ASTM F486-2001(2011) Standard Practice for Preparation of Use and Care Booklets for Vacuum Cleaners 《真空吸尘器的使用和保养手册的编制的标准操作规程》.pdf

1、Designation: F486 01 (Reapproved 2011)An American National StandardStandard Practice forPreparation of Use and Care Booklets for Vacuum Cleaners1This standard is issued under the fixed designation F486; the number immediately following the designation indicates the year of originaladoption or, in th

2、e case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice identifies the information to be providedthrough the use and care bookle

3、t accompanying a particularmodel of vacuum cleaner.1.2 Included is information that the user needs to operateand maintain the vacuum cleaner and the attachments providedin a proper and safe manner.1.2.1 Similar information is included for attachments thatare sold separately.2. Referenced Documents2.

4、1 ASTM Standards:2F395 Terminology Relating to Vacuum Cleaners2.2 ANSI Standard:3ANSI/UL 1017 Standard for Safety for Vacuum Cleaners,Blower Cleaners, and Household Floor Finishing Ma-chines3. Terminology3.1 Definitions:3.1.1 Refer to Terminology F395.4. Significance and Use4.1 The user must underst

5、and how to operate and maintainthe equipment to achieve satisfactory cleaning results. Sincethe manufacturers are the prime source of this information, it istheir responsibility to provide instructions for specific models.Clear, concise, simple (but complete) instructions for the safeuse and mainten

6、ance will encourage users to read the informa-tion and follow proper procedures. This will increase usersatisfaction, minimize safety problems, and decrease com-plaints.5. General Requirements5.1 Information pertinent to the proper and safe manner ofoperating and maintaining the vacuum cleaner and i

7、ts providedattachments should be included in the booklet.5.1.1 Similar information should be included for attach-ments that are sold separately.5.2 Format:5.2.1 Ideally, there should be one booklet for each model.However, similar models may be contained in one booklet. Thedifferences between the mod

8、els should be precisely and clearlyshown in the booklet by illustrations and wording.5.2.2 All models included in the booklet should be identi-fied by model name or series on the front cover along with aphotograph or drawing of the basic model.5.2.3 The size of the booklet should be no larger than 8

9、12 by11 in. (216 by 279 mm) and no smaller than 5 by 7 in. (127 by178 mm) in size.5.2.4 The wording in the booklet should be as nontechnicalas possible.5.2.5 Illustrations and wording should be used to identifyvacuum cleaner parts, attachments, and features.5.2.6 Instructions for maintenance, storag

10、e, assembly, anddisassembly of the product by the user should be accompaniedby illustrations as well as wording.6. Content6.1 There should be a section on each of the followingsubjects in the use and care booklet or on separate sheets thataccompany it. When separate sheets are used they should beref

11、erenced in the use and care booklet:6.1.1 Cover, with identification of the product(s) and spe-cific model(s),6.1.2 Table of contents, if needed for clarity,6.1.3 Important safeguards in use and care,6.1.4 Illustration of vacuum cleaner with major componentsand attachments identified,6.1.5 Explanati

12、on and illustration of user assembly proce-dure and identification of parts to be assembled,6.1.6 List of cleaning attachments provided with thevacuum cleaner. Instructions on how to connect and disconnectattachments. Information and suggestions on the uses for eachattachment. Special instructions (

13、if any) on storage of attach-ments on the vacuum cleaner.6.1.7 Instructions on how to operate the vacuum cleaner,1This practice is under the jurisdiction of ASTM Committee F11 on VacuumCleaners and is the direct responsibility of Subcommittee F11.93 on ConsumerInformation.Current edition approved No

14、v. 1, 2011. Published March 2012. Originallyapproved in 1976. Last previous edition approved in 2006 as F486 01 (2006).DOI: 10.1520/F0486-01R11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards v

15、olume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United St

16、ates.6.1.8 Information on “special” features (for example: speedselector, cord reel, wet pick up, etc.),6.1.9 Explanation of dirt or water receptacle. Instructions onhow to determine when and how to empty, clean, and replace,6.1.10 Instructions on when and how to clean or replacefilters,6.1.11 Recom

17、mended storage of vacuum cleaner and attach-ments,6.1.12 Recommended user care and maintenance of vacuumcleaner and attachments (that is, agitator belts, cleaningbrushes, light bulbs, dirt receptacle, etc.),6.1.13 Recommended preventive maintenance service,6.1.14 Troubleshooting check list,6.1.15 Se

18、rvice facilities,6.1.16 Procedure and possible sources for purchasing re-placement parts,6.1.17 Written warranties,6.1.18 Title and address of customer relations contact, and6.1.19 Additional information deemed necessary by law, bylisting or certification agencies, or both, or by the manufactureror

19、distributors.7. Keywords7.1 instruction book; vacuum cleanerASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such pa

20、tent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited ei

21、ther for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair

22、 hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this stan

23、dard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F486 01 (2011)2