ASTM F2252-2003 Standard Practice for Evaluating Ink or Coating Adhesion to Flexible Packaging Materials Using Tape《使用胶带评估柔性包装材料与墨水或涂层间粘性的标准实施规程》.pdf

1、Designation: F 2252 03Standard Practice forEvaluating Ink or Coating Adhesion to Flexible PackagingMaterials Using Tape1This standard is issued under the fixed designation F 2252; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the

2、 year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice describes a means of evaluating ink orcoating adhesion to flexible packaging materials. This p

3、racticeis intended for use on flexible packaging materials whosesurfaces are not damaged by the application and removal oftape.2. Referenced Documents2.1 ASTM Standards:2D 1898 Practice for Sampling of Plastics3D 3330/D 3330M Test Method for Peel Adhesion ofPressure-Sensitive TapeD 4332 Practice for

4、 Conditioning Containers, Packages, orPackaging Components for Testing3. Significance and Use3.1 Poor adhesion of ink or coating to the base substrate canimpact the readability of printed materials, affect the function-ality of coated materials, or create a source of contamination.This practice prov

5、ides a means for evaluating the adhesion ofink or coating to a flexible packaging material.3.2 For purposes of resolving inter-laboratory disagree-ments, test methods developed from this practice may beimproved by defining and controlling the pressure and methodof tape application, (for example, usi

6、ng weighted roller), andthe speed and angle of tape removal.3.3 This practice does not address acceptability criteria.These need to be jointly determined by the user and producerof the product.4. Apparatus4.1 3M #610 or Sellotape office adhesive tape is commonlyused for this procedure, typically 19

7、to 25 mm (34 to 1 in.)wide. Whichever tape is chosen should be agreed upon bycustomer and supplier.4.1.1 Manufacturers storage and shelf-life recommenda-tions should be followed or acceptability determined throughreal-time aging and laboratory tests. Test Method D 3330/D 3330M gives guidance on test

8、ing. Again, as stated in 3.3,acceptability criteria is a matter of agreement between cus-tomer and supplier.5. Sampling5.1 The number of samples tested should be adequate to bepredictive of performance. Caution should be taken wheneliminating samples with defects as this can bias results.5.2 See Pra

9、ctice D 1898 for guidance on standard samplingpractices.6. Conditioning6.1 Conditioning of the samples will depend on the materialunder evaluation. If conditioning before testing is appropriate,normal, and desirable, then condition the test specimens at 236 2C (73.4 6 3.6F) and 50 6 5 % RH for not l

10、ess than 24h prior to test.6.2 Before testing catalyzed or cured inks or coatings, orboth, ensure that the samples have been exposed to theappropriate conditions for sufficient time to allow completecure.6.3 See Practice D 4332 for guidance on conditioning prac-tices.7. Procedure7.1 Lay sample to be

11、 tested on a flat surface. Sample shouldlay flat and smooth without wrinkles, creases, or folds.7.2 Cut a piece of tape long enough to cover the printed orcoated area of interest on the sample. For large areas it may beeasier to work with several shorter pieces of tape. Handling1This practice is und

12、er the jurisdiction of ASTM Committee F02 on FlexibleBarrier Materials and is the direct responsibility of Subcommittee F02.20 onPhysical Properties.Current edition approved Oct. 1, 2003. Published December, 2003.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Cu

13、stomer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.application and remova

14、l of tape is simpler when length of tapedoes not exceed 12 in.7.3 Apply tape to sample using a smooth even motionwithout wrinkling tape or sample. Run thumb or forefingeralong tape to make sure it is fully adhered, without any bubblesin surface.7.4 Hold sample flat to surface with one hand, use othe

15、rhand to peel back tape at an angle of approximately 120 to150. Lift tape, pulling back with an even, moderate motion.Typically 305 to 460 mm (12 to 18 in.) per second.NOTE 1Varying the amount of time after tape is applied may affectthe results.7.5 Examine the test sample for missing print or coatin

16、ggaps.7.6 Examine tape for any ink or coating removed from thetest sample. As an aid for visual inspection reference standardsmay be created and used to determine degree of transfer.7.7 Record results. Characterize the degree of adhesionusing mutually agreed upon references. If multiple colors ofink

17、 are present, results may vary by color and may be reportedthat way. This is a subjective test and operator training iscrucial for consistent reporting of test results.8. Keywords8.1 adhesion; anchorage; coating; ink; print; tape testASTM International takes no position respecting the validity of an

18、y patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to rev

19、ision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your

20、 comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyr

21、ighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F2252032