ASTM F670-2002(2012) Standard Specification for Tanks 5 and 10-Gal (20 and 40-L) Lube Oil Dispensing《5和10 加仑 (20和40 升) 的润滑油配料容器的标准规范》.pdf

1、Designation: F670 02 (Reapproved 2012) An American National StandardStandard Specification forTanks, 5 and 10-Gal (20 and 40-L) Lube Oil Dispensing1This standard is issued under the fixed designation F670; the number immediately following the designation indicates the year of originaladoption or, in

2、 the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 Th

3、is specification covers the material, dimensions, andconstruction of 5 and 10-gal (20 and 40-L) tanks purchased tostore and dispense lubricating oils. The tanks are industrialsafety cans mounted on a T-bar bracket, complete with driptray.1.2 The values stated in inch-pound units are to be regardedas

4、 the standard. The values given in parentheses are forinformation only.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine th

5、e applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2A36/A36M Specification for Carbon Structural SteelA108 Specification for Steel Bar, Carbon and Alloy, Cold-FinishedA164 Specification for Electrodeposited Coatings of Zinc onSteel; Replaced by B 663 (W

6、ithdrawn 1981)3A167 Specification for Stainless and Heat-ResistingChromium-Nickel Steel Plate, Sheet, and StripA308/A308M Specification for Steel Sheet, Terne (Lead-TinAlloy) Coated by the Hot-Dip ProcessA569/A569M Specification for Steel, Carbon (0.15Maximum, Percent), Hot-Rolled Sheet and Strip Co

7、mmer-cial (Withdrawn 2000)33. Ordering Information3.1 Orders for tanks under this specification shall includethe following:3.1.1 Quantity (number),3.1.2 Size, either 5 or 10 gal (20 or 40 L),3.1.3 Purchase option for finished tank materials: Terneplate (4.1.3), and3.1.4 ASTM designation and year of

8、issue.3.2 If only size, quantity, and ASTM designation are speci-fied and no purchase options are specified, then suppliers shallfurnish all stainless steel tanks, brass faucets with flasharrestors, and painted steel mounting columns with bolt-on driptray assemblies, which include perforated steel t

9、ray liners,drain plugs, drilled mounting holes, and mounting bolts.3.3 Optional packaging/shipping.3.3.1 If required for shipping, tanks shall be packagedindividually in cartons suitable for freight handling.4. Materials and Manufacture4.1 Materials:4.1.1 316 Stainless Steel Sheet (Specification A16

10、7), mini-mum thickness 24 gage (0.6 mm) on tank body, 22 gage (0.8mm) on tank top and bottom; body bracket, filler spout, flasharrestor, vacuum breaker valve and linkage.4.1.2 316 Stainless Steel Cast, Wrought, or Forged Flanges,(for faucet and drain).4.1.3 Terne Plate Sheet (purchase option), minim

11、um thick-ness 22 gage (0.8 mm) on tank body, top and bottom: bodybracket, filler spout (Specification A308/A308M).4.1.4 Mild Steel:4.1.4.1 Bolt-On Column Stand, T-section, hot-rolled (Speci-fication A36/A36M); minimum thickness 0.160 in. (4 mm). .4.1.4.2 Drip Tray Bracket, round edge, hot-rolled (Sp

12、ecifi-cation A569/A569M).4.1.4.3 Drip Tray Assembly, hot or cold-rolled (Specifica-tion A108).4.1.4.4 Drip Tray Liner, 11-gage (3 mm), zinc-plated(Specification A164).4.1.4.5 Filler Spout Cover, zinc-plated steel (SpecificationA164).4.1.4.6 Drip Tray Drain,34-in. (20 mm) NPS drain.4.1.5 Cast Brass:1

13、This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved June 1, 2012. Published October 2012. Originallyapproved in 1980. Last previous edition ap

14、proved in 2007 as F670 - 02 (2007). DOI:10.1520/F0670-02R12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3

15、The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1DimensionsSizeAHeight, in.BBolt Hole Spacing, in.CTank Height, in.DNumber of Bolt HolesWeight, lbDry We

16、t (Water)5-gal 2212 1012 978 3398110-gal 3334 1012 2078 4 49 132Note 1Dimensions and construction for guidance only.Note 21 in. = 25.4 mm.Note 31 lb = 0.4536 Kg.FIG. 1 Dimension of TankF670 02 (2012)24.1.5.1 Faucet, lever-lock, self-closing,34-in. (20mm) outside diameter, male threaded.44.1.5.2 Drip

17、 Tray Drain Plug and Tank Bottom Drain Plug,34-in. (20 mm) NPS.4.1.6 Cast Aluminum, self-closing, spring-action type, one-piece, filler spout cover lever.4.2 ManufactureAll sheet metal seams shall be welded.5. Dimensions and Weight5.1 The dimensions in Fig. 1 are recommended nominaldimensions. Weigh

18、ts are estimated and are not critical. Volumeof tanks shall be 5 and 10 gal (20 and 40 L), respectively.6. Workmanship, Finish, and Appearance6.1 Workmanship on tank, stand, and drip pan shall be ofsufficient quality to prevent dirt accumulation. Welding shallhave small, even beading, free of slag a

19、nd spatter. Surface ofall castings shall be of uniform texture, without cracks, pitting,or flashing. Stand and drip tray shall have corners broken andall burrs removed.6.2 Tank, column, bracket, and tray shall be covered withone coat 1.5 mils (0.05 mm) thick of a zinc rich primer. Thestainless steel

20、 tank shall have no paint.7. Testing Methods7.1 Test each tank by subjecting to an internal air pressureof 5 psi (35 kPa) with no visible seam leakage when subjectedto underwater or soap bubble test.8. Keywords8.1 lubricating oil tanks; marine; marine storage tanks;marine technology; oil dispensers;

21、 ships; tanksASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of suc

22、h rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for addit

23、ional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the

24、 ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the

25、aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).4Protectoseal 531G, available from The Protectoseal Co., 225 Foster Ave.,Bensenville, IL 60106, or equivalent, has been found suitable for this purpose.F670 02 (2012)3