psig) proof pressure check without failure or any degradation to function.4.2 The O-ring seal shall be made from an elastomer compatible with CO2, compressed air, or gaseous nitrogen. The O-ringseal shall have a ha

9、rdness that will register a Type A durometer reading of 90 6 5. The O-ring shall conform dimensionally toMS28775-015 and conform to Test Method D2240.4.3 The O-ring seal shall be installed on the male connector in the groove described by Dimensions C and K on Fig. 1.1This specification is under the

10、jurisdiction of ASTM Committee F08 on Sports Equipment and Facilities and is the direct responsibility of Subcommittee F08.24 onPaintball and Equipment.Current edition approved Feb. 1, 2010. Published May 2010. Originally approved in 1996. Last previous edition approved in 2005 as F175005. DOI:10.15

11、20/F1750-05R10.Current edition approved March 1, 2011. Published March 2011. Originally approved in 1996. Last previous edition approved in 2010 as F1750 05 (2010). DOI:10.1520/F1750-11.2For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm

12、.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036.4Available from Compressed Gas Association (CGA), 1725 Jefferson Dav

13、is Hwy., Suite 1004, Arlington, VA 22202-4102.5Available from U.S. Government Printing Office Superintendent of Documents, 732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401.1This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of

14、 what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered

15、 the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4.4 The male and female connectors shall not have any sharp edges or hanging burrs.All sharp edges will be broken R.38 MAX(R.015 MAX).5. Performance5.1The interfac

16、e is intended for use with CO5.1 The interface is intended for use with compressed air, gaseous nitrogen, or CO2compressed air or gaseous CO2, or both. .5.2 The maximum operating pressure of the interface is 10 342 kPa (1800 psig).5.3 The maximum allowable leakage at 10 342 kPa (1800 psig) is 0.1 cm

17、3/min.5.4 The male connector shall incorporate a means for propellant shutoff that shall meet the maximum leakage requirement.5.5 When the male and female connectors are joined and pressurized, together they shall meet the maximum leakagespecification.6. Physical Envelope6.1 The male connector shall

18、 conform to the physical envelope described in Fig. 1.6.2 The female connector shall conform to the physical envelope described in Fig. 2.7. Valve Core7.1 The male connector may contain, as a means of propellant shutoff, a valve core to provide for an automatic shutoff of flowat the time of disconne

19、ction. The stem of the valve core shall not protrude beyond the face of the male connector, that surfacedesignated as Datum B in Fig. 1. Full flow must be achieved when the stem of the valve core has been depressed 1.78 mm (0.070in.) from the surface designated as Datum B in Fig. 1. The stem of the

20、valve core shall be able to be depressed to a minimum depthof 2.54 mm (0.100 in.) below Datum B without being damaged. If a valve core is not used there shall not be any feature of themale connector which will interfere with the valve opening feature of the female fitting.8. Venting8.1 The female co

21、nnector shall have a provision for the self venting of residual gas pressure prior to the disconnection of thethreaded interface. Fig. 2 (Dimensions D and H) shows a recommended location and feature size for a vent hole.9. Operating Temperatures9.1 The interface shall have an operating range from 40

22、 to + 54C (40 to + 130F).Dimension SI InchesA f22.86 min f0.900 minB f18.46/17.02 f0.727/0.670C f14.66 6 0.08 f0.5776 0.003D R.25 6 0.13 R.010 6 0.005E f17.60/17.40 f0.693/0.685F 16.66 min 0.656 minG 6.35 6 0.13 0.250 6 0.005H 2.54 6 0.5 0.100 6 0.020J 1.02 6 0.13 0.040 6 0.005K 2.16 6 0.08 0.085 6

23、0.003N 0.38 6 0.13 3 45 6 3 0.015 6 0.005 3 4563M R 5.54 6 0.38 R.218 6 0.015FIG. 1 Male ConnectorF1750 11210. Flow10.1 The interface shall flow not less than 170 sL/min at 689 kPa (6 S.C.F.M. at 100 psid).10.2 The feature allowing flow through the female connector shall lie within the area designat

24、ed by minimum Dimension Min Fig. 2.10.3 The feature allowing flow through the male connector shall lie within the area designated by Dimension M in Fig. 1.11. Keywords11.1 paintball marker; propellantASTM International takes no position respecting the validity of any patent rights asserted in connec

25、tion with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsib

26、le technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful con

27、sideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100

28、Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM web

29、site(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).Dimension SI InchesA 15.75 6 0.13 0.620 6 0.005B 5.08 6 0.13 0.200 6 0.005C 1.91 6 0.13 0.075 6 0.005D 7.32 6 0.13 0.288 6 0.005E 3.18 6 0.13 0.125 6 0.005F f17.78/17.63 f0.700/0.694G 0.89 min 0.035 minH f0.79 min f0.031 minJ R.64 max R.025 maxK 9.40 min 0.370 minM R 4.78 max R.188 maxO 21.59 6 0.254 0.85 6 0.010FIG. 2 Female ConnectorF1750 113