ImageVerifierCode 换一换
格式:PDF , 页数:4 ,大小:75.75KB ,
资源ID:537886      下载积分:5000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-537886.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM F2154-2001(2007) Standard Specification for Sound-Absorbing Board Fibrous Glass Perforated Fibrous Glass Cloth Faced《多孔纤维玻璃布面的纤维玻璃吸声板标准规范》.pdf)为本站会员(brainfellow396)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ASTM F2154-2001(2007) Standard Specification for Sound-Absorbing Board Fibrous Glass Perforated Fibrous Glass Cloth Faced《多孔纤维玻璃布面的纤维玻璃吸声板标准规范》.pdf

1、Designation: F 2154 01 (Reapproved 2007)An American National StandardStandard Specification forSound-Absorbing Board, Fibrous Glass, Perforated FibrousGlass Cloth Faced1This standard is issued under the fixed designation F 2154; the number immediately following the designation indicates the year ofo

2、riginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers fibrous glass sound-absorbingboar

3、d with a perforated fibrous glass cloth facing for soundreduction in ship spaces with high noise levels. This specifi-cation is primarily for materials used on ships. Additionalrequirements, testing, and certification are required for use ofthis material aboard U.S. Coast Guard inspected vessels in

4、theUnited States.1.2 This standard measures and describes the response ofmaterials, products, or assemblies to heat and flame undercontrolled conditions, but does not by itself incorporate allfactors required for fire hazard or fire risk assessment ofmaterials, products, or assemblies under actual f

5、ire conditions.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory requirements prior to use

6、.2. Referenced Documents2.1 ASTM Standards:2C 423 Test Method for Sound Absorption and Sound Ab-sorption Coefficients by the Reverberation Room MethodC 634 Terminology Relating to Environmental AcousticsD 3951 Practice for Commercial PackagingE84 Test Method for Surface Burning Characteristics ofBui

7、lding Materials2.2 ANSI Standard:ANSI/ASQC Z1.4 Sampling Procedures and Tables forInspection by Attributes32.3 Other Documents:46 CFR 164.012 Code of Federal RegulationsInteriorFinishes for Merchant Vessels4Navigation and Vessel Inspection Circular (NVIC) 9-9753. Terminology3.1 For definitions of te

8、rms used in this specification, seeTerminology C 634.4. Ordering Information4.1 Title, number, and date of this specification.4.2 First article sample, when required (see 7.1).4.3 Width and length required, if other than 24- by 36-in.(609.6- by 914.4-mm) board (see 8.1).4.4 Thickness required (see 8

9、.2).4.5 Density of waffle board (see 10.1).4.6 Conformance inspection reports required (see 11.1).5. Materials and Manufacture5.1 See typical construction details located in Supplemen-tary Requirements Section S3.6. Performance Requirements6.1 Surface Flame Spread and Smoke GenerationPropertiesThe s

10、ound-absorbing board shall meet the re-quirements for surface flame spread and smoke generationproperties for an U.S. Coast Guard Approved Interior Finish inaccordance with 46 CFR 164.012 or NVIC Circular 9-97.6.2 Facing SeparationWhen the sound-absorbing boardis cut or sawed, the threads of the fib

11、rous glass cloth facingacross which the cut is made shall not be separated from theface over a distance of more than 3.0 mm (18 in.). In case thefibrous glass cloth facing does not cover the entire surface ofthe board, the uncovered portion of the board shall not extendfurther than 3.175 mm (18 in.)

12、 from any edge. The fibrous glasscloth facing shall not extend over the edge of the board.6.3 Sound-AbsorptionWhen tested as specified in 10.3,the sound-absorbing board shall have coefficients of absorptionthat are equal to or greater than those shown in Table 1.1This specification is under the juri

13、sdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.02 onInsulation/Processes.Current edition approved May 1, 2007. Published June 2007. Originallyapproved in 2001. Last previous edition approved in 2001 as F 2154 - 01.2For referenced AST

14、M standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th

15、 Floor, New York, NY 10036, http:/www.ansi.org.4Available from U.S. Government Printing Office Superintendent of Documents,732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401, http:/www.access.gpo.gov.5Available from Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA152507954.1Cop

16、yright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.7. Other Requirements7.1 First ArticleWhen specified (see Section 4), the con-tractor shall furnish sample unit(s) for first article inspectionand approval (see 11.1).8. Dimensions and Tole

17、rances8.1 Width and LengthUnless otherwise specified (seeSection 4), the sound-absorbing board shall be furnished in awidth of 609.6 mm (24 in.) and a length of 914.4 mm (36 in.)(see 11.2).8.2 ThicknessThe sound-absorbing board shall be fur-nished in thicknesses of 25.4 mm (1 in.) or 50.8 mm (2 in.)

18、, asspecified (see Section 4 and 11.2).8.3 TolerancesTolerances on length and width shall notexceed 66.35 mm (14 in.). Tolerance on thickness shall notexceed 62.38 mm (332 in.) 0 mm (0 in.).9. Sampling9.1 Inspection LotFor the purpose of sampling, a lot shallconsist of all boards of the same thickne

19、ss produced underessentially the same conditions, and offered for delivery at onetime.9.2 Sampling for Visual and Dimensional ExaminationArandom sample of board shall be selected from each lot offeredfor inspection in accordance with ANSI Z1.4 at InspectionLevel II. No defects shall be allowed.9.3 C

20、onformance Test SamplingWhen density and sur-face flame spread and smoke generation property tests arerequired in accordance with 11.1.2, the samples shall beselected in accordance with 9.3.1 and 9.3.2.9.3.1 Sampling for Density TestSample boards shall beselected in accordance with ANSI Z1.4 at Insp

21、ection Level S-4for the density test of 10.1. No defects shall be allowed.9.3.2 Sampling for Surface Flame Spread and Smoke Gen-eration PropertiesA sufficient number of boards shall berandomly selected and joined end-to-end to form a specimen50.8 cm (20 in.) wide by 50.8 mm (2 in.) thick by 731.5 cm

22、 (24ft) long. The specimen shall be subject to the surface flamespread and smoke generation property test of 10.2.10. Test Methods10.1 DensityThe density of the waffle board fibrous glasslayer (see S3.1.2) shall be tested at the location of manufactureprior to fabrication into final form panels. Den

23、sity is deter-mined by dividing sample mass by sample volume. Samplemass is measured to the nearest 1.0 g and sample volume ismeasured to the nearest 1 cm3of water displaced by onestandard board as specified (see 9.3.1).10.2 Surface Flame Spread and Smoke GenerationPropertiesThe test specimens (see

24、9.3.2) shall be tested inaccordance with Test Method E84(see S5).10.3 Sound Absorption CoeffcientsThe sound-absorbingboard shall be laid directly on the floor of a reverberation roomand tested in accordance with Test Method C 423.11. Inspection11.1 Type approvals for 46 CFR 164.012 include inspectio

25、nrequirements as part of the specific type approval.12. Packaging12.1 Commercial PackagingCommercial packaging shallbe in accordance with Practice D 3951.13. Keywords13.1 fibrous glass cloth; perforated fibrous glass cloth;reverberation room method; sound absorbing; sound absorp-tion coefficient; so

26、und reduction; surface flame spread andsmoke generation properties; waffle boardSUPPLEMENTARY REQUIREMENTS(Mandatory Information for U.S. Navy)This specification is adapted from MIL-A-23054.S1. Supplemental Requirements and Exceptions to theRequirements of This Specification for Ships of theU.S. Nav

27、yS1.1 DoD Intended UseThe sound-absorbing board cov-ered by this specification is intended for reduction of sound inspaces where there is a high level of noise.TABLE 1 Minimum Sound-Absorption CoefficientsBoard Thickness, Frequency, Hzmm in. 125 250 500 1000 2000 400025.4 1 0.07 0.25 0.70 0.90 0.75

28、0.7050.8 2 0.25 0.70 0.90 0.85 0.75 0.75F 2154 01 (2007)2S2. Referenced DocumentsS2.1 Military Specifications:MIL-I-742 Insulation Board, Thermal, Fibrous Glass6MIL-A-3316 Adhesives, Fire-Resistant, Thermal Insulation6MIL-C-20079 Cloth, Glass; Tape, Textile, Glass; andThread, Glass6S3. Materials and

29、 ManufactureS3.1 MaterialThe sound-absorbing board shall be a lami-nate consisting of a perforated fibrous glass cloth facing, ahigh-density fibrous glass layer waffle board, and a fibrousglass backing board. Asbestos fibers and components contain-ing asbestos fibers are prohibited.S3.1.1 Backing Bo

30、ardThe backing board shall conform totype II of MIL-I-742 unfaced board except that the board shallbe furnished in nominal thickness of 19.05 mm (34 in.) or44.45 mm (134 in.) (see 5.1.2 and 8.2).S3.1.2 High-Density Fibrous Glass LayerThe fibrousglass layer shall have a density of not less than 160 k

31、g/m3(10lb/ft3) (see 10.1). The layer shall consist of glass fibersimpregnated with a suitable binder and compressed or other-wise formed into a waffle. The nominal thickness of thehigh-density fibrous glass layer shall be 6.35 mm (14 in.).S3.1.2.1 WaffleThe waffle shall be constructed having4.76mm (

32、316-in.) deep indentations tapering from a nominal6.0mm (14-in.) diameter to a nominal 3.175mm (18-in.)diameter indentations on a 12.7mm (12-in.) center.S3.1.3 Fibrous Glass Cloth FacingThe cloth used forfacing the high-density fibrous glass layer shall conform toType I, Class 2 of MIL-C-20079. The

33、cloth facing shall beimpregnated with a hardening agent. The cloth facing shall beperforated with nominal 4.76mm (316-in.) diameter holes on a12.7-mm (12-in.) center.S3.1.3.1 Facing AdhesiveThe impregnated fibrous glasscloth facing shall be compatible with adhesive conforming toType II of MIL-A-3316

34、. The adhesive strength requirementsfor securing fibrous glass cloth facing to the high-densityfibrous glass layer shall conform to MIL-A-3316.S3.2 Recycled, Recovered, or Environmentally PreferableMaterialsRecycled, recovered, or environmentally prefer-able materials should be used to the maximum e

35、xtent possibleprovided that the material meets or exceeds the operational andmaintenance requirements, and promotes economically advan-tageous life cycle costs.S3.3 ConstructionOne side of the high-density fibrousglass layer shall be adhered to the backing board and the otherside adhered to the fibr

36、ous glass cloth facing, using adhesive.The fibrous glass cloth facing shall be free of wrinkles or otherirregularities. The sound-absorbing board shall be so designedthat the perforations in the fibrous glass cloth facing shall becentered over the indentations in the waffle-type high-densityfibrous

37、glass layer.S4. Department of Defense PackagingS4.1 DoD PackagingFor acquisition purposes, the pack-aging requirements should be as specified in the contract ororder. When actual packaging of material is to be performed byDoD personnel, these personnel need to contact the responsiblepackaging activi

38、ty to ascertain requisite packaging require-ments. Packaging requirements are maintained by the Inven-tory Control Points packaging activity within the MilitaryDepartment or Defense Agency, or within the Military Depart-ments System Command. Packaging data retrieval is availablefrom the managing Mil

39、itary Departments or Defense Agen-cys automated packaging files, CD-ROM products, or bycontacting the responsible contracting activity.S5. Performance RequirementsS5.1 Surface Flame Spread and Smoke GenerationPropertiesThe sound-absorbing board shall have a flamespread index less than 30 and smoke d

40、evelopment less than 100when tested as specified in 10.2.S6. InspectionS6.1 Classification of InspectionsThe inspection require-ments specified herein are classified as follows: (1) first articleinspection (see 11.1.1), and (2) conformance inspection (see11.1.2).S6.1.1 First Article InspectionThe fi

41、rst article inspectionshall consist of the examination and tests shown in Table S6.1.S6.1.2 Conformance InspectionConformance inspectionshall consist of the visual and dimensional examination ofS6.2. The density test of 10.1 shall be tested on each lot ofmaterial. New tests for density (10.1) and fi

42、re resistance (10.2)are required whenever the manufacturing methods or compo-nent materials are changed and reports supplied when re-quested.S6.1.3 ExaminationEach of the boards selected in accor-dance with 9.2 shall be examined to verify compliance with thedimensional requirements of this specifica

43、tion. When measur-ing length, width, or thickness, any convenient measuring rulegraduated to 1.59 mm (116-in.) shall be used. Any board in thesample containing one or more defects shall be rejected. If thesample contains3%ormore of defective boards, the entire lotrepresented by the sample shall be r

44、ejected. The facingseparation and workmanship examinations shall be included.S6.1.4 WorkmanshipThe insulation shall be free of visualdefects that will adversely affect the service quality. Forexample, holes or delamination of the facing when occurring toan excessive degree shall be judged to adverse

45、ly affect theservice quality of the material.6Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.TABLE S6.1 First Article InspectionInspectionRequirementParagraphExamination andTest ParagraphVisual and dimensional examina

46、tion 8.1-8.3 11.2Density S3.1.2 10.1Surface flame spread and smokegeneration properties10.2 6.1Sound absorption 6.3 10.3F 2154 01 (2007)3ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this sta

47、ndard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years an

48、dif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee,

49、which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1