ImageVerifierCode 换一换
格式:PDF , 页数:3 ,大小:60.66KB ,
资源ID:536792      下载积分:5000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-536792.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM F498-1977(2006) Standard Test Method for Center Spring Constant and Spring Constant Balance of Alpine Skis《高山滑雪板的中心弹性常数及弹性常数平衡的试验方法》.pdf)为本站会员(deputyduring120)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ASTM F498-1977(2006) Standard Test Method for Center Spring Constant and Spring Constant Balance of Alpine Skis《高山滑雪板的中心弹性常数及弹性常数平衡的试验方法》.pdf

1、Designation: F 498 77 (Reapproved 2006)Standard Test Method forCenter Spring Constant and Spring Constant Balance ofAlpine Skis1This standard is issued under the fixed designation F 498; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revisi

2、on, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of centerspring constant, forebody spring constant, and aft

3、erbody springconstant of Alpine skis. In addition, it covers a method fordetermination of the spring constant balance.1.2 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-pria

4、te safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Terminology2.1 Definitions:2.1.1 afterbody spring constantthe load, in newtons, re-quired to deflect point A a distance of 1 cm.CA5FAfm(1)2.1.2 center spring constantthe load, in newtons, requir

5、edto deflect point M a distance of 1 cm.CM5FMfm(2)2.1.3 deflection fthe displacement of the ski under load Fmeasured at points A, B, or M normal to a line between supportpoints or the clamping plane.2.1.4 forebody spring constantthe load, in newtons, re-quired to deflect point B a distance of 1 cm.C

6、B5FBfB(3)2.1.5 load Fthe force applied normal to the support pointsor the clamping plane, at points A, B, or M. The onlycomponent of load F is shown in Fig. 1.2.1.6 point Athe support point for the afterbody of the skiwhen the center spring constant is measured or the loadapplication point when the

7、afterbody spring constant is mea-sured.2.1.7 point Bthe support point for the forebody of the skiwhen the center spring constant is measured or the loadapplication point when the forebody spring constant is mea-sured.2.1.8 point Mthe load application point when the centerspring constant is measured

8、and the clamping point when theforebody spring constant or the afterbody spring constant ismeasured. It is located at the midpoint between points A and B.2.1.9 ski size, xplthe projected length with the ski bodypressed flat against a plane surface, measured between the skitail and the ski tip, commo

9、nly referred to as chord length. Thedeveloped or material length is the length from tip to tail alongthe bottom contour of the ski.2.1.10 spring constanta measurement of the stiffness of aski in bending, expressed as a ratio of force to deflection.2.1.11 spring constant balancethe ratio of afterbody

10、spring constant divided by forebody spring constant.B 5CACB(4)3. Preparation of Apparatus3.1 Center Spring Constant EquipmentEquip supports Aand B with low-friction rolls of 2.0 6 0.1 cm diameter. Applythe load with a dynamometer or calibrate the measurement ofload with an accuracy of 60.5 N. Measur

11、e the deflection witha suitable instrument with an accuracy of 60.005 cm. Applythe load with a cylindrical contact ram having a radius of 1.06 0.1 cm and extending over the width of the ski.3.2 Forebody and Afterbody Spring Constant EquipmentProvide a clamping fixture to grip the ski as a vise with

12、a flatrigid jaw and three clamps with at least 15-cm spacing betweenthem. Locate one clamp at each end and one in the center.Clamps should be at least 3 cm wide covering the width of theski. Apply the load with a cylindrical contact ram having aradius of 1.0 6 0.1 cm and covering the width of the sk

13、i.4. Procedure (See Fig. 2)4.1 Center Spring ConstantPlace the supports at points Aand B. The location of point A is 5 6 1 cm from the tail of theski. The location of point B is a distance of C (C = xpl25cm(6 1 cm) from point A or equivalent to 20 6 1 cm from the1This test method is under the jurisd

14、iction of ASTM Committee F27 on SnowSkiing and is the direct responsibility of Subcommittee F27.30 on Skis and Boots.Current edition approved Oct. 1, 2006. Published December 2006. Originallyapproved in 1977. Last previous edition approved in 1998 as F 498 77 (1998).1Copyright ASTM International, 10

15、0 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.tip of the ski. Apply a load of 300 6 2 N to the ski. Readdeflection within 2 to 5 s after load application with anaccuracy of 60.05 cm.4.2 Afterbody Spring Constant and Forebody SpringConstantMount the ski to the clam

16、ping plate in a way thatthe ski forebody or ski afterbody can be bent freely from pointM. Apply a load of 50 6 0.5 N at point A or B normal to theline extended from the clamping plates. Read deflection within2 to 5 s after load application and measure it normal to theclamping plates with an accuracy

17、 of 0.05 cm.5. Report5.1 The report shall include the following:5.1.1 ASTM F 498,5.1.2 Brand, designation of model, manufacturers registra-tion number, and size of ski, and5.1.3 Results of center spring constant, forebody springconstant, afterbody spring constant, and spring constant bal-ance.6. Pre

18、cision and Bias6.1 The precision and bias of this test method is currentlybeing determined.27. Keywords7.1 Alpine skis; spring constants2Supporting data have been filed at ASTM International Headquarters and maybe obtained by requesting Research Report RR:F08-1001.FIG. 1 Physical Dimensions of Alpin

19、e Ski(a) Center Spring Constant.(b) Forebody Spring Constant.(c) Afterbody Spring Constant.FIG. 2 Loading MethodsF 498 77 (2006)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard ar

20、e expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not

21、revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which yo

22、u may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 498 77 (2006)3

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1