ASTM F837M-2002a(2015) Standard Specification for Stainless Steel Socket Head Cap Screws [Metric]《不锈钢内六角螺钉的标准规格 (米制)》.pdf

1、Designation: F837M 02a (Reapproved 2015)Standard Specification forStainless Steel Socket Head Cap Screws Metric1This standard is issued under the fixed designation F837M; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of

2、last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the chemical and mechanicalrequirements for stainless steel metric socket head cap screws(SH

3、CS) with nominal thread M1.6 through M36 and intendedfor use in applications requiring general corrosion resistance.1.2 Two groups of stainless steel alloys are covered, auste-nitic Grade A1 and martensitic Grade C1.1.3 Four property classes are covered: austenitic A1-50 inan annealed condition at 5

4、85 MPa maximum; austeniticA155in a cold worked condition at 550 MPa minimum; austeniticA1-70 in a cold worked condition at 700 MPa minimum, andmartensitic C1-110 in a heat treated condition at 1100 MPaminimum.1.4 The values stated in SI units are to be regarded asstandard. No other units of measurem

5、ent are included in thisstandard.1.5 This hazard statement pertains only to Section 13, TestMethods: This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health

6、practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2A262 Practices for Detecting Susceptibility to IntergranularAttack in Austenitic Stainless SteelsA342/A342M Test Methods for Permeability of WeaklyMagnetic MaterialsA380 Pract

7、ice for Cleaning, Descaling, and Passivation ofStainless Steel Parts, Equipment, and SystemsA751 Test Methods, Practices, and Terminology for Chemi-cal Analysis of Steel ProductsA967 Specification for Chemical Passivation Treatments forStainless Steel PartsD3951 Practice for Commercial PackagingE18

8、Test Methods for Rockwell Hardness of Metallic Ma-terialsE92 Test Method for Vickers Hardness of Metallic Materials(Withdrawn 2010)3E384 Test Method for Knoop and Vickers Hardness ofMaterialsF606M Test Methods for Determining the Mechanical Prop-erties of Externally and Internally Threaded Fasteners

9、,Washers, and Rivets (Metric)F738M Specification for Stainless Steel Metric Bolts,Screws, and Studs (Withdrawn 2014)3F1470 Practice for Fastener Sampling for Specified Me-chanical Properties and Performance Inspection2.2 ASME Standard:ASME B 18.3.1M Socket Head Cap Screws (Metric Series)43. Classifi

10、cation3.1 The designation of the property class for the twomaterials and conditions of this specification shall be consistentwith the stainless steel designations in Specification F738M.3.2 The austenitic stainless steel socket head cap screw shallbe designated F837MA1-50, F837MA1-55, or F837MA1-70.

11、3.3 The martensitic stainless steel socket head cap screwshall be designated F837M C1-110.4. Ordering Information4.1 Orders for socket head cap screws under this specifica-tion shall include:4.1.1 Quantity (number of pieces of each item),4.1.2 Name of the item (socket head cap screws, SHCS),4.1.3 Si

12、ze (nominal diameter, thread pitch, thread class,screw length) or part number,4.1.4 Property class (A1-50, A155, A1-70, or C1-110),4.1.5 ASTM specification and date of issue. When date ofissue is not specified, fasteners shall be furnished to the latestissue,1This specification is under the jurisdic

13、tion of ASTM Committee F16 onFasteners and is the direct responsibility of Subcommittee F16.04 on NonferrousFasteners.Current edition approved Sept. 1, 2015. Published November 2015. Originallypublished as F837M 83. Last previous edition approved in 2010 asF837M 02a(2010). DOI: 10.1520/F0837M-02AR15

14、.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is re

15、ferenced onwww.astm.org.4Available from Global Engineering Documents, 15 Inverness Way, EastEnglewood, CO 80112-5704, http:/.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.1.6 Supplementary requirements, if any (see S1 throughS3),4

16、.1.7 Additional special requirements, if any, to be specifiedon the purchase order:4.1.7.1 Forming (see 5.1),4.1.7.2 Threading (see 5.2),4.1.7.3 Surface finish (see 11.1),4.1.7.4 Alloy selection (see 7.2),4.1.7.5 Test report (see 11.2),4.1.7.6 Additional testing (see section 12.3),4.1.7.7 Inspection

17、 (see 13.1),4.1.7.8 Rejection (see 14.1), and4.1.7.9 Certification (see 15.1).4.1.7.10 Special packaging requirements (see section18.1.2).5. Material and Manufacture5.1 ForgingUnless otherwise specified, screws in sizesM3 through M20 with lengths up to 10 times the nominalproduct diameter or 150 mm,

18、 whichever is shorter, shall becold headed except that they may be hot headed or machinedby agreement with the purchaser. Larger sizes and lengths maybe cold or hot headed. Screws smaller and larger than the M3through M36 range may be machined. Sockets may be forgedor machined at the option of the m

19、anufacturer.5.2 ThreadsUnless otherwise specified, screws in sizes upto M24 inclusive and product lengths up to 150 mm inclusiveshall have threads formed by rolling, except by special agree-ment with the purchaser. Larger products may be rolled, cut, orground at the option of the manufacturer.6. Hea

20、t Treatment6.1 Austenitic alloys class A1-50 screws, followingmanufacture, shall be annealed by heating to 1040 6 30C toobtain maximum corrosion resistance and minimum perme-ability. The screws shall be held for a sufficient time attemperature and then cooled at a rate sufficient to preventprecipita

21、tion of the carbide and to provide the propertiesspecified in Table 1.6.2 When Condition A1-55 or A1-70 is specified, theaustenitic alloys shall be annealed as specified in 6.1 generallyby the raw material manufacturer, then cold worked to developspecific properties.6.3 Martensitic alloy Class C1 11

22、0 screws shall be hardenedand tempered by heating to 1010 6 30C sufficient foraustenitization, holding for at least12 h, rapid air or oilquenching, reheating to 275C minimum and holding for atleast 1 h and then air cooling to provide the properties specifiedin Table 1.7. Chemical Composition7.1 It i

23、s the intent of this specification that screws shall beordered by property class. The chemical composition of thescrew material shall conform to the requirements of Table 2.7.2 Unless otherwise specified in the inquiry and purchaseorder (see Supplementary Requirement S2) when A1-50,A1-55, orA1-70 pr

24、operty class is specified, the choice of alloyused by the manufacturer shall be clearly identified on allcertification required in the purchase order The chemicalcomposition shall conform to the limits specified in Table 2.7.3 When chemical analysis is performed by the purchaserusing finished fasten

25、ers representing each lot, the chemicalcontents obtained shall conform to the limits specified in Table2 for the specific alloy. Chemical contents shall conform to thetolerances specified in Specification A751.7.3.1 In the event of discrepancy, a referee analysis asspecified in 13.1 of samples for e

26、ach lot shall be made inaccordance with 12.3.1.1.8. Mechanical Properties8.1 Screws shall be tested in accordance with the mechani-cal testing requirements for the property class, nominal threaddiameter, length, and specified minimum tensile strength asspecified in Table 3 and shall meet the mechani

27、cal require-ments specified for that product in Table 1.8.2 For products on which both hardness and tension testsare performed, acceptance based on tensile requirements shalltake precedence over low hardness readings (see Table 4).9. Corrosion Resistance9.1 Carbide Precipitation:9.1.1 Rod, bar, and

28、wire in the austenitic alloy group A1(not including the free-machining grade 303) used to makefasteners in accordance with this specification shall be capableof passing the test for susceptibility to intergranular corrosionas specified in Practice E of Practices A262.TABLE 1 Mechanical Property Requ

29、irementsProperty ClassNominalThreadDiameterAFull Size Product Tests Machined Specimen Tests Core HardnessBTensile Strength,MPaMinimumExtensionCTensileStrength,MPaYieldStrength,MPaElon-gation,%Vickers RockwellA150 M1.6 to M36 585 max 0.6D 585 max 380 max 40 210 max 95 HRB maxA1-55 M1.6 to M20 550 min

30、 0.4D 550 min 270 min 25 160 min 50 HRA minA170 M1.6 to M20 700 min 0.4D 600 min 450 min 20 220 min 59 HRA minC1-110 M1.6 to M5 1100 . . . . . . . . . . . . 350440 3645 HRCM6 to M36 1100 0.2 D 1100 820 12 350440 3645 HRCAFor A155 and A170 property class fasteners with nominal thread diameter larger

31、than M20, the mechanical properties shall be agreed upon between the user andmanufacturer.BCore hardness is only required when full-size product tensile testing cannot be accomplished.CD denotes nominal thread size.F837M 02a (2015)29.1.2 As stated in Practices A262, samples may be subjectedto the fa

32、ster and more severe screening test in accordance withPractice A. Failing Practice A, specimens shall be tested toPractice E and be considered satisfactory if passing Practice E.10. Dimensions10.1 Unless otherwise specified, the products shall conformto the requirements ofASME B18.3.1M Hexagon Socke

33、t HeadCap Screws (Metric Series).11. Workmanship, Finish, and Appearance11.1 Surface TreatmentUnless otherwise specified, screwsshall be cleaned, descaled and passivated in accordance withPractice A380 or Specification A967 at the option of themanufacturer.11.2 The surface discontinuities for these

34、products shallconform to Specification F1470 and the additional limitationsspecified herein.11.2.1 Forging defects that connect the socket to the periph-ery of the head are not permissible. Defects originating on theperiphery and with a traverse indicating a potential to intersectare not permissible

35、. Other forging defects are permissibleprovided those located in the bearing area, fillet, and topsurfaces shall not have a depth exceeding 0.03 D or 0.13 m,whichever is greater. For peripheral discontinuities, the maxi-mum depth may be 0.06 D (see Fig. 1).11.2.2 Forging defects located in the socke

36、t wall within 0.1times the actual key engagement, T, from the bottom of thesocket are not permissible. Discontinuities located elsewhere inthe socket shall not have a length exceeding 0.25 T,oramaximum depth of 0.03 D not to exceed 0.13 mm (see Fig. 2).11.2.3 Seams in the shank shall not exceed a de

37、pth of 0.03D or 0.2 mm, whichever is greater.11.2.4 No transverse discontinuities shall be permitted inthe head-to-shank fillet area.11.2.5 Threads shall have no laps at the root or on the flanks,as shown in Fig. 3. Laps are permitted at the crests (Fig. 3c)that do not exceed 25 % of the basic threa

38、d depth, and on theflanks outside the pitch cylinder. Longitudinal seams rolledbeneath the root of the thread and across the crests of cutthreads are acceptable within the limits of 11.2.3.12. Number of Tests12.1 The requirements of this specification shall be met incontinuous mass production for st

39、ock and the manufacturershall make sample inspections to ensure that the productconforms to the specified requirements. Additional tests ofindividual shipments of fasteners are not ordinarily necessary.A record of the individual heat of steel in each lot shall bemaintained. The containers shall be c

40、oded to permit identifi-cation of the lot.12.2 When specified in the purchase order, the manufacturershall furnish a test report of the last complete set of chemicalanalysis and mechanical tests for each stock size in eachshipment.12.3 When tests of individual shipments are required,Supplementary Re

41、quirement S1 must be specified in theinquiry and order.TABLE 2 Chemical RequirementsPropertyClassUNSDesignation AlloyComposition, % maximum except as shownCarbon Manganese Phosphorus Sulfur Silicon Chromium Nickel Copper MolybdenumAustenitic AlloysA1 S30300 303A0.15 2.00 0.20 0.15 min 1.00 17.0 to 1

42、9.0 8.0 to 10.0 . . . 0.60 maxBA1 S30400 304 0.08 2.00 0.045 0.030 1.00 18.0 to 20.0 8.0 to 10.5 1.00 . . .A1 S30403 304L 0.030 2.00 0.045 0.030 1.00 18.0 to 20.0 8.0 to 12.0 1.00 . . .A1 S30500 305 0.12 2.00 0.045 0.030 1.00 17.0 to 19.0 10.5 to 13.0 1.00 . . .A1 S38400 384 0.08 2.00 0.045 0.030 1.

43、00 15.0 to 17.0 17.0 to 19.0 . . . . . .A1 S20300 XM1A0.08 5.0 to 6.5 0.040 0.18 to 0.35 1.00 16.0 to 18.0 5.0 to 6.5 1.75 to 2.25 0.50 maxBA1 S30430 189LW 0.10 2.00 0.045 0.030 1.00 17.0 to 19.0 8.0 to 10.0 3.00 to 4.00 . . .A1 S30433 302HQ 0.03 2.00 0.045 0.030 1.00 17.0 to 19.0 8.0 to 10.0 3.0 to

44、 4.0 . . .A1 S31600 316 0.08 2.00 0.045 0.030 1.00 16.0 to 18.0 10.0 to 14.0 . . . 2.0 to 3.0A1 S31603 316L 0.03 2.00 0.045 0.030 1.00 16.0 to 18.0 10.0 to 14.0 . . . 2.0 to 3.0Martensitic AlloysC1 S4100 410 0.15 1.00 0.040 0.030 1.00 11.5 to 13.5 . . . . . . . . .AFree machining grades are not reco

45、mmended for forged product. These grades may be furnished only when approved by the purchaser.BAt manufacturers option, determined only when intentionally added.TABLE 3 Mechanical Testing RequirementsItem Product LengthHardnessTest conducted Using Full SizeProductTest Conducted Using Machined Test S

46、pecificationmax minExten-sionAxial TensileStrengthYield Strength0.2 % offsetTensileStrengthElonga-tion1 #3 DABB. . . . .23D to 300 mmB.BB. . .3 Over 300 mmB. A A B B BAD denotes nominal diameter of product.BDenotes mandatory test. In addition, either all tests denoted by A or all tests denoted by B

47、shall be performed. In case of arbitration, full-size tests, denoted A, shall bedecisive.F837M 02a (2015)312.3.1 When the purchaser does not specify the samplingplan and basis of acceptance, the following shall apply:12.3.1.1 The lot, for purposes of selecting samples, shallconsist of all products o

48、ffered for inspection and testing, at onetime, that are the same type, style, nominal diameter, threadpitch, nominal length, material (alloy), property class, andsurface finish.12.3.1.2 From each lot, samples shall be selected at randomand tested for each requirement in accordance with thefollowing

49、plan:Number of Pieces in LotNumber ofSamples800 and less 1Over 800 to 8000, incl 2Over 8000 to 22 000, incl 3Over 22 000 512.3.1.3 Should any sample fail to meet the requirements ofa specified test, double the number of samples from the samelot shall be retested for the requirement(s) in which it failed.All of the additional samples shall conform to the specificationor the lot shall be rejected.12.3.1.4 If the failure of a test specimen is due to improperpreparation of the specimen or an incorrect testing technique,the specimen shall be di