1、Designation: F 2053 00 (Reapproved 2006)Standard Guide forDocumenting the Results of Airborne Particle PenetrationTesting of Protective Clothing Materials1This standard is issued under the fixed designation F 2053; the number immediately following the designation indicates the year oforiginal adopti
2、on or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.INTRODUCTIONWhile test methods exist to measure penetration of airborne particles thr
3、ough barrier specimens, thedata are not reported in a standard fashion. To be useful, such data should be combined withinformation that characterizes the test method employed. This information includes descriptions of testmaterials, challenge particles, test apparatus, methods used to count and meas
4、ure the particles and testparameters such as flow rate, pressure drop, humidity, and temperature. The flow rate, pressure drop,particle size, and detection limits are of particular importance when comparing data from differentsources during the selection of protective clothing. Some reports on parti
5、cle barrier testing do notinclude such specificity. This guide provides a standard format for recording important test parameterinformation and data. The standard format is intended to facilitate the use of electronic databases tostore, retrieve, and apply test results.1. Scope1.1 This guide provide
6、s a format for documenting informa-tion and performance data for a airborne particle penetrationtest.1.2 Documented data and information are grouped into fivecategories that define important aspects of each test:1.2.1 Description of material tested,1.2.2 Challenge particles,1.2.3 Test method,1.2.4 T
7、est results, and1.2.5 Source of the data.1.3 Use of this guide is facilitated by adherence to proce-dures outlined in a standard test method.1.4 The values stated in SI units are to be regarded asstandard. No other units of measurements are included in thisstandard.2. Significance and Use2.1 This gu
8、ide is intended to encourage thorough andconsistent documentation of airborne particle penetration test-ing and its results.2.2 Uniform information and performance data increase thelikelihood of selecting proper particle protective clothing bydirect comparison of one material with another.2.3 A stan
9、dard format for test information and data alsoencourages computer storage of test results for easy retrieval,comparison, and correlations.3. Data Fields3.1 The reporting format is shown in Fig. A1.1.3.2 If a particular field is not applicable to the testingperformed, insert “not applicable” in that
10、field. If a particularpiece of data has not been obtained, insert “no data” or“unknown” in the field.3.3 A description of each field of information follows:3.3.1 Description of Material TestedIdentification of thespecific protective clothing material tested to facilitate futureidentification of the
11、test materials.3.3.1.1 Material IdentificationThe manufacturers code,model number, catalog number or “brand name” whichuniquely describes the material tested.3.3.1.2 Material DescriptionA unique generic descriptionof the material composition and construction, such as thecomposition, thickness, and w
12、eight of various layers.3.3.1.3 ManufacturerThe name, postal address, e-mailaddress, and telephone number of the manufacturer. If un-known, then enter the source of the tested material.3.3.1.4 Lot Identification or Manufacture DateThe pro-duction lot/batch identification, date or code that uniquelyi
13、dentifies the material tested. If this information cannot befound, enter the earliest date that the actual test sample wasknown to exist, for example, the purchase date, the suppliersstocking data, the shipping date, date of receipt, or testing date.1This guide is under the jurisdiction of ASTM Comm
14、ittee F23 on PersonalProtective Clothing and Equipment and is the direct responsibility of CommitteeF23.30 on Chemicals.Current edition approved June 1, 2006. Published June 2006. Originallyapproved in 2000. Last previous edition approved in 2000 as F 2053 - 00.1Copyright ASTM International, 100 Bar
15、r Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.3.1.5 ThicknessThe nominal thickness, in mm, of thebarrier material and the test method by which this measurementwas made.3.3.1.6 Basis WeightThe nominal basis weight, in g/m2,of the barrier material and the test method b
16、y which thismeasurement was taken.3.3.1.7 Treatment Before TestingTreatment of the mate-rial specimen prior to testing. Examples are “new,” “laun-dered,” “flexed,” “abraded,” “after two weeks productionusage,” and “after decontamination.”Any laundering or decon-taminating procedures should be descri
17、bed or referenced. If astandard method is used to prepare or pre-treat the specimens,full reference to the method, date or version of the method, andany exceptions to the method should be specified.3.3.2 Challenge Particles:3.3.2.1 Particle CompositionA description of the compo-sition, physical size
18、, and method used to generate the challengeparticles.NOTE 1The exact identity of the challenge particles is essential forthe user to determine if the data will be applicable to the individualsituation.3.3.2.2 CAS NumberThe unique registry number assignedby the Chemical Abstracts Service (CAS) of the
19、 AmericanChemical Society for each chemical component of the chal-lenge particles.3.3.2.3 Particle Size DistributionRelative volumetricconcentration of particles by physical size range, applicable ifvariable sized particles are utilized.3.3.2.4 SourceThe manufacturers code, model number,catalog numb
20、er or “brand name” which uniquely describes thechallenge particles.3.3.2.5 Lot Identification or Manufacture DateThe pro-duction lot or batch identification, or date, which uniquelyidentifies the challenge particles that were employed. If thisinformation cannot be found, enter the earliest date that
21、 theactual test sample was known to exist, for example, thepurchase data, the suppliers stocking date, the shipping date,date of receipt, or testing date, in a format such as “ReceivedJanuary 5, 1998.”3.3.3 Technique:3.3.3.1 Test Method UsedReference the specific testmethod used. Include the revisio
22、n year or version of the test. Ifa standard test is not used, list “none” and provide a completedescription of the method apparatus and procedure such thatsomeone else could duplicate the measurements.3.3.3.2 Deviation from Standard Test MethodSome test-ing situations may require modifications to th
23、e standard testmethod. Differences from the standard test method in terms ofconditioning, environment, apparatus, duration or challengemust be noted.3.3.3.3 Testing LaboratoryName, address, and telephonenumber of the testing laboratory.3.3.3.4 Analytical MethodThe method used to count andsize the ch
24、allenge particles, including a generic identificationof the method, description of the test system (if not included inthe test method) and identification of analyzers and compo-nents. The minimum and maximum particle size and particleconcentration that can be measured by the particle countersshould
25、be described.3.3.3.5 Temperature and HumidityThe temperature (C)and humidity (% RH) of the challenge air stream.3.3.3.6 Test Parameters that may not be Specified in theMethod:(1) Exposed Specimen AreaThe surface area, in m2,ofthe test specimen exposed to the challenge particles.(2) Flow RateThe aver
26、age air flow rate, m3/m2, andstandard deviation, through the test specimens. This value issometimes called face velocity and reported as m/s.(3) Pressure DropThe average pressure difference, inkPa, and standard deviation across the test specimens.(4) Challenge ConcentrationThe concentration of par-t
27、icles on the exposed side of the test specimen.(5) Test DurationThe length of time that the specimenswere exposed to the challenge particles.(6) Test SensitivityBased on the minimum detectablepercentage penetration and determined from the ratio of thelowest detectable concentration downstream of the
28、 test mate-rial divided by the challenge particle concentration.(7) Particle Size LimitationsThe particle size limitationsof the analytical method (largest and smallest particles observ-able)3.3.3.7 ControlsDescribe the positive controls used todemonstrate the reproducibility of the test.3.3.4 Test
29、Results:3.3.4.1 Date Tested:3.3.4.2 Number of Specimens TestedThe number of rep-licate specimens.3.3.4.3 Location of SpecimensThe part of the protectiveclothing from which the tested specimens were taken.3.3.4.4 Percent PenetrationThe observed penetration ofthe challenge particle through each specim
30、en of the testmaterial, expressed as a percentage. Calculate percent penetra-tion by dividing the downstream particles concentration (sam-pling side of specimen) by the upstream particle concentration(challenge side) and multiplying this ratio by 100. The reportmay report percent penetration for eac
31、h size range of particles.3.3.4.5 Other ObservationsThese may include data on thechange in penetration rate during the test, visual changes in thespecimens, such as caking of the challenge particle, fibrillationof the specimen surface, or changes in physical properties ofthe specimens.3.3.5 Source o
32、f DataThe name, address, and telephonenumber of the person completing the report.4. Keywords4.1 airborne particle; penetration; protective clothingF 2053 00 (2006)2ANNEX(Mandatory Information)A1. SUGGESTED FORMAT OF REPORTA1.1 Fig. A1.1 is the format to be followed when docu-menting the results of p
33、article penetration test on protectiveclothing materials.F 2053 00 (2006)3FIG. A1.1 Format of ReportF 2053 00 (2006)4ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly
34、advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, eit
35、her reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend
36、. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 2053 00 (2006)5
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1