ASTM F2135-2001(2012) Standard Specification for Molded Drain Waste and Vent (DWV) Short-Pattern Plastic Fittings《模制排水 污物和通风的短型塑料配件的标准规格》.pdf

1、Designation: F2135 01 (Reapproved 2012)An American National StandardStandard Specification forMolded Drain, Waste, and Vent (DWV) Short-Pattern PlasticFittings1This standard is issued under the fixed designation F2135; the number immediately following the designation indicates the year oforiginal ad

2、option or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers standard fitting geometries formolded short-

3、pattern plastic fittings intended for use in drain,waste, and vent applications.1.2 Fittings meeting the requirements of this specificationare designed for use with outside-diameter controlled pipe. Thebody inside diameter can vary significantly as the wall thick-ness and outside diameter varies, an

4、d therefore, is not suitablefor use as a fitting socket.1.3 Fittings meeting the requirements of this specificationshall be tested in accordance with the applicable requirementsof Specifications D2661 or D2665.1.4 The values stated in inch-pound units are to be regardedas standard. The values given

5、in parentheses are mathematicalconversions to SI units which are provided for informationonly and are not considered standard.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish ap

6、pro-priate safety and health practices and determine the applica-bility of regulatory requirements prior to use.2. Referenced Documents2.1 ASTM Standards:2D2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2661 Specification for Acrylonitrile-Butadiene-Styrene(ABS) Sche

7、dule 40 Plastic Drain, Waste, and Vent Pipeand FittingsD2665 Specification for Poly(Vinyl Chloride) (PVC) PlasticDrain, Waste, and Vent Pipe and FittingsD2749 Symbols for Dimensions of Plastic Pipe FittingsF1498 Specification for Taper Pipe Threads 60 for Ther-moplastic Pipe and Fittings3. Requireme

8、nts3.1 Short-pattern fittings shall conform to the geometries asspecified in this specification.3.2 All other dimensions shall be determined in accordancewith Test Method D2122.3.3 The exact outside shape of a short-pattern fitting isdetermined by the socket dimensions, wall thickness require-ments,

9、 waterway, and any other critical dimensions that may bespecified.3.4 Configurations designed as short as possible are accept-able providing that the minimum wall thickness requirementsfor the particular nominal size being made is followed.3.5 All short-pattern fittings used for drainage and having

10、a90 directional change (except vent fittings) shall have a pitchof14 in./ft or 1128.3.6 All short-pattern fittings having tapered threads shallconform and be gaged in accordance with Specification F1498.3.7 45 Y-Branches:3.7.1 Short-pattern 45 Y-branches shall not be pitched.3.7.1.1 When the branch

11、of a short-pattern 45 Y is of asmaller diameter than the main body of the fitting, the internaldiameters of the fitting shall remain constant until theyintercept one another.3.8 One-Quarter Bends:3.8.1 Short-pattern one-quarter bends shall have a centerlineradius of curvature of not less than the no

12、minal pipe size, withthe exception of traps. The centerline radius of curvature shallbe measured in accordance with Section 4.3.9 Sanitary Tees:3.9.1 Short-pattern sanitary tees and reducing tees shallhave a centerline radius of curvature on the side branch of notless than its nominal size, when mea

13、sured in accordance withSection 4. The alignment of the side branch shall be so located1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.Current edition approved Feb. 1, 2012. Published February

14、 2012. Originallyapproved in 2001. Last previous edition approved in 2007 as F213501(2007). DOI:10.1520/F2135-01R12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to

15、the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.that the smallest inside radius of the side branch of the sanitarytee shall meet tangentially with, or within 5 % of, the mainbore

16、 (see Fig. 1), when measured in accordance with 4.4.5.NOTE 1Refer to Appendix X1 for geometric configurations of someof the fittings being produced. Consult the individual manufacturer forlaying lengths.4. Test Method for Determining Compliance of Short-Pattern14 Bends and Sanitary Tees4.1 Scope:4.1

17、.1 This test method covers the determination of thecenterline radius of short-pattern14 bends and of the sidebranch of short-pattern sanitary tees. A method of determiningthe alignment of the side branch of short-pattern sanitary teesis also included.4.2 Significance and Use4.2.1 Determination of th

18、e centerline radius of curvature ofshort-pattern14 bends.4.2.2 Determination of the centerline radius of curvature ofthe side branch of short-pattern sanitary tees.4.2.3 Determination of the alignment of the side branch ofshort-pattern sanitary tees.4.3 Apparatus4.3.1 For accuracy, the following equ

19、ipment shall be used:4.3.1.1 Lead pencil3H or harder lead 0.020 in. (0.5 mm),sharp.4.3.1.2 Set square, suitable size.4.3.1.3 Metal ruleaccurate to 0.020 in. (0.5 mm).4.3.1.4 Solid blade sawcapable of cutting a fitting in halfsquarely along the mold parting line.4.3.1.5 Photocopy machinecapable of re

20、producing the cutsurface of the fitting to be tested.4.4 Procedure4.4.1 Cut a fitting in half squarely along the mold partingline using a solid blade saw.4.4.2 Place the metal rule next to the specimen to bephotocopied. Make a photocopy of each half of the specimen.(Ensure that the outline is clearl

21、y defined. White correctionfluid or equivalent may be used.)4.4.3 Compare the metal rule to its photocopy. The photo-copy shall not be enlarged or reduced.4.4.4 Find the centerline radius of curvature for each half ofthe fitting as follows (see Fig. 1).4.4.4.1 Locate points a, b, and c on the curved

22、 line formingthe inside of the fitting, as shown in Fig. 1. Points a and c areplaced at the extremities of the curve, while point b is placedapproximately midway between a and c.4.4.4.2 Using a compass with a radius greater than12 thelength of line ab, draw two intersecting arcs with their centerat

23、a and b, locating points d and e.4.4.4.3 Draw the bisector by passing a line through the twointersecting points of the arcs (points d and e).4.4.4.4 Using c as center, in a similar manner, bisect the linebc with a line passing through the two intersecting points of thearcs (points f and g).FIG. 1 Me

24、asurement for Centerline Radius of Curvature and Branch AlignmentF2135 01 (2012)24.4.4.5 The point where the two bisectors intersect, at pointO, is the center point of the inner arc of the side branch.4.4.4.6 Extend the inner arc at point h and the inner arc atpoint i, using point O as center.4.4.4.

25、7 Draw a line through point O and point i crossing thetwo arcs at points i and j.4.4.4.8 Bisect the line ij in the manner described in 4.4.4.2and 4.4.4.3, finding point k. Line Ok is the centerline radius ofcurvature.4.4.4.9 Measure and record the length of line Ok.4.4.5 Determine the side branch mi

26、salignment (C/D Ratio)of a sanitary tee as follows (see Fig. 1).4.4.5.1 After finding point O using the method in 4.4.4.4using a set square, draw a line through point O at 90 to themain bore of the body, forming line On.4.4.5.2 Extend the arc Oi from point i until it crosses line Onat point m.4.4.5.

27、3 Extend the inside waterway of the main bore frompoint i until it crosses line On at point p.4.4.5.4 Measure and record the length of line mp, which isfactor C of the ratio.4.4.5.5 Measure and record the length of line np, which isfactor D of the ratio.4.5 Calculation and Interpretation of Results4

28、.5.1 Calculate the centerline radius of curvature (the lengthof line Ok) for the short-pattern14 bend, sanitary tee orreducing sanitary tee by averaging the centerline radius ofcurvature for each half of the fitting.4.5.2 Calculate the percent of misalignment of the sidebranch of a short-pattern san

29、itary tee by dividing the misalign-ment C (the length of line mp) by the diameter of the main boreD (the length of line np). Multiply by 100, then average theresults of both halves of the fitting.4.5.3 If the result in 4.5.2 exceeds 5 %, the measuringprocedure shall be repeated four additional times

30、 using thesame fitting sample. If any of these four results exceed 7 %, thefitting shall not be acceptable.4.6 Precision and Bias34.6.1 The percent of misalignment of the side branch (C/Dratio) of a short-pattern sanitary tee is a measurement consist-ing of the average of the two values determined f

31、or the halvesof one fitting and has been found to have a potential error of62 % when using the method described in Section 4.5. Keywords5.1 DWV; fittings; plastic; Schedule 40; thermoplasticAPPENDIX(Nonmandatory Information)X1. CONFIGURATIONSX1.1 The following fittings, descriptions, and terms areco

32、mmonly used in the plastic Drain, Waste, and Vent pipingindustry. However, these illustrations may not exhibit all theconfigurations produced. Therefore, consult the individualmanufacturer as to sizes and laying-length dimensions (seeSymbols D2749).NOTE X1.1Some fitting configurations may be made wi

33、th threadedhubs or spigot connections.3Supporting data have been filed at ASTM International Headquarters and maybe obtained by requesting Research Report RR:F17-1047.F2135 01 (2012)3FIG. X1.1 BendsFIG. X1.2 Single or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).FIG. X1.7 Cleanout TeeF2135 01 (2012)6