1、Designation: F 941 99 (Reapproved 2005)An American National StandardStandard Practice forInspection of Marine Surface Preparation and CoatingApplication1This standard is issued under the fixed designation F 941; the number immediately following the designation indicates the year oforiginal adoption
2、or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scop
3、e1.1 This practice is intended to serve as a guide fordetermining specific inspection requirements for marine sur-face preparation and coating application during new construc-tion, major retrofit, or routine maintenance contracts.1.2 It is intended that this practice be used to coordinateinspection
4、activities between ship owner, ship builder, coatingsmanufacturer and coatings applicator, and that specific require-ments be developed before the commencement of surfacepreparation or coating application, or both.1.3 This practice does not provide a means of recordingrequired data (for example, fil
5、m thicknesses, temperatures,relative humidity, and so forth), but instead establishes a formatfor deciding what data must be recorded, when during thepreparation/coating process, and by whom.1.4 This practice does not establish accept/reject criteria forsurface preparation or coating inspection, nor
6、 does it addressmethods of repairing deficiencies found. It does, however,provide a means of determining them.1.5 This standard may involve hazardous materials, opera-tions, and equipment. This standard does not purport toaddress all of the safety concerns, if any, associated with itsuse. It is the
7、responsibility of the user of this standard toestablish appropriate safety and health practices and deter-mine the applicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 3276 Guide for Painting Inspectors (Metal Substrates)D 4940 Test Method for Conductimet
8、ric Analysis of WaterSoluble Ionic Contamination of Blasting AbrasivesF 718 Standard for Shipbuilders and Marine Paints andCoatings Product/Procedure Data Sheet2.2 SSPC Standards:3SSPC PA 2 Measurement of Film ThicknessSSPC-SP 1 Solvent CleaningSSPC-SP 3 Power Tool CleaningSSPC-SP 5 White Metal Blas
9、t CleaningSSPC-SP 6 Commercial Blast CleaningSSPC-SP 7 Brush-Off Blast CleaningSSPC-SP 10 Near-White Blast CleaningSSPC VIS-1 Pictorial Surface Preparation Standards forPainting Steel Surfaces2.3 JSRA Standard:4SPSS Standard for the Preparation of Steel Surface Prior toPainting2.4 ISO Standards:5ISO
10、 8501-1:1988 Preparation of Substrates Before Applica-tion of Paints and Related ProductsVisual Assessmentof Surface CleanlinessISO 8502-1:1991 Preparation of Substrates Before Applica-tions of Paints and Related ProductsTests for Assess-ment of Surface Cleanliness: Soluble Iron ProductsISO 8502-2:1
11、992 Preparation of Substrates Before Applica-tions of Paints and Related ProductsTests for theAssessment of Surface CleanlinessLaboratory Determi-nation of Chloride on Cleaned SurfacesISO 8502-3:1992 Preparation of Substrates Before Applica-tions of Paints and Related ProductsTests for theAssessment
12、 of Surface CleanlinessAssessment of Duston Steel Surfaces Prepared for Painting (Pressure Sensi-tive Tape Method)ISO 8502-4:1993 Preparation of Substrates Before Applica-tions of Paints and Related ProductsTests for theAssessment of Surface CleanlinessGuidance on Estima-tion of the Probability of C
13、ondensation Prior to PaintApplicationISO 8502-6 Preparation of Substrates Before Applications1This practice is under the jurisdiction of ASTM Committee F25 on Ships andMarine Technology and is the direct responsibility of Subcommittee F25.01 onStructures.Current edition approved May 1, 2005. Publish
14、ed May 2005. Originallyapproved in 1985. Last previous edition approved in 1999 as F 941 99.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document S
15、ummary page onthe ASTM website.3Available from Society for Protective Coatings (SSPC), 40 24th St., 6th Floor,Pittsburgh, PA 15222-4656.4JSRA standards are available from Shipbuilding Research Assoc. of Japan,Sempakushinko Bldg., 15-16 1-Chome Toranomon Minato-Ku, Tokyo 105.5Available from American
16、National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.of Paints and Related ProductsTests for the Assessmentof Surface CleanlinessField Extraction of Water S
17、olubleSalts (Dr. Bresle Method)ISO 8502-9 Preparation of Substrates Before Applicationsof Paints and Related ProductsTests for the Assessmentof Surface CleanlinessField Evaluation of WaterSoluble Salts by Conductimetric EvaluationISO 8503-1:1988 Preparation of Substrates Before Applica-tion of Paint
18、s and Related ProductsSurface RoughnessCharacteristics of Blast-Cleaned Steel SubstratesComparator ProcedureISO 8503-2:1988 Preparation of Substrates Before Applica-tion of Paints and Related ProductsSurface RoughnessCharacteristics of Blast-Cleaned Steel SubstratesMethod for the Calibration of ISO
19、Surface Profile Com-parators and for the Determination of Surface ProfileFocusing Microscope ProcedureISO 8503-4:1988 Preparation of Substrates Before Applica-tion of Paints and Related ProductsSurface RoughnessCharacteristics of Blast-Cleaned Steel SubstratesMethod for the Calibration of ISO Surfac
20、e Profile Com-parators and for the Determination of Surface ProfileStylus Instrument ProcedureISO 8504-1:1992 Preparation of Substrates Before Applica-tion of Paints and Related ProductsSurface PreparationMethodsGeneral GuidelinesISO 8504-2:1992 Preparation of Substrates Before Applica-tion of Paint
21、s and Related ProductsSurface PreparationMethodsAbrasive-Blast CleaningISO 8504-3:1993 Preparation of Substrates Before Applica-tion of Paints and Related ProductsSurface PreparationMethodsHand and Power Tool Cleaning2.5 ASTM Adjuncts:Sample Form for Determining Marine Surface Preparationand Coating
22、 Application Inspection Practices (F 941)63. Significance and Use3.1 This practice may be invoked by any of the partiesmentioned in 1.2 and may be included as part of a specificationor used to clarify or reinforce an existing specification that doesnot adequately address inspection. When invoked by
23、the shipowner on the shipbuilder, the shipbuilder is responsible for thecoordination effort.3.2 As surface preparation and coating requirements gener-ally differ from ship area to ship area, this practice shall beapplied separately to those areas of similar requirements.3.3 The contents of this prac
24、tice shall be addressed (for eachapplicable ship area) at a prestartup meeting attended by theparties mentioned in 1.2.4. Procedures4.1 At the beginning of each new contract, after finalprotective coatings selection, but well before the start of anysurface preparation or coating application, a meeti
25、ng shall beheld between those parties mentioned in 1.2. The Sample Formfor Determining Marine Surface Preparation and CoatingApplication Inspection Practices6shall be completed (for eachseparate ship area) by the responsible party prior to and eachitem discussed and agreed upon during the meeting. T
26、heselected coating supplier(s) shall make available at this timespecific product data sheets in accordance with Standard F 718harmonizing with the design intent of the application for eachcoating specified.4.2 After completion of the sample form6and after requireddocumentation has been submitted by
27、the coatings supplier(s),signatures of applicable parties shall be obtained and dated.4.3 A means of collecting and recording the informationrequired by the sample form shall be developed (see 5.1.6.4).5. Report5.1 The following paragraphs coincide with the individualsections of the sample form to a
28、id in their proper completion.Guide D 3276 shall be consulted for additional guidance ongeneral surface preparation and coating inspection practices.5.1.1 ContractIndicate name of vessel, present owner/agent, and type of vessel (for example, roll-on/roll-off, tanker,and so forth).5.1.2 CategoryIndic
29、ate whether contract is a new con-struction, major retrofit, or routine maintenance contract.5.1.3 Ship Area(s) ConcernedIndicate the ship area(s)(for example, underwater hull, ballast tanks, and so forth) thatare being addressed in the inspection practice. Where appro-priate, frame numbers or ship
30、levels, or both, shall be included.5.1.4 Surface Preparation Requirements:5.1.4.1 Surface Preparation, InitialIndicate the stan-dard(s) that will be used to govern the initial surface prepara-tion process, for the particular ship area(s) under consideration.Both written and visual standards shall be
31、 used (ISO, JSRA,NACE, or SSPC as appropriate).75.1.4.2 Surface Preparation, Touch-UpIndicate the sur-face preparation that will be used for repair of small areas ofcoating damage or areas, or both, left free of coatings (forexample, erection butts) during construction.5.1.4.3 AbrasiveAs a minimum,
32、indicate the type and sizeof the abrasive that will be used to perform the surfacepreparation process. Any other data (minimum hardness, mois-ture content, salt content as per Test Method D 4940, and soforth) considered pertinent shall also be considered.5.1.4.4 Surface ProfileIndicate any requireme
33、nts for sur-face profile (after preparation), and the method that will beused to perform the measurements.5.1.4.5 Surface ImperfectionsSpecific requirements forrepair or removal of surface imperfections, or both, if notadequately addressed or defined in the applicable surfacepreparation standard, sh
34、all be included in this section. Theseimperfections include weld spatter, weld porosities, lamina-tions, sharp edges, and pits.6Available from ASTM International Headquarters. Order Adjunct No.ADJ0941.7SNAME Bulletin 4-9, available from The Society of Naval Architects andMarine Engineers, 601 Pavoni
35、a Ave., Jersey City, NJ 07306, may also be used as anadditional reference. This document shall be used as a guide only and is not to beused as a standard.F 941 99 (2005)25.1.4.6 Cleaning Between CoatsIndicate allowable meth-ods for removal of contaminants from the surface of the primeror intermediat
36、e coats before overcoating.5.1.5 Coating Requirements:5.1.5.1 Specification, InitialIndicate the complete coatingsystem specified to be applied to the ship area(s) underconsideration. Include the manufacturers name, product des-ignation or specification number, required color, and requireddry film t
37、hickness per coat.5.1.5.2 Specification, Touch-UpIndicate the coating sys-tem (if different from the initial system) that will be used torepair areas of coating damage or areas left uncoated, or both,during construction. Include the manufacturers name, productdesignation or specification number, req
38、uired color, and dryfilm thickness per coat.5.1.5.3 Application ParametersStandard F 718 productdata sheet shall be completed by the coatings manufacturer foreach product specified; these data sheets shall be used toestablish specific parameters such as minimum/maximum ap-plication temperatures and
39、recoat times, mixing procedures,measurement of wet/dry film thickness, and so forth. Com-pleted data sheets shall be attached to the applicable inspectionpractice before obtaining approval signatures. The manufactur-ers Material Safety Data Sheets shall be obtained for eachproduct and similarly atta
40、ched.5.1.5.4 Stripe CoatsIndicate where stripe coats are re-quired, when applied, what coating should be used, and theallowable method(s) of application.5.1.6 Inspections:5.1.6.1 Timing and FrequencyIndicate when inspectionswill occur during the surface preparation and coating applica-tion processes
41、, and their frequency (per unit surface area).5.1.6.2 ResponsibilitiesIndicate all persons (name, em-ployer, position, telephone number) that must be present at thetime of inspection, and a procedure to follow in the event oftheir absence or delay.5.1.6.3 Notification ProcedureDevelop a procedurewhi
42、ch establishes a specific method for notifying all respon-sible parties that a ship area is ready for inspection.5.1.6.4 Record KeepingIndicate what will be recorded ateach inspection, who will accomplish the recording, how theinformation will be recorded, and to whom copies should besent.Aform shal
43、l be developed to aid in this recording process.Space shall be provided for approval or disapproval of thesurface preparation or coating application, for noting excep-tions found and correction of discrepancies, and for final“ signoff” of the completed ship area under consideration.5.1.7 Sequencing
44、of WorkIndicate the general order ofaccomplishment of the specified surface preparation and coat-ing work, and any additional information that might aid inassuring a smooth flow of this work.5.1.8 ApprovalsSignatures shall be obtained from allresponsible parties after a thorough review of the comple
45、tedinspection practice (see Sample Form for Determining MarineSurface Preparation and Coating Application Inspection Prac-tices6and all attached documentation).6. Keywords6.1 coating application; inspection requirements; marinesurface preparationASTM International takes no position respecting the va
46、lidity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is su
47、bject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headqu
48、arters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This stand
49、ard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 941 99 (2005)3
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1