ASTM F2272-2009 Standard Specification for Paintball Markers.pdf

1、Designation: F2272 09An American National StandardStandard Specification forPaintball Markers1This standard is issued under the fixed designation F2272; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A n

2、umber in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers paintball markers, which pro-pel a paintball by means of energy released by compressed air,compressed gas, or

3、other means.1.2 LimitationsThis specification does not cover non-recreational paintball markers, for example, those used by lawenforcement, scientific, military or theatrical entities.1.3 The values stated in SI units are to be regarded as thestandard; the inch-pound units in parentheses are provide

4、d forinformation only.1.4 The following precautionary caveat pertains only to thetest method portion, Section 8, of this specification. Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establi

5、sh appropriate safety and healthpractices and determine the applicability of regulatory require-ments prior to use.2. Referenced Documents2.1 ASTM Standards:2F1776 Specification for Eye Protective Devices for Paint-ball SportsF1979 Specification for Paintballs Used in the Sport ofPaintballF2041 Spec

6、ification for Paintball Marker Warnings32.2 ANSI Standard:Z535.1 Safety Color Code43. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 auto-triggera trigger which, when held in the dis-charge position, will automatically cause the paintball markerto discharge when the pump or bolt

7、 action is manipulated.3.1.2 backstopan object intended to stop a paintball.3.1.3 barrelthat portion of a paintball marker throughwhich the paintball is discharged.3.1.4 barrel blocking devicea muzzle blocking safetydevice which, when properly installed, reduces the likelihoodof an intact paintball

8、discharging from the marker or leavingthe confines of the barrel blocking device. The device is oftenreferred to as a barrel plug.3.1.5 burst mode markera burst mode marker may dis-charge two or more times per trigger cycle or may dischargetwo or more times with the pull and release of the trigger.3

9、.1.6 cautionary statementthe warning outlined in Sec-tion 8 of this standard and noted in Specification F2041, whichis to be placed on paintball markers, packaging and literature.3.1.7 disabling devicea device which, when activated,disables a part of the paintball marker, usually the trigger, toprev

10、ent unintentional discharges and must be released to allowthe marker to be discharged by the movement of the trigger.The device is sometimes referred to as the “safety,” “safetybutton,” or “safety lever.” An electronic on/off switch isconsidered a disabling device when placing it in the “off”positio

11、n renders the marker inoperable.3.1.8 discharge modea mode that controls the number ofpaintballs discharged per trigger cycle.3.1.9 enhanced trigger mode markera paintball markerthat at some point discharges more than one paintball pertrigger cycle. This includes markers that “store” the number oftr

12、igger pulls and discharge more than one paintball at somepoint.3.1.10 feed mechanisma mechanism that stores, trans-ports and facilitates the loading of paintballs. It may be gravity,mechanically or air assisted or automatic in its actions.3.1.11 fully-automatic mode markera marker that dis-charges w

13、hen the triggering device is actuated and continues todischarge until the trigger returns to its reset or recycleposition.3.1.12 hoppera device used with a paintball marker tostore paintballs.1This specification is under the jurisdiction of ASTM Committee F08 on SportsEquipment and Facilities and is

14、 the direct responsibility of Subcommittee F08.24 onPaintball and Equipment.Current edition approved Nov. 1, 2009. Published December 2009. Originallyapproved in 2003. Last previous edition approved in 2008 as F2272 08. DOI:10.1520/F2272-09.2For referenced ASTM standards, visit the ASTM website, www

15、.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn. The last approved version of this historical standard is referencedon www.astm.org.4Available from American

16、National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.1.13 impact testerdevice used to test for accidentaldischarges of paintball marker. See Fig. 1.3.1.14

17、 modified fully automatic mode 1 markera semi-automatic mode marker which, after the trigger is pulled atleast three times within 1 s, is able to function in a fullyautomatic mode with a firing rate not to exceed 15 shots persecond until the trigger is released.3.1.15 modified burst mode 2 markera s

18、emi-automaticmode marker which, after the trigger is pulled at least threetimes within 1 s, is able to cycle more than one time per triggerpull with a firing rate not to exceed 15 shots per second.3.1.16 paintballa spherical ball, commonly with a diam-eter of 17.3 mm (0.68 in.), comprised of a shell

19、 and a fill,designed to be expelled from a paintball marker, as defined inSpecification F1979.3.1.17 paintball markera device specifically designed todischarge paintballs. The device is sometimes referred to as apaintball gun.3.1.18 pump mode markera marker that requires theoperator to manually cock

20、 or engage the sear of the markerbefore each shot by a means of a pump, bolt, lever, cockinghandle or similar device.3.1.19 rangethe maximum distance to which an objectmay be propelled, whether limited by energy or an obstacle.3.1.20 response triggera semi-automatic paintball markerin which after fi

21、ring the trigger is assisted back to the resetposition.3.1.21 searthe catch that holds the mechanism in theready-to-discharge position until released by the user, usuallythrough trigger movement.3.1.22 selector switcha switch (either internal or external)regardless of method of activation that is de

22、signed to allow theconsumer to change the markers discharge mode.3.1.23 semi-automatic mode markera semi-automaticmarker discharges one time with each trigger cycle. Markersthat “store” the number of trigger pulls and discharge morethan one paintball at some point do not meet this definition.Markers

23、 that operate in any other discharge mode(s) do notmeet this definition.3.1.24 standard ambient temperature and pressure(SATP)used to describe a substance at the pressure of 1 bar(1.01325 atmospheres, 750 mm Hg, 14.5 psi, 100 kPa) and atemperature of 25C (77F).3.1.25 targetthe object at which the pa

24、intball is dis-charged.3.1.26 triggera device operated by the user to discharge amarker.3.1.27 trigger, adjustablea trigger mechanism in whichthe trigger pull is adjustable.3.1.28 trigger cyclethe movement of the trigger throughdischarge and returning to a reset or recycle position.3.1.29 trigger, d

25、ouble-actiona trigger mechanism inwhich a single continuous action of the trigger moves theA. YokeB. Pivot BoltC. SwivelD. 91.29 cm (36 in.) Strap or RopeE. 60.86 cm (24 in.) aluminum bar with 1.27 cm (0.5 in.) diameter or 1.9 cm (0.75 in.) copper tubeF. Hook and loop strap able to suspend marker pa

26、rallel to and 15.21 cm (6 in.) below EFIG. 1 Marker Suspension SlingF2272 092hammer to the discharging position and then releases it todischarge the paintball.3.1.30 trigger guarda rigid, firmly attached component. Itmust totally enclose the trigger area and be wider than thetrigger. There can be no

27、 more than 38 mm (1.5 in.) of spacefrom any point on the face of the trigger to the trigger guard,and no more than 13 mm (0.5 in.) from the lowest point of thetrigger to the trigger guard. All measurements under this ruleare to be taken after excluding any removable attachments tothe trigger.3.1.31

28、trigger pullthe force required to move the triggerfrom its start or recycle/reset position to a position thatdischarges the marker.3.1.32 velocity adjustera device designed to establish thevelocity at which a paintball is discharged.4. Significance and Use4.1 This specification establishes performan

29、ce requirementsand test methods for paintball markers.4.2 This specification identifies the minimum warnings andinstructions that are to be provided in literature, on labels, onpackaging and on the marker itself.5. Conformance5.1 Paintball markers shall not, either by label or othermeans, indicate c

30、onformance with this specification unless, atthe time of manufacture, they conform with all applicablerequirements contained herein.6. General Requirements6.1 LiteratureLiterature shall be provided with eachpaintball marker and shall include, as applicable, the instruc-tions, cautionary statements a

31、nd safety tips specified in Section8.6.2 Packaging:6.2.1 Packaging shall be labeled in a prominent and con-spicuous manner in accordance with the provisions of 8.5.6.2.2 All paintball markers that include a barrel must bepackaged with a barrel blocking device.6.3 FinishThe exposed edges of all paint

32、ball markersshall be smooth and free of sharp edges and burrs. The exposedsurface of all wood parts shall be smooth and free of splinters.6.4 Shipping:6.4.1 Each paintball marker shall be shipped in an unloadedand degassed condition.6.4.2 All paintball markers must shoot at a velocity under91.44 m/s

33、 (300 ft/s) at the time of shipment at SATP.6.5 Design:6.5.1 All paintball markers with an exposed trigger shallhave a trigger guard.6.5.2 All paintball markers intended to be used with refill-able cylinders shall be able to withstand input pressure of threethousand pounds per square inch 207 bar (3

34、000 psi) withoutcatastrophic failure. Leaking in a manner which would notcause injury to the operator shall not constitute failure.6.5.3 Amarkers performance may not be enhanced, includ-ing but not limited to increasing the markers velocity, withoutthe use of tools or the need for disassembly. In th

35、e event thata marker requires an internal switch, jumper or other device tobe set prior to using outside adjustments, it will be consideredto meet this requirement provided that tools or disassembly arerequired to access the switch, jumper or similar device.6.5.4 All paintball markers shall only ope

36、rate in pump,semi-automatic, modified fully automatic mode 1, or modifiedburst mode 2, response trigger, or a combination thereof, asdefined in this standard.7. Performance Requirements7.1 Marker FunctionThe cocking or pumping mechanismof a paintball marker shall not cause a marker to dischargeunint

37、entionally while a marker is being cocked in accordancewith the manufacturers instructions. This does not limit theuse of “auto-triggers.” Markers shall be pump, semi-automatic,modified fully automatic mode 1, or modified burst mode 2,response trigger, or a combination thereof, as defined in thissta

38、ndard.7.2 Gas Propellant Source RetentionMarkers shall bedesigned so that a gas propellant source does not inadvertentlyeject from the marker during use or otherwise.7.3 Disabling DeviceDisabling devices shall be providedon all paintball markers and all such devices can be endedwhether or not the ma

39、rker is cocked. All such devices shall beclearly marked to indicate the “safe” and “fire” or “on” and“off” positions in accordance with 8.6.4. All such devices shallbe capable of preventing the markers from being dischargedwhen a weight of 13.6 kg (30 lb) is applied to the trigger. Testsshall be con

40、ducted in accordance with 8.3.7.4 Accidental DischargeMarkers should not accidentallydischarge when exposed to a moderate jolt in accordance with8.3.8. Test Methods8.1 No precision statement on any of the following testmethods is available at this time.8.2 Disabling Device Test:8.2.1 SignificanceThi

41、s method determines if the disablingdevice will withstand a 13.6 kg (30 lb) applied weight withoutfailure, causing the marker to discharge.8.2.2 ApparatusA trigger weight system having a 13.6 60.02 kg (30 6 0.05 lb) weight. Arrange the weight system sothat the weights can be picked up by the trigger

42、 of the markerwith the marker in a vertical position, muzzle up. (A springgage, capable of measuring the trigger force, can be usedinstead of weight system.)8.2.3 Test SpecimenThe test specimen shall consist of anew paintball marker, selected in accordance with the manu-facturers usual quality assur

43、ance practices.8.2.4 Procedure:8.2.4.1 Conduct the test at SATP.8.2.4.2 Conduct all tests without paintballs in the marker.8.2.4.3 Place disabling device in “safe” position or theelectronic switch in the “off” position.8.2.4.4 Apply a 13.6 kg (30 lb) load at the center point of thetrigger for 30 s w

44、ith the load applied to the center of the faceof the trigger and remove the load.F2272 0938.2.4.5 Put disabling device in the “fire” position or theelectronic switch in the “on” position. The marker must notdischarge as the safety is disengaged.8.2.4.6 Test the marker for proper trigger and disablin

45、gdevice action.8.2.4.7 The marker passes the test if it withstands the loadapplied without causing the marker to discharge during theapplication of the load and does not discharge upon thedisengagement of the disabling device, and the disablingdevice and trigger function properly after testing.8.3 A

46、ccidental Discharge Test:8.3.1 SignificancePaintball markers should not dischargewhen jarred or jolted in a moderate manner while theirdisabling device is disengaged.8.3.2 Test SpecimenThe test specimen shall consist of anew paintball marker, selected in accordance with the manu-facturers usual qual

47、ity assurance practices.8.3.3 Procedure:8.3.3.1 Conduct the test at SATP.8.3.3.2 Attach a properly charged propellant source inaccordance with the manufacturers instructions. Test dis-charge the marker.8.3.3.3 Leave the marker in the ready to discharge condi-tion.8.3.3.4 Suspend marker using a sling

48、 (see Fig. 1).8.3.3.5 Place the cocked impact tester (see Fig. 2) againstthe side of the marker centered on the grip frame directlybehind the center point of the trigger with the impact testerfirmly affixed to an immobile surface.8.3.3.6 Release the impact tester and observe if the markerdischarges.

49、8.3.3.7 Repeat by impacting the marker on the followingaxis:(1) 180 degrees to the first impact.(2) The front of the barrel aligned with the barrels axis.(3) The rearmost point of the marker aligned with thebarrels axis.8.3.3.8 The marker fails if it discharges on any impact.8.4 Barrel Blocking Device Requirement:8.4.1 SignificanceAll paintball markers which include abarrel must be packaged with a barrel blocking device.8.4.2 Test SpecimenThe test specimen shall consist of anew paintball marker, packaged in the manufacturer