ASTM F779-1993(2006) Standard Test Method for Torsion Characteristic of Alpine Skis《高山滑雪板的扭转特性的测试方法》.pdf

1、Designation: F 779 93 (Reapproved 2006)Standard Test Method forTorsion Characteristic of Alpine Skis1This standard is issued under the fixed designation F 779; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revisi

2、on. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the measurement of ski fore-body torsion and ski afterbody torsion of adult Alpine skis.1.2 No limitatio

3、n to ski size is proposed. This test method isapplicable to all Alpine skis.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determi

4、ne the applica-bility of regulatory limitations prior to use.2. Terminology2.1 Definitions of Terms Specific to This Standard:2.1.1 afterbody torsion angle, uAthat angle, in degrees, towhich the running surface is rotated at Point A when a moment,Mt, is applied at Point A as shown in Fig. 1.2.1.2 af

5、terbody torsional spring constant, CAthe momentper degree of rotation of the ski afterbody when the ski isclamped in accordance with Fig. 1 and the moment applied inaccordance with Fig. 2.CAN m/deg!5MtuA2.1.3 forebody torsion angle, uFthat angle, in degrees, towhich the running surface is rotated at

6、 Point F when a moment,Mt, is applied at Point F as shown in Fig. 1.2.1.4 forebody torsional spring constant, CTSthe momentper degree of rotation of the ski forebody when the ski isclamped in accordance with Fig. 1 and the moment applied inaccordance with Fig. 2.CFN m/deg!5MtuF2.1.5 moment of torsio

7、n, Mtthe moment in newton-metresapplied to rotate the ski about its longitudinal axis when the skiis clamped according to Fig. 1 and the moment is appliedaccording to Fig. 2.3. Significance and Use3.1 This test method provides a means for determining thetorsional stiffness of Alpine skis. It is not

8、intended to evaluatethe data with regard to the quality of the ski.4. Apparatus4.1 Clamping Fixture, to grip the ski as a vise with a flat,rigid jaw and three clamps with at least 150 +50, 0 mmspacing between them. One clamp is located at each end of thefixture and one in the center as illustrated i

9、n Fig. 1. The clampsshould be at least 30 mm wide and cover the full width of theski.4.2 Torsion Head, shown in Fig. 2, with low-friction mo-ment (#0.2 Nm) and quasistatic loading system having aclamping fixture described in 4.1. Common devices for thisloading system are a weight on a cable wrapped

10、around thehead, or a weight on a lever arm rigidly attached to the head.The torsion head clamping fixture should have a width of 10 61 mm and a length equal to or greater than the width of the ski.The base surface of the torsion head fixture to the ski baseshould be in the same plane as the clamping

11、 fixture (that is,camber forced out of ski in clamped position).4.3 Scale, to measure the torsion angle with an accuracy of0.5.5. Procedure5.1 Test skis at room temperature (23 6 5C) withoutspecific preconditioning. Torsion head and clamping fixture areadjusted such that the distance between them is

12、 C/2 6 2mmshown in Fig. 1. Mount the ski to the clamping fixture so thatthe ski forebody or ski afterbody can rotate freely about PointM. The torsion head is attached to the ski at Point A or F 6 2mm such that the longitudinal axis of the ski is in the center ofthe torsion head. Apply a moment, Mt,o

13、f206 0.2 Nm. (Themoment should be applied quasistatically.) The torsion anglemust be read within 2 to 5 s after the torsion moment, Mt,isinitially applied.6. Calculation6.1 Calculate the afterbody torsional spring constant, CA,innewton-metres per degree, in accordance with the followingequation:1Thi

14、s test method is under the jurisdiction of ASTM Committee F27 on SnowSkiing and is the direct responsibility of F27.30 on Skis and Boots.Current edition approved Oct. 1, 2006. Published December 2006. Originallyapproved in 1982. Last previous edition approved in 1998 as F 779 93 (1998).1Copyright AS

15、TM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.CA5MtuA(1)6.2 Calculate the forebody torsional spring constant, CF,innewton-metres per degree, in accordance with the followingequation:CF5MtuB(2)7. Report7.1 Report the following information:7.1.1

16、Brand, model designation, manufacturers serial num-ber of ski, and size of ski,7.1.2 Afterbody torsional spring constant, forebody tor-sional spring constant,7.1.3 Any deviations from this standard with explanations,and7.1.4 ASTM F 779.8. Precision and Bias8.1 PrecisionThe precision of this test met

17、hod is currentlybeing determined.8.2 BiasThe procedure in this test method has no biasbecause the values for torsion characteristics of Alpine skis aredefined only in terms of the test method.9. Keywords9.1 Alpine skis; torsion characteristicsFIG. 1 Clamping FixtureFIG. 2 Torsion Head FixtureF 779 9

18、3 (2006)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such ri

19、ghts, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additiona

20、l standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the AST

21、M Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 779 93 (2006)3