ASTM F441 F441M-2015 Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Schedules 40 and 80《氯化聚氯乙烯 (CPVC) 塑料管的标准规格 表40和80》.pdf

1、Designation: F441/F441M 131F441/F441M 15Standard Specification forChlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe,Schedules 40 and 801This standard is issued under the fixed designation F441/F441M; the number immediately following the designation indicates the yearof original adoption or, in th

2、e case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1 NOTEX1.7 w

3、as editorially revised in September 2013.1. Scope*1.1 This specification covers chlorinated poly(vinyl chloride) (CPVC) pipe made in Schedule 40 and 80 sizes and pressure-ratedfor water (see appendix). Included are criteria for classifying CPVC plastic pipe materials and CPVC plastic pipe, a system

4、ofnomenclature for CPVC plastic pipe, and requirements and test methods for materials, workmanship, dimensions, sustainedpressure, burst pressure, flattening, and extrusion quality. Methods of marking are also given.NOTE 1The CPVC pipe covered by this specification was covered previously in Specific

5、ation D1785.NOTE 2The sustained and burst pressure test requirements, and the pressure ratings in the appendix, are calculated from stress values obtained fromtests made on pipe 2 in. 50 mm and smaller. However, tests on larger pipe have shown these stress values to be valid.1.2 The products covered

6、 by this specification are intended for use with the distribution of pressurized liquids only, which arechemically compatible with the piping materials. Due to inherent hazards associated with testing components and systems withcompressed air or other compressed gases some manufacturers do not allow

7、 pneumatic testing of their products. Consult withspecific product/component manufacturers for their specific testing procedures prior to pneumatic testing.NOTE 3Pressurized (compressed) air or other compressed gases contain large amounts of stored energy which present serious saftey hazards shoulda

8、 system fail for any reason.1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notesand footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.1.4 The values stated in either

9、 SI units or inch-pound units are to be regarded separately as standard. The values stated in eachsystem may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from thetwo systems may result in non-conformance with the standard.1.5 The followi

10、ng safety hazards caveat pertains only to the test methods portion, Section 8, of this specification:This standarddoes not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety and health p

11、ractices and determine the applicability of regulatory limitations prior touse.A specific precautionary statement is given in Note 7.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Inte

12、rnal PressureD1599 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and FittingsD1600 Terminology for Abbreviated Terms Relating to PlasticsD1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)CompoundsD1785

13、 Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 1201 This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.25 on Vinyl BasedPipe.Current edition approved June 1, 2013Aug. 1,

14、2015. Published June 2013November 2015. Originally approved in 1974. Last previous edition approved in 20122013 asF441F441/F441M 12. 131. DOI: 10.1520/F0441_F0441M-13.10.1520/F0441_F0441M-15.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at servi

15、ceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. B

16、ecauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section ap

17、pears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and FittingsD2837 Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic

18、 Pipe Materials or Pressure Design Basis forThermoplastic Pipe ProductsF412 Terminology Relating to Plastic Piping Systems2.2 Federal Standard:Fed. Std. No. 123 Marking for Shipment (Civil Agencies)32.3 Military Standard:MIL-STD-129 Marking for Shipment and Storage32.4 NSF Standards:Standard No. 14

19、for Plastic Piping Components and Related Materials4Standard No. 61 for Drinking Water Systems ComponentsHealth Effects43. Terminology3.1 DefinitionsDefinitions are in accordance with Terminology F412, and abbreviations are in accordance with TerminologyD1600, unless otherwise specified. The abbrevi

20、ation for chlorinated poly(vinyl chloride) is CPVC.3.2 Definitions of Terms Specific to This Standard:3.2.1 hydrostatic design stressthe estimated maximum tensile stress the material is capable of withstanding continuously witha high degree of certainty that failure of the pipe will not occur. This

21、stress is circumferential when internal hydrostatic waterpressure is applied.3.2.2 pressure rating (PR)the estimated maximum water pressure the pipe is capable of withstanding continuously with a highdegree of certainty that failure of the pipe will not occur.3.2.3 relation between dimensions, desig

22、n stress, and pressure ratingThe following expression, commonly known as the ISOequation,5 is used in this specification to relate dimensions, hydrostatic design stress, and pressure rating:2S/P 5DO/t! 21where:S = hydrostatic design stress, psi MPa,P = pressure rating, psi MPa,DO = average outside d

23、iameter, in. mm, andt = minimum wall thickness, in. mm.3.2.4 standard thermoplastic pipe materials designation codeThe pipe materials designation code shall consist of theabbreviation CPVC for the type of plastic, followed by theASTM type and grade inArabic numerals and the design stress at 73F23C i

24、n units of 100 psi 0.7 MPa with any decimal figures dropped, followed by the design stress at 180F 82C in units of100 psi 0.7MPa with any decimal figures dropped. When the design stress code contains less than two figures, a cipher shall beused before the number. Thus a complete material code shall

25、consist of four letters and six figures for CPVC plastic pipe materials(see Section 5).4. Classification4.1 GeneralThis specification covers CPVC pipe made from one (see X1.2) CPVC plastic pipe material in Schedule 40 and80 sizes.4.2 Hydrostatic Design StressesThis specification covers CPVC pipe mad

26、e from CPVC plastic as defined by hydrostaticdesign stresses which have been developed on the basis of long-term tests (see appendix).NOTE 4This specification does not include requirements for pipe fittings intended to be used to vent combustion gases.5. Materials5.1 GeneralChlorinated poly(vinyl ch

27、loride) plastics used to make pipe meeting the requirements of this specification arecategorized by means of two criteria, namely, (1) short-term strength tests and (2) long-term hydrostatic strength tests at both 73and 180F 23 and 82C.5.2 Basic Materials:5.2.1 Basic Materials Short-term TestsThis s

28、pecification covers pipe made from CPVC plastics having certain physicalproperties as described in Specification D1784.3 Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/www.dodssp.daps.mil.4 Available from NSF Inte

29、rnational, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140, http:/www.nsf.org.5 ISO R 161-1960, Pipes of Plastics Materials for the Transport of Fluids (Outside Diameters and Nominal Pressures) Part 1, Metric Series.F441/F441M 1525.2.1.1 CompoundThe CPVC compounds used for this pipe sh

30、all equal or exceed the classification 23447 described inSpecification D1784.5.2.2 Basic Materials Long-term TestThis specification convers pipe made from CPVC plastics having certain HydrostaticDesign Bases (HDB) and Hydrostatic Design Stresses (HDS) described in Test Method D28375.2.2.1 CompoundTh

31、e CPVC compounds used for this pipe shall have a Hydrostatic Design Basis at 73F 23C of 4000 psi28 MPa, , MPa and a Hydrostatic Design Basis at 180F 82C of either 1000 psi 7.0 MPa or 1250 psi 8.6 MPa whenevaluated in accordance with Test Method D28375.2.3 Standard thermoplastic pipe materials design

32、ation The pipe materials designation shall consist of the materialdesignation code CPVC 4120-05 or CPVC 4120-06 for the type of plastic.NOTE 5As per Terminology F412 (see, “code, thermoplastic pipe materials designation”) the pipe materials designation code CPVC 4120 is asfollows: CPVC is the abbrev

33、iation for chlorinated poly(vinyl chloride) as per Terminology D1600, 41 represents Cell Classification 23447 perSpecification D1784, and 20 represents a HDS of 2000 psi 14 MPa for water at 73F (23C) per Test Method D2837. In addition, the -05 or -06 suffixrepresents a HDS of 500 psi 3.4 MPa or 625

34、psi 4.3 MPa respectively for water at 180F 82C per Test Method D2837.5.3 Rework MaterialThe manufacturers shall use only their own clean rework pipe material and the pipe produced shall meetall the requirements of this specification.6. Requirements6.1 Dimensions and Tolerances:6.1.1 Dimensions and t

35、olerances shall be as shown in Table 1 and Table 2 when measured in accordance with Test MethodD2122. The tolerances for out-of-roundness shall apply only to pipe prior to shipment.6.1.2 Wall Thickness RangeThe wall thickness range shall not exceed 12 % when measured in accordance with Test MethodD2

36、122.6.2 Sustained PressureThe pipe shall not fail, balloon, burst, or weep as defined in Test Method D1598, at the test pressuresgiven in Table 3, when tested in accordance with 8.4.6.2.1 Accelerated Regression TestThe accelerated regression test shall be used in place of both the sustained and burs

37、tpressure tests at the option of the manufacturer. The test shall be conducted in accordance with 8.4.1. The pipe shall demonstratea hydrostatic design basis projection at the 100 000 h intercept that meets the hydrostatic design basis category requirement (seeTable 1, Test Method D2837) for the CPV

38、C material used in its manufacture. If the lower confidence value at 100 000 h differsTABLE 1 Outside Diameters and Tolerances for CPVC Plastic Pipe, Schedules 40 and 80, in. mmTolerancesMaximum Out-of-Roundness(maximum minus minimum diameter)Nominal Pipe Size Outside Diameter Schedule 40 sizes312 i

39、n. and over;Schedule 80sizes 8 in. and overSchedule 40 sizes3 in. and less;Schedule 80 sizes6 in. and less14 8 0.540 13.7 0.004 0.10 . 0.016 (0.41)38 10 0.675 17.1 0.004 0.10 . 0.016 (0.41)12 15 0.840 21.3 0.004 0.10 . 0.016 (0.41)34 20 1.050 26.7 0.004 0.10 . 0.020 (0.51)1 25 1.315 33.4 0.005 0.13

40、. 0.020 (0.51)114 32 1.660 42.2 0.005 0.13 . 0.024 (0.61)112 40 1.900 48.3 0.006 0.15 . 0.024 (0.61)2 50 2.375 60.3 0.006 0.15 . 0.024 (0.61)212 65 2.875 73.0 0.007 0.18 . 0.030 (0.76)3 80 3.500 88.9 0.007 0.18 . . . 0.023 (0.58)312 90 4.000 101.6 0.008 0.20 0.100 (2.54) 0.030 (0.76)312 90 4.000 101

41、.6 0.008 0.20 0.100 (2.54) 0.030 (0.76)4 100 4.500 114.3 0.008 0.20 0.100 (2.54) 0.023 (0.58)4 100 4.500 114.3 0.008 0.20 0.100 (2.54) 0.023 (0.58)5 125 5.563 141.3 0.010 0.25 0.100 (2.54) 0.060 (1.52)5 125 5.563 141.3 0.010 0.25 0.100 (2.54) 0.060 (1.52)6 150 6.625 168.3 0.011 0.28 0.100 (2.54) 0.0

42、70 (1.78)6 150 6.625 168.3 0.011 0.28 0.100 (2.54) 0.070 (1.78)8 200 8.625 219.1 0.015 0.38 0.150 (3.81) 0.090 (2.29)8 200 8.625 219.1 0.015 0.38 0.150 (3.81) 0.090 (2.29)10 250 10.750 273.1 0.015 0.38 0.150 (3.81) 0.100 (2.54)12 300 12.750 323.9 0.015 0.38 0.150 (3.81) 0.120 (3.05)14 350 14.000 355

43、.6 0.015 0.380 0.200 (5.08) .16 400 16.000 406.4 0.019 0.480 0.320 (8.13) .18 450 18.000 457.2 0.019 0.480 0.360 (9.14) .20 500 20.000 508.0 0.023 0.580 0.400 (10.2) .24 600 24.000 609.6 0.031 0.790 0.480 (12.2) .F441/F441M 153from the extrapolated LTHS value by more than 15 % of the latter; or M in

44、Appendix X2 (Test Method D2837) is zero or negative;or b in the equation h = a + bf in Appendix X1 (Test Method D2837) is positive, consider the data unsuitable.6.3 Burst PressureThe minimum burst pressures for CPVC plastic pipe shall be as given in Table 4, when determined inaccordance with Test Me

45、thod D1599.6.4 FlatteningThere shall be no evidence of splitting, cracking, or breaking when the pipe is tested in accordance with 8.5.7. Workmanship, Finish, and Appearance7.1 The pipe shall be homogeneous throughout and free from visible cracks, holes, foreign inclusions, or other defects. The pip

46、eshall be as uniform as commercially practicable in color, opacity, density, and other physical properties.NOTE 6Color and transparency or opacity should be specified in the contract or purchase order.8. Test Methods8.1 ConditioningCondition the test specimens at 73.4 6 3.6F 23 6 2C and 50 6 5 % rel

47、ative humidity for not less than40 h prior to test in accordance with Procedure A of Practice D618, for those tests where conditioning is required.8.2 Test ConditionsConduct tests in the standard laboratory atmosphere of 73 6 3.6F 23 6 2C and 50 6 5 % relativehumidity, unless otherwise specified in

48、the test methods or in this specification.8.3 SamplingThe selection of the sample or samples of pipe shall be as agreed upon by the purchaser and the seller. In caseof no prior agreement, any sample selected by the testing laboratory shall be deemed adequate.8.3.1 Test SpecimensNot less than 50 % of the test specimens required for any pressure test shall have at least a part of themarking in their central sections. The central section is that portion of pipe which is at least one pipe diameter away from an endclosure.8.4 Sustained Pressure TestSelect the test specimens at r