ASTM F412-2016a Standard Terminology Relating to Plastic Piping Systems《有关塑料管道系统的标准术语》.pdf

1、Designation: F412 16F412 16aStandard Terminology Relating toPlastic Piping Systems1This standard is issued under the fixed designation F412; the number immediately following the designation indicates the year of originaladoption or, in the case of revision, the year of last revision.Anumber in paren

2、theses indicates the year of last reapproval.Asuperscriptepsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope Scope*1.1 This terminology is a compilation of definitions of technic

3、al terms used in the plastic piping industry. Terms that aregenerally understood or adequately defined in other readily available sources are not included.1.2 When a term is used in an ASTM document for which Committee F17 is responsible it is included only when judged, afterreview, by Subcommittee

4、F17.91 to be a generally usable term.1.3 Definitions that are identical to those published by other ASTM committees or other standards organizations are identifiedwith the committee number (for example, D20) or with the abbreviation of the name of the organization (for example, IUPACInternational Un

5、ion of Pure and Applied Chemistry).1.4 A definition is a single sentence with additional information included in notes.1.5 Definitions are followed by the committee responsible for the standard(s) (for example, F17.26) and standard numbers(s)in which they are used (for example, F714).2. Referenced D

6、ocuments2.1 ASTM Standards:2C114 Test Methods for Chemical Analysis of Hydraulic CementD256 Test Methods for Determining the Izod Pendulum Impact Resistance of PlasticsD638 Test Method for Tensile Properties of PlasticsD648 Test Method for Deflection Temperature of Plastics Under Flexural Load in th

7、e Edgewise PositionD747 Test Method for Apparent Bending Modulus of Plastics by Means of a Cantilever BeamD790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating MaterialsD882 Test Method for Tensile Properties of Thin Plastic SheetingD883 Terminol

8、ogy Relating to PlasticsD907 Terminology of AdhesivesD1003 Test Method for Haze and Luminous Transmittance of Transparent PlasticsD1079 Terminology Relating to Roofing and WaterproofingD1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion PlastometerD1488 Test Method for Amylaceous Ma

9、tter in AdhesivesD1505 Test Method for Density of Plastics by the Density-Gradient TechniqueD1527 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80 (Withdrawn 2013)3D1785 Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120D2104

10、 Specification for Polyethylene (PE) Plastic Pipe, Schedule 40 (Withdrawn 2010)3D2239 Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside DiameterD2241 Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series)D2282 Specification for Acrylonitrile

11、-Butadiene-Styrene (ABS) Plastic Pipe (Withdrawn 2006)31 This terminology is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.91 on Editorial andTerminology.Current edition approved Aug. 1, 2016Nov. 15, 2016. Published August

12、 2016January 2017. Originally approved in 1975. Last previous edition approved in 20152016 asF412 15.F412 16. DOI: 10.1520/F0412-16.10.1520/F0412-16A.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Stand

13、ardsvolume information, refer to the standards Document Summary page on the ASTM website.3 The last approved version of this historical standard is referenced on www.astm.org.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what chan

14、ges have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the offic

15、ial document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1D2444 Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of

16、a Tup (FallingWeight)D2447 Specification for Polyethylene (PE) Plastic Pipe, Schedules 40 and 80, Based on Outside Diameter (Withdrawn 2010)3D2513 Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and FittingsD2661 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plas

17、tic Drain, Waste, and Vent Pipe and FittingsD2666 Specification for Polybutylene (PB) Plastic Tubing (Withdrawn 2003)3D2680 Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer PipingD2683 Specification for Socket-Type Polyethylene Fittings for Outsi

18、de Diameter-Controlled Polyethylene Pipe and TubingD2737 Specification for Polyethylene (PE) Plastic TubingD2751 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings (Withdrawn 2014)3D2837 Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials

19、or Pressure Design Basis forThermoplastic Pipe ProductsD2846/D2846M Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution SystemsD3035 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside DiameterD3139 Specification for Joi

20、nts for Plastic Pressure Pipes Using Flexible Elastomeric SealsD3261 Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and TubingD3309 Specification for Polybutylene (PB) Plastic Hot- and Cold-Water Distribution SystemsD3350 Specification for Po

21、lyethylene Plastics Pipe and Fittings MaterialsF402 Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and FittingsF405 Specification for Corrugated Polyethylene (PE) Pipe and Fittings (Withdrawn 2015)3F441/F441M Specification for Chlorinated Pol

22、y(Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80F442/F442M Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe (SDRPR)F449 Practice for Subsurface Installation of Corrugated Polyethylene Pipe for Agricultural Drainage or Water Table ControlF628 Specification for Acryloni

23、trile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a CellularCoreF645 Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping SystemsF714 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside DiameterF771 Specification

24、 for Polyethylene (PE) Thermoplastic High-Pressure Irrigation Pipeline Systems (Withdrawn 2013)3F876 Specification for Crosslinked Polyethylene (PEX) TubingF877 Specification for Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution SystemsF891 Specification for Coextruded Poly(Vinyl Chlor

25、ide) (PVC) Plastic Pipe With a Cellular CoreF948 Test Method for Time-to-Failure of Plastic Piping Systems and Components Under Constant Internal Pressure With FlowF1025 Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holesin Polyethylene

26、 Gas Pressure PipeF1281 Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure PipeF1335 Specification for Pressure-Rated Composite Pipe and Fittings for Elevated Temperature Service (Withdrawn 2011)3F1473 Test Method for Notch Tensile Test to Measure the

27、Resistance to Slow Crack Growth of Polyethylene Pipes and ResinsF1488 Specification for Coextruded Composite PipeF1499 Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV)F1668 Guide for Construction Procedures for Buried Plastic PipeF1733 Specification for Butt Heat Fusion Polya

28、mide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and TubingF1760 Specification for Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic Pipe Having Reprocessed-RecycledContentF1924 Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Dist

29、ribution Pipeand TubingF1948 Specification for Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas DistributionPipe and TubingF1970 Specification for Special Engineered Fittings, Appurtenances or Valves for use in Poly (Vinyl Chloride) (PVC) orChlorinated Poly (Viny

30、l Chloride) (CPVC) SystemsF1973 Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11(PA11) and Polyamide 12 (PA12) Fuel Gas Distribution SystemsF1986 Specification for Multilayer PipeType 2, Compression Fittings, and Compression Joints fo

31、r Hot and Cold Drinking-WaterSystemsF1987 Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hydronic Heating SystemsF2145 Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside DiameterControlled Polyamide 11 and

32、 Polyamide 12 Pipe and TubingF2158 Specification for Residential Central-Vacuum Tube and FittingsF2160 Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD)F412 16a2F2176 Specification for Mechanical Couplings Used on Polyethylene Conduit, Du

33、ct and InnerductF2623 Specification for Polyethylene of Raised Temperature (PE-RT) SDR 9 TubingF2769 Specification for Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and DistributionSystemsF2788/F2788M Specification for Metric and Inch-sized Crosslinked Polyethylene (PE

34、X) PipeF2818 Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and TubingF2829/F2829M Specification for Metric- and Inch-Sized Crosslinked Polyethylene (PEX) Pipe SystemsF2905/F2905M Specification for Black Crosslinked Polyethylene (PEX) Line Pipe, Fitting

35、s and Joints For Oil and GasProducing ApplicationsF2929 Specification for Crosslinked Polyethylene (PEX) Tubing of 0.070 in. Wall and Fittings for Radiant Heating Systems upto 75 psigF2968/F2968M Specification for Black Crosslinked Polyethylene (PEX) Pipe, Fittings and Joints For Gas DistributionApp

36、lications2.2 ISO Standards:4ISO 3 Preferred NumbersISO 497 Preferred NumbersISO 12161 Thermoplastic materials for pipes and fittings for pressure applications Classification, designation and designcoefficientISO R 161 Pipes of Plastics Materials for the Transport of Fluids (Outside Diameters and Nom

37、inal Pressures) Part I, MetricSeriesISO TR 9080 Thermolplastics Pipes for the Transport of Fluids-Methods of Extrapolation of Hydrostatic Stress Rupture Datato Determine the Long-Term Hydrostatic Strength of Thermoplastic Pipe Materials2.3 ANSI Standard:4Z17.1 ANSI Preferred Numbers2.4 PPI Standard:

38、5PPI TR-43. Terminologyacceptance testingtesting performed on a product to determine whether or not an individual lot of the product conforms withspecified requirements. F17DISCUSSIONThe number of requirements are usually fewer than for qualification testing (see definition).acetal plastics, nhighly

39、 crystalline linear thermoplastic homopolymers or copolymers characterized by repeating oxymethyleneunits. F17acrylonitrile-butadiene-styrene (ABS) pipe and fitting plastics plastics containing polymers or blends of polymers, or both,in which the minimum butadiene content is 6%, the minimum acryloni

40、trile content is 15 %, the minimum styrene or substitutedstyrene content, or both, is 15 %, and the maximum content of all other monomers is not more than 5 %; plus lubricants,stabilizers, and colorants. F17.61 D1527, D2282 17.62 D2680, D2751adhesivea substance capable of holding materials together

41、by surface attachment. F17adhesive bonded jointsee joint, adhesive bonded.adhesive, solventsee solvent cement.adiabatic extrusiona method of extrusion in which, after the extrusion apparatus has been heated sufficiently by conventionalmeans to plastify the material, the extrusion process can be cont

42、inued with the sole source of heat being the conversion of thedrive energy, through viscous resistance of the plastic mass in the extruder. D20 D883aging, n(1) the effect on materials of exposure to an environment for an interval of time.(2) the process of exposing materials to an environment for an

43、 interval of time. D20 D883alloy, nin plastics, two or more immiscible polymers united, usually by another component, to form a plastic resin havingenhanced performance properties. D20 D883allowable stressThe maximum force per unit area that may be safely applied to a pipe.4 Available from American

44、National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http:/www.ansi.org.5 Available from Plastics Pipe Institute (PPI), 105 Decker Court, Suite 825, Irving, TX 75062, http:/www.plasticpipe.org.F412 16a3DISCUSSIONIn Guide F645, the allowable stress is determined by mult

45、iplying the hydrostatic design stress (HDS) at 73F by the temperature correction factor.F17.61 F645antioxidant, ncompounding ingredient used to retard deterioration caused by oxidation. F17apparent densitythe weight per unit volume of a material including voids inherent in the material as tested. F1

46、7DISCUSSIONThe term bulk density is commonly used for material such as molding powder.approving authoritythe individual official, board, department, or agency established and authorized by a state, county, city, orother political subdivision, created by law to administer and enforce specified requir

47、ements.artificial weatheringexposure to laboratory conditions, which may be cyclic, involving temperature, relative humidity, radiantenergy, or any other conditions or pollutants found in the atmosphere in various geographical areas; or both. F17DISCUSSIONThe interlaboratory exposure conditions are

48、usually intensified beyond those encountered in actual outdoor exposure in an attempt to achieve anaccelerated effect.backfillall material used to fill the trench from bedding to finished surface. F17.65 F449, F1668backfill, finalmaterial used to fill the trench from initial backfill to finished sur

49、face. F17backfill, initialmaterial used to fill the trench from top of bedding to a designated height over the pipe. F17backfill, pipe zonesee pipe zone backfill.backfill, unconsolidatednoncompacted material in place in trench. F17bead-up cycle, npart of the fusion procedure that insures complete contact between the heater surfaces and the pipe ends byapplying pressure such as fusion joining pressure to force the pipe ends against the heater surfaces.DISCUSSIONThe bead-up cycle begins at initial contact of the p