ImageVerifierCode 换一换
格式:PDF , 页数:4 ,大小:73.16KB ,
资源ID:537233      下载积分:5000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-537233.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM F762 F762M-2008(2014) Standard Test Method for Determining Change in Groove &40 or Void&41 Depth With Distance Traveled for Passenger Car Tires《测量客车随行驶距离引起的轮胎槽 (或者沟纹) 深度变化的标准试.pdf)为本站会员(bonesoil321)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ASTM F762 F762M-2008(2014) Standard Test Method for Determining Change in Groove &40 or Void&41 Depth With Distance Traveled for Passenger Car Tires《测量客车随行驶距离引起的轮胎槽 (或者沟纹) 深度变化的标准试.pdf

1、Designation: F762/F762M 08 (Reapproved 2014)Standard Test Method forDetermining Change in Groove (or Void) Depth WithDistance Traveled for Passenger Car Tires1This standard is issued under the fixed designation F762/F762M; the number immediately following the designation indicates the yearof origina

2、l adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers a procedure to be used to obtaindata for d

3、etermining the changes in tire tread depth over anyspecified course and test period.1.2 The tire tread depth loss data obtained according to theprocedures for this test method may be used to calculate tiretread wear by way of the procedures described in PracticeF1016.1.3 The values stated in either

4、SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.1.4 This standard d

5、oes not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM St

6、andards:2F421 Test Method for Measuring Groove and Void Depth inPassenger Car TiresF457 Test Method for Speed and Distance Calibration ofFifth Wheel Equipped With Either Analog or DigitalInstrumentationF538 Terminology Relating to the Characteristics and Per-formance of TiresF1016 Practice for Linea

7、r Tire Treadwear Data AnalysisF1502 Test Method for Static Measurements on Tires forPassenger Cars, Light Trucks, and Medium Duty Vehicles3. Terminology3.1 Definitions:3.1.1 break-in, none or more periods of initial standard-ized tire operation during which tire is brought to the statewhich will lea

8、d to more consistent test results. F5383.1.2 element, nan isolated (totally bounded by void)projection. F5383.1.3 groove, na void that is relatively narrow comparedto its length. F5383.1.4 groove (void) average depth, nthe average depth ofall groove depth measurements in a single groove. F5383.1.5 g

9、roove (void) depth, L, na measurement of theperpendicular distance from a real or calculated reference planedefined by edges of two adjacent ribs or elements to the lowestpoint of contact in the groove (void). F5383.1.6 irregular wear, na type of treadwear characterizedby substantial variations of t

10、read loss both from projection toprojection and frequently from point to point on a givenprojection. F5383.1.7 measurement interval, nthe distance travelled, inkilometres miles, between two successive groove (void)depth measurements. F5383.1.7.1 DiscussionA specified number of test cycles willconsti

11、tute a measurement interval. If a tire rotation plan isspecified, the measurement interval shall include equal dis-tance on each specified wheel position for each tire testspecimen. More frequent measurements may be made ifdesired. The number of measurement intervals should becompatible with the tir

12、e rotation plan to result in a logical basisfor data interpretation.3.1.8 projection, na pavement contacting area of the treadband, bounded by void. F5383.1.9 rib, na continuous circumferential projection. F5383.1.10 rotation plan, n in tire testing, the scheduledchange of wheel positions for all ti

13、res on a vehicle, andbetween vehicles in a convoy, and scheduled change of vehicleposition in a convoy during a road test as appropriate. F5383.1.10.1 DiscussionTest tires should occupy each positionon the vehicle for the same number of cycles. A tire rotation1This test method is under the jurisdict

14、ion of ASTM Committee F09 on Tiresand is the direct responsibility of Subcommittee F09.30 on Laboratory (Non-Vehicular) Testing.Current edition approved June 1, 2014. Published November 2014. Originallyapproved in 1982. Last previous edition approved in 2008 as F762/F762M 08.DOI: 10.1520/F0762_F0762

15、M-08R14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive,

16、PO Box C700, West Conshohocken, PA 19428-2959. United States1plan may be designed for each test in accordance with therequirement of the test program.3.1.11 test cycle, nin tire testing, one complete circuit ofthe specified test course. F5383.1.12 tread depth average, n in a single tire, the average

17、of all tire groove (void) depth measurements.3.1.13 void, na volume (in the tread band) defined by thelack of rubber; the depth dimension of the volume may varyfrom point to point in (on) the tread band. F5384. Summary of Test Method4.1 The tire test procedure is carried out by repeatedlydriving one

18、 or more test vehicles over a specified test course.All tires on each test vehicle are of the same tire sizedesignation: duplicate tires are mounted on each axle. Abreak-in period prior to the measurement program is optional.The tires may be rotated among wheel positions after comple-tion of a speci

19、fied number of runs over the test course. Driversmaintain the same position in the convoy; the vehiclesposition in the convoy is rotated uniformly.4.2 The test consists of a predetermined number of roadtesting cycles. Groove (void) depth measurements are madeafter completion of a specified number of

20、 test cycles.4.3 The wear rate may by calculated in a number of ways(see Practice F1016).5. Significance and Use5.1 The test data obtained with this test method may be usedto compare the performance of various tires for the conditionsunder which they were tested.5.2 This test method is suitable for

21、a variety of qualityassurance, research, and development purposes, when tires areto be compared during a single series of tests. The proceduredescribed may not be suitable for regulatory statutes orspecification acceptance because the values obtained may notagree, or correlate either in rank order o

22、r absolute tread wearperformance level, with values obtained on other roadsurfaces, or on the same surface after additional wear, underother environmental conditions, on other test vehicles, or withresults obtained by other test procedures.6. Interferences6.1 Vehicles of different types can influenc

23、e test results.When involved in comparison testing, avoid mixing of vehicleswith significantly different drivelines or suspensions.7. Apparatus7.1 Test VehicleAny vehicle compatible with test load andtire dimensions.7.2 Rims, of design rim width + 0.5, 0.0 in. for the test tireas recommended by the

24、Tire and Rim Association (T tire; tire groove depth loss; tire test; tripsheetASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the valid

25、ity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comme

26、nts are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have n

27、ot received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple co

28、pies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 08 (2014)4

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1