ASTM F823-1993(2004) Standard Specification for Desk Log Marine Steel with Cabinet《船用木制有钢柜的办公桌》.pdf

1、Designation: F 823 93 (Reapproved 2004)An American National StandardStandard Specification forDesk, Log, Marine, Steel, with Cabinet1This standard is issued under the fixed designation F 823; the number immediately following the designation indicates the year oforiginal adoption or, in the case of r

2、evision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the construction of marine logdesks of steel construction with cabinet

3、s.1.2 Values stated in inch-pound units are to be regarded asthe standard. The metric equivalents, given in parentheses, areprovided for information only.2. Referenced Documents2.1 ASTM Standards:2A 366/A 366M Specification for Commercial Steel (CS)Sheet, Carbon, (0.15 Maximum Percent) Cold-Rolled3D

4、 907 Terminology of AdhesivesF 782 Specification for Doors, Furniture, MarineF 825 Specification for Drawers, Furniture, Marine, SteelF 826 Specification for Tops, Furniture, Marine, Steel2.2 American Institute of Steel Construction Manual:AISC Wire and Sheet Metal Gages Equivalent Thicknessin Decim

5、als of an Inch, U.S. Standard Gage for UncoatedHot and Cold Rolled Sheets43. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 log desk with cabineta desk with attached cabinetlocated in various places aboard ship for making records andfor storage. Log desk has a drawer with a writ

6、ing surface at thetop and a cabinet with adjustable shelves and doors below.4. Ordering Information4.1 Orders for items purchased under this specification shallinclude the following information:4.1.1 Quantity.4.1.2 Paint:4.1.2.1 ColorPurchaser shall pick from manufacturerssamples or submit sample ch

7、ip of color desired.4.1.2.2 Manufacturers standard baked enamel will be fur-nished unless otherwise required and indicated by the pur-chaser.4.1.3 Options for Tops:4.1.3.1 Unless otherwise specified in the ordering docu-ments, the top supplied by the furniture manufacturer may be,at his option, Type

8、 I, II, III, or IV in accordance withSpecification F 826.4.1.3.2 Color or pattern of top covering material shall bespecified.4.1.4 Options for DrawersDrawer locks shall be fur-nished only when specified in ordering documents. Masterkeying of drawer locks will not be provided unless requiredand defin

9、ed by the ordering documents. See SpecificationF 825 for lock description.4.1.5 Options for DoorsDoor locks shall be furnishedonly when specified in ordering documents. Master keying ofdoor locks will not be provided unless required and defined inthe ordering documents. Doors shall be Type I in acco

10、rdancewith Specification F 782.4.1.6 If the total weight of the chest of drawers is requiredit shall be requested by the purchaser.5. Materials and Manufacture5.1 For typical design, see Fig. 1.5.2 Sheet metal shall be in accordance with SpecificationA 366/A 366M, commercial quality.5.2.1 Minimum sh

11、eet metal thickness shall be:5.2.1.1 Sides and front rails 18 USSG (0.0478 in. or 1.2mm).5.2.1.2 Back 20 USSG (0.0359 in. or 0.9 mm).5.2.1.3 Base frame 16 USSG (0.0598 in. or 1.5 mm).5.3 Joining of Metal Components:5.3.1 Metal components shall be joined by welding orgluing with a structural adhesive

12、 as defined in TerminologyD 907. The back panel may be riveted to case provided rivetsare not visible after installation.5.3.2 Joining shall be adequate to prevent racking of chestduring handling.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is

13、 the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved Nov. 1, 2004. Published November 2004. Originallyapproved in 1983. Last previous edition approved in 1999 as F 823 93 (1999).2For referenced ASTM standards, visit the ASTM website, www.astm.org

14、, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.4Available from the American Institute of Steel Construction, One E. WackerDr., Chicago, IL 606012001.1Copyright ASTM

15、International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.3.3 Spotwelds shall be spaced approximately 3 in. (76mm) on centers.5.3.4 Visible spotwelds, higher than the general surface ofthe adjacent metal, shall be ground flush.5.3.5 Visible spotweld depress

16、ions shall be spot filled andsanded flush.5.4 Side panels shall be stiffened suitably to prevent buck-ling or oil-canning.5.5 Sound deadening shall be vermin proof and applied toback and inner face of sides of chest. Location and thickness ofapplied sound deadener shall be as required to sound-deade

17、nchest.5.6 Top shall be manufactured in accordance with Specifi-cation F 826.5.7 Drawers shall be manufactured in accordance withSpecification F 825.5.8 Doors shall be Type I, Grade A and shall be manufac-tured in accordance with Specification F 782.5.9 Cabinet section shall be provided with two adj

18、ustableshelves.5.10 Top shall be provided with a pencil tray along backedge.5.11 A furniture base shall be provided suitable for securinglog desk to deck.6. Performance Requirements6.1 The completed log desk with cabinet, with top, drawers,and doors installed, shall satisfy the corresponding perfor-

19、mance requirements outlined in Specifications F 826, F 825,and F 782.7. Dimensions7.1 For dimensions, see Table 1.8. Workmanship, Finish, and Quality Assurance8.1 All workmanship and material shall be of specifiedquality in keeping with the best commercial marine practice soas to produce each item s

20、uitable for its intended use.8.2 All exposed burrs, raw or sharp edges which might beinjurious to personnel shall be removed.8.3 Depressions considered unacceptable for products enduse shall be spot filled and sanded smooth.8.4 Finish:8.4.1 All steel surfaces unless corrosion resistant or with acorr

21、osion-resistant plating shall be painted so as to preventcorrosion.8.4.2 Unless otherwise required by the ordering documents,all parts normally visible on the completed unit shall have themanufacturers standard baked-on enamel finish.8.4.3 Color to be specified in the ordering documents.NOTE 1For de

22、scription of Type I, II, III, and IV tops, see Specification F 826.NOTE 2For description of drawers, see Specification F 825.NOTE 3For description of Type I doors and available alternates, see Specification F 782.NOTE 4If log desk is located in a corner, Dimension “F” next to this adjacent wall shal

23、l be 0 in. (0 mm). In all other cases, the minimum value forDimension “F” shall be34 in. (19.05 mm).NOTE 5The minimum value for Dimension “H” shall be 4 in. (102 mm).FIG. 1 Log Desk with CabinetF 823 93 (2004)29. Inspection and Certification9.1 Manufacturer shall inspect and certify that the item of

24、furniture complies with the furniture specification and theloading requirements as defined in Section 6.10. Packaging and Package Marking10.1 Each item shall be marked in accordance with thepurchase order.10.2 Packaging shall be provided and shall be acceptable toa common carrier.11. Keywords11.1 ca

25、binets; log desks; marine furniture; marine log desks;steel log desksASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of an

26、y such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are i

27、nvited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not receiv

28、ed a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of

29、this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Dimensions of Log Desk with CabinetDesignationin. mmDimension Tolerance To + Or Dimension Tolerance To +

30、 Or Width A 30116 762 2Height B 42116 1067 2Depth C 24116 610 2Drawer section overhang D 558116 143 2Toespace, front, E 3 max116 76 max 2Toespace, side,AF 4 max116 102 max 2Drawer section height G 7 max116 178 max 2Base heightBH 434 max116 121 max 2AIf log desk is located in a corner, Dimension F next to this adjacent wall shall be 0 in. (0 mm). In all other cases, the minimum value for Dimension F shall be34 in.(19 mm).BThe minimum value for Dimension H shall be 4 in. (120 mm).F 823 93 (2004)3