ASTM F1935-2001(2007) Standard Test Method for Measuring the Headroom of a Backpacking or Mountaineering Tent《测量背包式或登山用帐蓬高度的标准试验方法》.pdf

1、Designation: F 1935 01 (Reapproved 2007)An American National StandardStandard Test Method forMeasuring the Headroom of a Backpacking orMountaineering Tent1This standard is issued under the fixed designation F 1935; the number immediately following the designation indicates the year oforiginal adopti

2、on or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers tents for use in the sports ofbackpacking and mou

3、ntaineering. It establishes requirementsfor the testing and marking of tents.1.2 This test method may contain test methods that do notentirely simulate real life situations. This test method isdesigned to give reproducible results in a laboratory andthereby a means for product comparison.1.3 This st

4、andard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Terminology2.1 Definiti

5、ons of Terms Specific to This Standard:2.1.1 tenta portable shelter made primarily of fabricweighing less than 3 oz/yd2, designed to be carried by theoccupants for while backpacking or mountaineering.2.1.2 usable headroomthe interior vertical measurementof a tent measured from the tent floor to the

6、high point on theceiling using a simple fixture that simulates an average usershead.3. Significance and Use3.1 This test method can be used to quantify and compareheadroom of backpacking and mountaineering tents. Themeasured headroom can be used as a manufacturing standardor a measurement that can b

7、e used by consumers to comparethe interior height of a variety of tents, or both.4. Apparatus4.1 Specifications for Headroom Measurement Fixture (seeFig. 1):4.1.1 Styrofoam ball 6 inches in diameter (mean width ofmale head = 6.1 in.).24.1.2 Tape Measure,14 in. GraduationsThe tape ismounted into the

8、bottom of the Styrofoam ball, and the first 6inches are removed from the tape. In this way, the reading willbe simple and accurate.5. Summary of Test Method5.1 The tent should be pitched on a flat surface in accor-dance with the companys supplied pitching instructions .5.2 The fixture shall be place

9、d inside the tent. The ball israised until it comes into contact with the ceiling, wall, poles,or any other obstructions inside the tent.5.3 The tape measure will now be hanging directly belowthe ball. The headroom measurement will be where themeasuring tape hits the tent floor. If the tent does not

10、 have afloor, record the measurement to the surface the tent has beenset up on.6. Conditioning6.1 Tests may be completed under ambient conditions. Incases of dispute, test samples shall be conditioned in accor-dance with 6.2.6.2 The tent samples are first erected and dried in anatmosphere with a rel

11、ative humidity of less than 10 % for aminimum period of 24 h. They are then placed in an atmo-sphere of 50 6 5 % relative humidity, 20 6 2 C for aminimum period of 72 h. Tests may then be done outside theconditioning room, but the temperature shall be 23 6 5Candthe tests shall begin within 5 min. of

12、 removal from condition-ing and be completed within 4 h.7. Sampling, Test Specimens, and Test Units7.1 The tent test specimen shall be new and in unusedcondition. When possible, it shall be selected randomly from aproduction lot of a given model of tent. It shall conform in allrespects to the manufa

13、cturers specifications for that model.1This test method is under the jurisdiction of ASTM Committee F08 on SportsEquipment and Facilities and is the direct responsibility of Subcommittee F08.22 onCamping Softgoods.Current edition approved May 1, 2007. Published August 2007. Originallyapproved in 199

14、8. Last previous edition approved in 2001 as F 1935 01.2Henry Dreyfuss Associates, The Measure of Man and Woman: Human Factorsin Design, Whitney Library of Design, 1993.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.8. Report8.1 The

15、 test report shall include the name of the tentmanufacturer, the model of tent tested, the date and location ofthe tests, the name(s) of personnel conducting the tests, if thetent is a production model or prototype, and the peak height.8.2 Markings, if included in the tent or marketing literature,sh

16、all reference this test method.9. Precision and Bias9.1 The precision of this test method is within14 in. Thebias of this test method has not yet been determined.10. Keywords10.1 backpacking; height; mountaineering; peak; tentsASTM International takes no position respecting the validity of any paten

17、t rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision a

18、t any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your commen

19、ts will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted

20、by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).FIG. 1 A Typical Fixture for Measuring HeadroomF 1935 01 (2007)2