ASTM F707 F707M-1994(2011) Standard Specification for Modular Gage Boards《组合式量规板标准规范》.pdf

1、Designation: F707/F707M 94 (Reapproved 2011)An American National StandardStandard Specification forModular Gauge Boards1This standard is issued under the fixed designation F707/F707M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision,

2、 the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification cover

3、s modular gauge boards formounting 89-mm (312-in.), 114-mm (412-in.), 152-mm (6-in.),and 216-mm (812-in.) dial size pressure gauges and dialthermometers for miscellaneous shipboard applications.1.2 Gauge boards ordered under this specification are suit-able for pressure gauges and dial thermometers

4、with eitherturret or back flanged type cases and with either back or bottomconnections (see Appendix X1).1.3 Gauge mounting dimensions shall be in accordance withANSI B 40.011.4 The values stated in SI units are to be regarded as thestandard. The inch-pound values given in parentheses are forinforma

5、tion only.NOTE 1Gauge boards covered by this specification are those normallysupplied by the shipyard as opposed to the shipyards equipment subcon-tractor.2. Referenced Documents2.1 Other Standards:B 40.1 Gauges, Pressure and Vacuum, Indicating DialTypeElastic Element2Fed Spec. TT-P-645 Primer, Pain

6、t, Zinc-Chromate, AlkydType3DoD-P-15328 Primer (Wash), Pretreatment (Formula No.117 for Metals) (Metric)33. Classification3.1 Gauge boards are furnished in two types as follows:3.1.1 Type IGauge boards for mounting 89-mm (312-in.)and 114-mm (412-in.) dial size gauges as specified in Section 5.3.1.2

7、Type IIGauge boards for mounting 152-mm (6-in.)and 216-mm (812-in.) dial size gauges as specified in Section5.3.2 Gauge boards are furnished in two grades as follows:3.2.1 Grade aGauge boards are to be manufactured fromcarbon steel as specified in Section 5.3.2.2 Grade bGauge boards are to be manufa

8、ctured fromaluminum alloy as specified in Section 5.4. Ordering Information4.1 Orders for gauge boards under this specification shallinclude the following information:4.1.1 Quantity (number of gauge boards),4.1.2 Name of item (gauge board),4.1.3 Type (Type I or Type II as specified by purchaser), se

9、e3.1.1 and 3.1.2,4.1.4 Grade (Grade a or Grade b as specified by purchaser),see 3.2.1 and 3.2.2,4.1.5 Paint (as specified by purchaser), see 7.2,4.1.6 Drilling for gauge mounting (as specified by pur-chaser), see 5.1.1, and4.1.7 ASTM designation and date of issue.5. Materials and Manufacture5.1 Unle

10、ss otherwise specified the gauge boards shall bemanufactured from 11-gauge (manufacturers standard gauge)carbon steel for Grade a and 3 mm (18 in.) thick aluminumalloy for Grade b. Materials shall be capable of being bent atroom temperature through 90 in any direction to an insideradius equal to its

11、 thickness without cracking on the outside ofthe bent portion.5.1.1 Unless otherwise specified, Type I gauge boards shallbe drilled for mounting both 89-mm (312-in.) and 114-mm(412-in.) dial size gauges and Type II gauge boards shall bedrilled for mounting both 152-mm (6-in.) and 216-mm (812-in.) di

12、al size gauges. When specified by the purchaser, drillingshall be limited to one size gauge for either Type I or Type IIgauge boards (see 4.1.6).1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.11 o

13、nMachinery and Piping Systems.Current edition approved April 1, 2011. Published April 2011. Originallyapproved in 1981. Last previous edition approved in 2006 as F707/F707M 94(2006). DOI: 10.1520/F0707_F0707M-94R11.2Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floo

14、r, New York, NY 10036, http:/www.ansi.org.3Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/dodssp.daps.dla.mil.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, Uni

15、ted States.6. Dimensions and Permissible Variations6.1 The dimensions of the gauge board shall not vary bymore than 0.4 mm (6164 in.) except as noted in Fig. 1 and Fig.2.7. Workmanship, Finish and Appearance7.1 The gauge boards shall have a workmanlike finish freeof scale, burrs, cracks, and other d

16、efects affecting serviceabilityor appearance.7.2 If paint is not specified by the purchaser, Grade a gaugeboards shall be supplied with a coat of zinc chromate primer inaccordance with Federal Specification TT-P-645, Formula 84or equal (yellow) 0.038-mm (1.5-mils) dry film thickness.Grade b gauge bo

17、ards shall be supplied with one pretreatmentwash coat in accordance with Specification DOD-P-15328Formula 117 or equal (dark green) 0.013-mm (0.5-mils) dryfilm thickness and one coat of zinc chromate primer inaccordance with Federal Specification TT-P-645 Formula 84Dor equal (dark green) 0.013 mm (1

18、.5-mils) dry film thickness.8. Product Marking8.1 Each shipping unit shall bear a tag or be plainly markedwith the following: ASTM designation number, name ortrademark of manufacturer, number of pieces, and purchaseorder number.9. Keywords9.1 dial pressure gauges; dial thermometers; modular gaugeboa

19、rds; pressure gaugesFIG. 1 Gauge Board Type IF707/F707M 94 (2011)2APPENDIX(Nonmandatory Information)X1. RATIONALE USED FOR DEVELOPMENT OF SPECIFICATION FOR MODULAR GAUGE BOARDSX1.1 This specification has been developed primarily toprovide maximum versatility for the installation of 89-mm(312-in.), 1

20、14-mm (412-in.), 152-mm (6-in.), and 216-mm(812-in.) dial size simplex, duplex, and differential pressuregauges and dial thermometers with either turret- or back-flanged cases (see Fig. X1.1 Fig. X1.2 Fig. X1.3).X1.2 The gauge board is suitable for single-gauge instal-lation, but has the versatility

21、 of being bolted together horizon-tally, vertically, in pyramid fashion or a combination thereof toFIG. 2 Gauge Board Type IIFIG. X1.1 Bottom- and Back-Connected Pressure Gauges for Horizontal Installations of Type I or Type II Gauge BoardsF707/F707M 94 (2011)3provide for multigauge installations ut

22、ilizing both Type I andType II gauge boards.X1.3 When used in horizontally arranged installations,either bottom or back connected pressure gauges and dialFIG. X1.2 Back-Connected Pressure Gauges for Vertical or Combined Vertical, Horizontal, and Pyramid Arrangements of Type I or TypeII Gauge BoardsF

23、IG. X1.3 Back Connected Type I and Type II Gauge Boards Combined For Vertical, Horizontal, and Pyramid ArrangementsF707/F707M 94 (2011)4thermometers may be used. When used vertically or in com-bination with vertical, horizontal, or pyramid arrangements,back connected pressure gauges and dial thermom

24、eters must beused.X1.4 This specification does not cover flush-mountedgauges.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validi

25、ty of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your commen

26、ts are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have no

27、t received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple cop

28、ies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F707/F707M 94 (2011)5