ASTM F2242-2005(2013) Standard Specification for Production Acceptance Testing System for Powered Parachute Aircraft《动力伞降飞行器用生产验收测试系统的标准规范》.pdf

1、Designation: F2242 05 (Reapproved 2013)Standard Specification forProduction Acceptance Testing System for PoweredParachute Aircraft1This standard is issued under the fixed designation F2242; the number immediately following the designation indicates the year oforiginal adoption or, in the case of re

2、vision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 The following requirements apply for the manufacturepowered parachute aircraft. This specification

3、 includes theproduction acceptance test requirements for powered parachuteaircraft.1.2 This specification applies to powered parachute aircraftseeking civil aviation authority approval, in the form of flightcertificates, flight permits, or other like documentation.1.3 This standard does not purport

4、to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory requirements prior to use.2. Terminology2.1 Definitions:2.1.1 powered parac

5、hute, naircraft comprised of a flexibleor semi-rigid wing connected to a fuselage in such a way thatthe wing is not in position for flight until the aircraft is inmotion. This aircraft has a fuselage with seats, engine, andwheels (or floats), such that the wing and engine cannot beflown without the

6、wheels (or floats) and seat(s). Unique to thepowered parachute is the large displacement between thecenter of lift (high) and the center of gravity (low), which ispendulum effect. Pendulum effect limits angle of attachchanges, provides stall resistance and maintains flight stability.3. Significance

7、and Use3.1 The purpose of this specification is to provide theminimum requirements for the establishment of a ground andflight test program for verifying the initial (first run) productionaircraft meets certain operational performance requirementsthat have been set forth by the manufacturer in its A

8、ircraftOperating Instructions.3.2 In addition, this specification provides minimum re-quirements to verify that each subsequent production airplanehas no obvious defects that would prevent the safe operation ofthe airplane.4. Production Acceptance Testing, Ground Testing4.1 Inspection VerificationTh

9、ere shall be a written proce-dure in effect to verify all top-level inspections have beencompleted and no discrepancies remain open.4.2 Engine Break-InThere shall be a written procedure ineffect to perform the engine break-in. This procedure mayinclude all engine gage verification of operation. All

10、enginereadings shall achieve the normal accepted range of readingscommensurate with a new engine. If not performed duringengine break-in, then this verification must be performed underseparate procedures. All engine gages shall be verified to beoperating.5. Production Acceptance Testing, Flight Test

11、ing5.1 Every production aircraft shall be flight tested to thefollowing minimums:5.1.1 Powered ParachutesFifteen minutes flight time,including at least one takeoff and landing, trimming of flightcontrols, and verification of control for left turn, right turn, andflare (flare only if so equipped).5.2

12、 Instrument VerificationThere shall be a written proce-dure in effect to verify that all other instruments are operatingwithin normal ranges. If equipped with a compass, the compassvariation card data shall be developed with the engine running.6. Post Flight Acceptance6.1 There shall be a written pr

13、ocedure in effect to performpost flight inspection that will review all flight critical attach-ments and structures.6.2 The reviewing personnel shall sign all post flight reviewdocuments.7. Documentation:7.1 There shall be a written procedure in effect to properlydocument and store the production ac

14、ceptance test results suchthat they are correlated to the specific aircraft for futurereference.1This specification is under the jurisdiction of ASTM Committee F37 on LightSport Aircraft and is the direct responsibility of Subcommittee F37.30 on PowerParachute.Current edition approved June 1, 2013.

15、Published August 2013. Originallyapproved in 2003. Last previous edition approved in 2008 as F2242 05 (2008).DOI: 10.1520/F2242-05R13.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States17.2 Test Failures:7.2.1 There shall be a written pro

16、cedure in effect to reviewthe causes for any aircraft failures in the production acceptancetests phases. Aircraft may only be released for retest aftermanufacturing review of the discrepant articles and writtenrelease for retest.8. Keywords8.1 light sport aircraft; powered parachute aircraft; specia

17、lairworthiness certificateASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infrin

18、gement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard

19、 or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views

20、 known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F2242 05 (2013)2